开云体育

I just tested again, Both 32 bit Buster and 32 bit Bullseye dated Jan 2022 from RaspberryPi.com I added ssh.txt and wpa_supplicant.conf to the boot partition prior to putting in my RPi4-8GB (with

Hi I am attempting a new build of both Buster and Bullseye with a date of 1-28-22 I think, at least in Jan of 2022. On buster it loads and works good, but when attempting to use BAP it has notices of

Hi Kevin I tried out, as you described with a fresh install. I added dtoverlay=disable-wifi as last line to config and rebooted. After reboot I typed ip a and wlan0 was still present. So I shut down

The original purpose of the RPi was as a low-cost computer to introduce school age children to what many refer to as 'hands-on computing", with additional hardware to make the boards appeal to

Should that be on the radio usb-d ? The radio will ptt on usb data but I can’t make any connection with any station to send a email ,or should the Pat set up be configured to usb-d ?

If you use a wpa_supplicant.conf file, it must have a country= line in it. If you set up WiFi in raspi-config, be SURE to enable Localization, WLAN-Country, If you don't do either, there is a

Everything appears to be configured correctly with maybe one exception. After pressing "connect" in the Pat Inbox, what mode is your radio in (USB or USB-D?) It should probably be in USB-D. Educated

This should work: xdg-settings set default-web-browser *chromium-browser.desktop * Thanks for the info Jay. I just played with the file until I found the right combination. I didn't take the time to

David -- good morning. Raspberry Pi WiFi is not very good! I too have suffered hours of frustration trying to get it to work after it appears -- usually after a reboot -- to stop working! VERY

Jason, Those settings that you used: Uncomment the following lines: framebuffer_width=1920 framebuffer_height=1080 Note: you can change the resolution here to suit your needs. Uncomment this line:

Hello and thank you all...? Well I struggled last nite after a fresh install of build a pi on a pi4b 8 g in ar gon case. I have conky running to check the ip info.. have wire but no wireless.. I

On Sat, Mar 5, 2022 at 07:32 AM, km4ack wrote: > > In Pat Menu, click on "quick stats" and post a screenshot please. > -- > 73, de KM4ACK > YouTube ( https://youtube.com/km4ack ) | Tip Jar ( >

I'm running Bullseye 11.2???? 32 bit on a Pi 3B+ I installed WSJT-X prior to installing latest PAT.? Running the full FLDIGI suite with PAT, ARDOP, etc.? Jason found some problems with my PAT

Jay: I've forked my systems, roughly 2/3rd will be staying on Buster 32 due to RPiFoundation's dropping support for projects that have been supported from the beginning, namely PiCam (CSI Cameras,

New discovery this morning.? If I have my radio and power supply off when I boot my RPI, then turn on the power supply.... it all works.? If the power supply alone is on when the RPI boots, no

Jason & gang, I know I mentioned on Patreon that I’ve been resisting Bullseye, mainly because I couldn’t get headless screen resolution resolved. I’ve corrected that problem and it also is

Clean install of RaspberryPiOS Bullseye on Pi4-8GB Add wpa_supplicant.conf to /boot boot latest updates run command ip a see wifi is present as wlan0 add dtoverlay=disable-wifi to /boot/config.txt

Thanks Jason =) -- *73's Pat N5VMO*

Glad you got it figured out. I always setup, build, and run my Pi's headless with the exception of one particular machine. This is using the Pi's built in VNC server. -- 73, de KM4ACK YouTube (

In Pat Menu, click on "quick stats" and post a screenshot please. -- 73, de KM4ACK YouTube ( https://youtube.com/km4ack ) | Tip Jar ( https://www.paypal.me/km4ack ) Twitter (