开云体育

As long as you confirmed the user & grid are set in pat configure, ignore the quick stats. Could just be a minor bug. I'll fire up a pi and see if mine does the same thing. Did you resolve FLRIG not

OK No problem. This is what is going on. /etc/profile is a file that you need to edit. It is located in the /etc folder. You don't need to change to that directory, you can edit it from your home

Thanks Mike, I will give it a try later on. I am a bit unclear about; do I go to a folder and where is the command 'export XDG_CONFIG_$HOME/.config' is supposed to end up? You may have answered the

Edit /etc/profile and add the following at the end:?export XDG_CONFIG_HOME=$HOME/.configRebootThis has fixed my conky issues, and some others,but I forget which onesSent from my Verizon, Samsung

Hi Folks, I have tried to install '73 Linux' on a new 8GB Pi5. Conky is blank and I cannot access the Pi? (or any other device) via VNC Viewer. Even though I have the official power supply (27w) I

This page has info on various RPi usage, and indicates bare RPi draws only 600 mA, which seems right based on my tests with RPi 5, NVMe board and active cooler, which was well under 1 amp - BUT I had

Powerwerx offers a couple options to convert 12v to 5v USB or USB PD (multi-volt options). 3 amps - https://powerwerx.com/usbbuddy2-powerpole-usb-device-charger 75W PD -

I use the Powerwerx converters. They use Anderson powerpoles. [email protected]> wrote:

Exactly! I'll have everything running on 12 volts when remote and I am using a Pi 5. Would like to stay away from running an inverter to save the battery. 12 volts to 110 volts? just to run a 5 volt

CLI: /usr/local/bin/rigctld Rig Control Command: /usr/local/bin/rigctl -m 4 Mycall and locator are set correctly in pat configure. I re-installed Pat and Pat menu, deleted confg.jason and setup

The Pi4 calls for 3A, the Pi5 calls for 5A. You can use a 3A power supply with a Pi5 but you are limited to 600ma on attached USB devices and may also have performance issues. [email protected]>

I have not found the need for 5 amps. I have been using one of these with a Raspberry Pi 4 and it has worked fine. https://www.ebay.com/itm/384120747227 Zack W9SZ [email protected]>

Anyone have favorable experiences with any of the 12 to 5 volt @5 amp converters that are out there. There are a bunch of them on Amazon but the reviews are all over the place and indicate issues

Did you start the packet modem with Pat Menu? -- 73, de KM4ACK YouTube ( https://youtube.com/km4ack ) | Tip Jar ( https://www.paypal.me/km4ack ) Twitter ( https://twitter.com/km4ack ) | Store (

Verify the rig control command has the correct path. Run whereis rigctld in the terminal and the path should match what is set it Pat Menu "Rig Control Command" What's concerning though is that

I am starting VARA from Pat Menu. Not sure the exact location of the rig control statement, I attached what I think you are looking for. After adding the last three lines to the config file Conky is

The sound card is configured in direwolf.conf file found in the home directory. Once direwolf is started and running in the background then YAAC should be started and the AGWPE port configured to

Haven't seen the black square on VARA before so not sure why that is happening. Are you starting VARA from Pat Menu? What's your rig control statement in Pat Menu settings? A fix for the Conky

Good evening, I have a Raspberry Pi 4 running the latest Rasberry Pi OS. I am using a Digirig with an AnyTone AT778UV (No CAT control). With my Windows 10 laptop, I am able to get Winlink Express to

Now VARA HF has black panes and none of the menus are responsive, I can X out of the program. I have uninstalled and reinstalled VARA.