Re: Heads-up for Canadian Miady battery
Hey Terry, I don't know what size batteries you use in your chair. However I got rid of my 2 heavy as fun! And replaced with liposuction. My chair will actually travel about 3 miles further with less weight. I then took two more of these lightweight batteries to make a radio pack with. I forget about them often on back of chair and have nearly caused a fire by crushing one of them when backed up out of way. After that, I don't leave attached to chair unless actively using it. The two Batts in chair were 12@55A, which make for great backup system in house with the yearly exchange on batteries.
On Sat, Feb 12, 2022, 8:52 AM Don Poaps < va7dgp@...> wrote: The only reason I posted was the price in Canadian dollars.?
There's a difference between Amazon.Com and Amazon.CA.
73 Don Poaps
New Westminster, BC
VA7DGP DATA VA7QU ? VOICE Winlink: va7qu@...
Subject://wl2k ? ? ? ? ? ALLSTAR ?530780 Hamshack Hotline 5971 Mid-Island Phone Mesh 2210 2232
? ? ? ? ? ? ? ? ? ?
On Sat, Feb 12, 2022 at 8:46 AM WA4TUX Dave < wa4tux@...> wrote: Hey Don,
I've picked up a couple of these on the US Amazon store:
73, de dave/WA4TUX
|
I don¡¯t have any experience doing this but I would think you could use a cheap SDR receiver dongle and software to look at the signal. You should be able to see how wide it is on the screen.
toggle quoted message
Show quoted text
On Feb 12, 2022, at 11:53 AM, Pieter V51PJ via < v51pj@...> wrote:
Look at data over a scope. It must be pure sinewave then you know levels etc are 100%. Normaly at about 2.5khz deviation is good.? Greetings from the Namib
Pieter Jacobs +264811277615 NETS NTNSS ?For 9600 Baud AX25, Yaesu recommends using a Deviation Meter to set the deviation. ?I get intermittent success with various sites and probably need to adjust my radio.
Does anyone have an idea for an inexpe
|
BAP, Direwolf, Digirig and Baofeng PTT setup?
Yesterday I ordered a Digirig and Baofeng cable. I am running BAP
What changes do I need to make to direwolf.conf to enable PTT in this configuration?
thank you
|
Look at data over a scope. It must be pure sinewave then you know levels etc are 100%. Normaly at about 2.5khz deviation is good.? Greetings from the Namib
Pieter Jacobs +264811277615 NETS NTNSS nets@...
toggle quoted message
Show quoted text
On 12 Feb 2022, at 18:51, Don via groups.io <Ddodge40@...> wrote:
?For 9600 Baud AX25, Yaesu recommends using a Deviation Meter to set the deviation. ?I get intermittent success with various sites and probably need to adjust my radio.
Does anyone have an idea for an inexpe
|
Re: Heads-up for Canadian Miady battery
The only reason I posted was the price in Canadian dollars.?
There's a difference between Amazon.Com and Amazon.CA.
73 Don Poaps
New Westminster, BC
VA7DGP DATA VA7QU ? VOICE Winlink: va7qu@...
Subject://wl2k ? ? ? ? ? ALLSTAR ?530780 Hamshack Hotline 5971 Mid-Island Phone Mesh 2210 2232
? ? ? ? ? ? ? ? ? ?
On Sat, Feb 12, 2022 at 8:46 AM WA4TUX Dave < wa4tux@...> wrote: Hey Don,
I've picked up a couple of these on the US Amazon store:
73, de dave/WA4TUX
|
For 9600 Baud AX25, Yaesu recommends using a Deviation Meter to set the deviation. ?I get intermittent success with various sites and probably need to adjust my radio.
Does anyone have an idea for an inexpe
|
Re: Heads-up for Canadian Miady battery
Hey Don,
I've picked up a couple of these on the US Amazon store:
73, de dave/WA4TUX
|
Unless you changed the account name, it should be pi for username. ?Should also be your pi password.?
toggle quoted message
Show quoted text
I was able to ping the IP. I then was able to verify that VNC was enabled. Now I can¡¯t remember what username and password combo to use when settiup the vnc connection. I should remember but this one brain doesn¡¯t retain like it use to. I thought is was
pi-star then password. Nope. Tried raspberry pie then password. Nope. Then
pi@IP. Nope.?
Thanks for all the help! ?Where would this hobby be without such great Elmers like all if yoo! ?
73,
Dave
|
I was able to ping the IP. I then was able to verify that VNC was enabled. Now I can¡¯t remember what username and password combo to use when settiup the vnc connection. I should remember but this one brain doesn¡¯t retain like it use to. I thought is was pi-star then password. Nope. Tried raspberry pie then password. Nope. Then pi@IP. Nope.?
Thanks for all the help! ?Where would this hobby be without such great Elmers like all if yoo! ?
73,
Dave
|
Dave
First I would recommend adding a blank text file - ssh.txt -? then using putty or what have you on windows or terminal on macs. ssh into the build a pi, run "sudo raspi-config" turn on? VNC in? interfacing options and don't for forget to set VNC resolution in display option ,set it to a higher resolution to make sure you can read it on your remote screen. create a? "wpa_supplicant.conf " put it on the sd card's boot side . I will? add the layout here so you can copy and paste it. Hope this helps..
73,
Bill
N3VMT
?
ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=netdev
update_config=1
ap_scan=1
fast_reauth=1
country=Us
network={
?? ?ssid="phone hotspot name"
?? ?psk="Phone password here"
?? ?id_str="0"
?? ?priority=99
}
network={
?? ?ssid="Home network"
?? ?psk="home network password"
?? ?id_str="1"
?? ?priority=100
}
|
Another possible answer:? Sometimes when I boot my Pi it fails to recognize my Wifi so I have to wait until the Hospot timer tries again.? I set mine to 2 minutes.? Then it works as usual.? For some reason it turns on the hotspot on boot and I end up with a 10.10.10.10 address.? If you connect Ethernet at boot you can always come in on that address and see what is going on with Conky.? Your router might be hanging on to the old address (the way it should) as addresses are given a lease when they are assigned and that address will continue to be used as long as the device is used within the lease period.? Often youu can VNC into it using the hostname of the Pi, like vnc raspberrypi? try that.
|
Most obvious question: Did you enable VNC in raspi-config, Interfaces, VNC?
Kevin -- KD9EFV
|
Good evening All,
Created my first Build A Pi SD card last night.? Added a bunch of Jason's tools, Winlink, Direwolf, Hamclock, Conky etc.
I shut the Pi down last night, and returned this eveining learn more and add more to it.? Powered it up and can't VNC into.
I Go to my router and can see raspberrypi.? It has the same IP that it assigned to it last night.? But I cannot VNC into it.
Any help would be greatly appreciated.
73,
Dave
KB7BYI
|
Re: Latest Pat Winlink and rig contrl
#bap
Jason,
Something to note. The ARDOP PTT config is available in two locations in PAT Menu. One is in Manage PAt Winlink as you described before, the other is in Settings/Config. I had to make sure both were set to yes before my station would cooperate.
Chris, KI7JOM
|
Re: Js8call program features too large to use
#js8call
Just tried a few digferent resolutions again and its always the same with the js8 program. All the features are too large and wont match its window size like the terminal window. Terminal woll adjust sizing of letters amd numbers. Js8 is keeping all of its icons and things too massive to use.
|
Re: Js8call program features too large to use
#js8call
It seems like things like terminal frame are fine with me, just the js8 program.
|
Re: Js8call program features too large to use
#js8call
I'm having the same issue. My PI 3 A+ is nicely set up for my desktop or Toughbook. I tried to change the resolution?on the pad and it was a lost cause. I may have to get an Android phone terminal and ssh in and use sudo raspi-config to change the?resolution?that way.
73 Don Poaps
New Westminster, BC
VA7DGP DATA VA7QU ? VOICE Winlink: va7qu@...
Subject://wl2k ? ? ? ? ? ALLSTAR ?530780 Hamshack Hotline 5971 Mid-Island Phone Mesh 2210 2232
? ? ? ? ? ? ? ? ? ?
On Fri, Feb 11, 2022 at 8:49 AM Jacob Lindsey ( KN4YAV ) and Kayla Lindsey ( KO4DEG ) < jmlredtail@...> wrote:
Yea i set a few different resolutions and they dont affect the program features, just the entire resolution, which, size wise, im fine with.
Ill re-go over the higher res' again just to triple check though
|
Re: Js8call program features too large to use
#js8call
Yea i set a few different resolutions and they dont affect the program features, just the entire resolution, which, size wise, im fine with.
Ill re-go over the higher res' again just to triple check though
|
Re: Baofeng uv5r, Direwolf and YACC Not Transmitting
I¡¯ve never had any luck with any Chinese radios using VOX and anything packet, although the UV-5R and md380 are the only ones I¡¯ve tried. I ended up using my tnc-x TNC and creating my own cable. This worked great when I tried using Xastir but I haven¡¯t been able to do anything packet related for some time now. If a hardware TNC is feasible, here¡¯s the instructions to build a proper cable:
http://www.tnc-x.com/Baofeng.htm
Jay
73 de N0SR
|
AX.25 Port Configuration for Pat WInlink on Pi Zero
Hey all,
I followed Jason's "Pi Zero Project" videos to build a Pi Zero
headless setup. A great help for a newcomer to digital modes! No
problems with initial install of AX.25 or Pat. All command
responses followed the video exactly.
After shutting the Pi down and starting up the next day, I have
an error with AX.25 port configuration.
pi@pizero:~ $ pat connect
ax25:///WA6LIE-10
2022/02/10 21:33:10
Connecting to WA6LIE-10 (ax25)...
2022/02/10 21:33:10
Unable to establish connection to remote: No AX.25 ports
configured
My "axports" file shows one entry, equal to the output from:
"echo "wl2k $CALL 1200
255 7 Winlink" | sudo tee -a /etc/ax25/axports"
Output of "rfkill list"
pi@pizero:~ $ rfkill list
0: phy0: Wireless LAN
?? ?Soft blocked: no
?? ?Hard blocked: no
1: hci0: Bluetooth
??? Soft blocked: no
?? ?Hard blocked: no
I'm sure it's a step or connection I
missed. Has anyone seen this before? Thanks in advance!
Luke
KN6LAP
|
Don Poaps
Don
WA4TUX Dave
N3VMT
Jacob Lindsey ( KN4YAV ) and Kayla Lindsey ( KO4DEG )
JaySheepdog