Most obvious question: Did you enable VNC in raspi-config, Interfaces, VNC?

Kevin -- KD9EFV

Good evening All,
Created my first Build A Pi SD card last night.? Added a bunch of Jason's tools, Winlink, Direwolf, Hamclock, Conky etc.
I shut the Pi down last night, and returned this eveining learn more and add more to it.? Powered it up and can't VNC into.
I Go to my router and can see raspberrypi.? It has the same IP that it assigned to it last night.? But I cannot VNC into it.
Any help would be greatly appreciated.

73,
Dave
KB7BYI

Jason,

Something to note. The ARDOP PTT config is available in two locations in PAT Menu. One is in Manage PAt Winlink as you described before, the other is in Settings/Config. I had to make sure both were set to yes before my station would cooperate.

Chris, KI7JOM

Just tried a few digferent resolutions again and its always the same with the js8 program. All the features are too large and wont match its window size like the terminal window. Terminal woll adjust sizing of letters amd numbers. Js8 is keeping all of its icons and things too massive to use.

It seems like things like terminal frame are fine with me, just the js8 program.

Yea i set a few different resolutions and they dont affect the program features, just the entire resolution, which, size wise, im fine with.

Ill re-go over the higher res' again just to triple check though

I’ve never had any luck with any Chinese radios using VOX and anything packet, although the UV-5R and md380 are the only ones I’ve tried. I ended up using my tnc-x TNC and creating my own cable. This worked great when I tried using Xastir but I haven’t been able to do anything packet related for some time now. If a hardware TNC is feasible, here’s the instructions to build a proper cable:
http://www.tnc-x.com/Baofeng.htm

Jay
73 de N0SR

开云体育

Hi folks,
I'm having an issue with the Red Cross custom forms with in FLMSG.? You open them with the "Edit Form" button.? It opens the form in the browser opens, but after a few seconds it crashes in the browser and it says the site is unreachable.? It seems like it having trouble connecting to 127.0.0.1:8081 after the initial connection.

Multiple builds, multiple RPI.

Any ideas?

Have you set a higher resolution for VNC desktop in the pi configuration?

I recalled that I had a Signalink so I ordered a cable. I will report back here to confirm the PTT works.

I looked at the Digirig and it looks good. I plan to purchase that for another APRS system.

the same here. I run a raspi 4B also in an ARGON40 with with BAP on Bullseye. The distance argon40 to the router is only 1m, but I loose again and again wifi connection. This maybe after several hours of work but also maybe after half an hour. The time to reconnect also is quite different between 10secs to some minutes. I will look for a wifi dongle and try with this.Klaus, DC2JR

Kevin,

The same RPI4 in the same chassis did the BAP build with a WiFi connection.? Hours of downloads.

Never has a significant problem with the WiFi on this machine when running BAP builds on Buster and Buster based Ham-Pi.? Am sure the Argone case is part of the problem, but something in the BAP build pushed it over the edge.

Have run a temporary ethernet to the machine.? Will have to redo some cables to make the installation acceptable and more cat proof.? Hope it will allow VNC to run as well.

Mike

For Comparison, I put 32bit Bullseye on the card, updated, then did a full install of BAP

Everything installed on the first attempt, including FLDIGI

So there is something a little different with the way things are done with 32bit and 64bit Bullseye

One thing that I know is different is the update that shows up in 64bit after the first BAP install attempt. No matter what I did with 64 bit, I could not get it to show the update icon before the first BAP install attempt.

Thinking out loud, I am wondering if BAP gets installation of 32bit items, and then the update wants to update to 64bit for those things. I might be wrong (as I am often wrong :D ).

I was hoping anyone could help me out a bit.

Im getting portable digital operations ready and, in such, i have a pi 3b+ with js8call on it. The program loads up fine and seems ready to test; but, the features in the window are so large that it is unusable. I cant, for the life of me, figure this out.

I would really appreciate any help on the issue as Im hoping to be able to have this ready for a backpacking trip in a few months.

Thank you all
73

I have an ArgonOne V2 case. I love mine, but they do have an issue with reducing WiFi signal strength (google it). I have one set on it's side (it's headless anyway) with the bottom pointing in the general direction of the access point. Works somewhat better than flat. It's probably because of the extra mass pointing down to the CPU and WiFi chips.

Kevin -- KD9EFV

Did a full build w newest version of BAP on an RPI4 mounted in an ARGON40 enclosure with a 256gb SSD.? Everything went as well as one can hope for.? System worked on SD.? System worked on SSD.? 7100 works.? GPS a little slow to pick up enough satellites but that is not a BAP problem at all.? Kudos to Jason for making this easy.

Am seeing the WiFi dropping out much more than it has ever done.? Had it been this bad, the BAP build would never have run.? Argon fan is et to keep CPU temp to 55C or so.

Any thoughts other than running ethernet?? That would be a bit of a challenge.

Thank you!

Did a full install with the newest version of BAP.? Came up nicely.? Both monitors work.? GPS is a little slow to sync ... not a BAP problem.? Transferred the system to the SSDD of my Argon40 and system acted as it did on the SD card.

Am seeing the wi-fi dropping out.