开云体育

Thanks Dave, What's the story on the dual caps? Regards Gene Sent from my T-Mobile 5G Device Get Outlook for Android<https://aka.ms/AAb9ysg> ________________________________ Sent: Monday, November 22,

Here is a Mouser list I use: Mfr.: KEMET Mfr. #: A759MU277M1VAAE022 Mouser #: 80-A759MU277M1VAAE22 Desc.: Aluminum Organic Polymer Capacitors 35V 270uF 20% ESR=22mOhms RoHS Compliant 20 20 Ships Now

Not sure of the circuit - I would pull it from a place you are sure drives the Ghz synthesizer - OXO mist likely Quoting "Jared Cabot via groups.io" <jaredcabot@...>:

I have the Leo Bodnar GPS standard to compare against, should I pull the 5MHz from the front or rear panel of the 5065A, or directly from the OCXO module?

I too have a '532A that I'd like to re-home for a nominal sum, if anyone is interested. -Dave -- Dave McGuire, AK4HZ New Kensington, PA

If you have a '34 (that he doesn't buy) I'm interested Quoting "Precaud via groups.io" <jbau@...>:

Gene, seriously, check those capacitors on the power supply board. This is not just an occasional problem; seriously, 3/4ths of the 70900s that have gone through here have had that failure. -Dave --

I have a 16532A if that willl work for you. Will have to look to see if I have any 33's or 34's left.

Yes, I'll do that, thanks Bruce I just order the band 0 amplifier, a working and tested unit from eBay located in NJ. When it arrives, I'll redo several test and see the behavoir of the unit before

VFD? A search shows Variable Frequency Drive but since I have played with Nixies and Numitrons maybe it is Vacuum Fluorescent Display. I wish people would define the first instance of an acronym. Some

I am wondering what is behind the options 043 and W55 of my 8662A (S/N prefix 2936) and I would be glad if somebody is out there who could tell. Thanks! Chris

I don't know about VFDs, but I once ordered an LCD from Keysight with the same part number as the one I had which was damaged. The two LCDs looked quite different on the PCB, but had the same part

Hi Gene, I have a working unit and its setting is as show in attached photos. If you follow the same setting and 70900 still not show up then you may have hardware issue… I am just a normal user, if

Thanks Steve, The as-found is shown on the right…so I tried the settings in Figure 2.4 as shown below… still no cigar…70900A still MIA ON Map? Sent: Sunday, November 21, 2021 4:24 PM To:

Craig, Yeh that’s what I’m circling on also. Thanks for the manual. I’ve converted this to a text searchable document that you may find useful, see attachment. From what I understand at this

Hi Dave The formula is on the spec sheets I have referred to for example Equivalent series resistance (ESR) Calculated from tan δmax. and CR (see Table 2) ESR = tan δ/2 π f CR Also it could be we

What formula? -Dave -- Dave McGuire, AK4HZ New Kensington, PA

Exactly, and why there were two alternatives. I've heard both argued. if the number and amount of parts to be replaced is minimal, I'd go with #2, replace them all if on the other hand, replacing them

Hi Vladan The specs I looked at had a formula that I did not understand Regards Paul Sent: 22 November 2021 02:13 To: [email protected] Subject: Re:

Hi Vladan Thank you just going to bed it is 2:30 am hear Dues any one have an contacts at Sprague or Sangamo ? Best Regards Paul Sent: 22 November 2021 02:01 To: