开云体育

ctrl + shift + ? for shortcuts
© 2025 开云体育
  1. HP-Agilent-Keysight-Equipment
  2. Messages
Expanded Topics Messages
Date
Re: HP 1631D / HP 10271A / HP 10272A

[email protected]
 

--- In hp_agilent_equipment@..., Michael Lohmeyer
<mike@a...> wrote:
At 3:56 AM +0000 12/12/03, MauriceS_65 wrote:
Do you mean this pdf?
Yes. That's it. But...

The logic analyzer has the PODs. and they contain - as far as I can
see - 11 pin 0.156" Connectors...
I can get the grabbers, but I have not seen any sets for this
particular model...
The HP1631D is a different (older) unit than I thought. So,
my
advice isn't as applicable. Looking at the pictures in the two
auctions below, the probe tips aren't just simple wires. Note the
wires all go into a plastic block, which then attaches to the HP
10271A and HP 10272A boxes. You need these wires ends, right?
They
probably have some kind of RC network in them, like the pods
described in the PDF file above.
Probes leads are passive. You just need suitable 0.154" conector
block, wire and then connection to grabber.

I have just sold my 1630D on Ebay you can wee the home made leads in
the picture. Grabbers came from 1650 series and are relativly easy to
obtain.


ViewItem&item=2576377602&category=40004&rd=1

Richard



ViewItem&item=2581080559&category=25395

ViewItem&item=2580220769&category=25395


You might try contacting vendors that rent or sell used
equipment. These units are old enough that they may have a set
laying around which they are willing to sell for cheap.

Good luck. Sorry I wasn't much help.

Mike
--
----------------
Michael Lohmeyer
mike@a...
Re: HP Logic Analyzer Pods

 

In a message dated 12/13/2003 6:54:25 AM Eastern Standard Time, hp_agilent_equipment@... writes:


The logic analyzer has the PODs. and they contain - as far as I can see - 11 pin 0.156" Connectors...I can get the grabbers, but I have not seen any sets for this particular model...

Gentlemen:

You might try an MTA-156 IDC receptacle used for wire-to-board interconnection.? They are available for about $1.00 each.? The 12 position unit (you must trim off the extra "hole" with a Dremmel tool) is available from Newark Electronics as 15F1426.

Regards . . . Tom Leedy
Re: HP 1631D / HP 10271A / HP 10272A

 

At 3:56 AM +0000 12/12/03, MauriceS_65 wrote:
Do you mean this pdf?
Yes. That's it. But...

The logic analyzer has the PODs. and they contain - as far as I can
see - 11 pin 0.156" Connectors...
I can get the grabbers, but I have not seen any sets for this
particular model...
The HP1631D is a different (older) unit than I thought. So, my advice isn't as applicable. Looking at the pictures in the two auctions below, the probe tips aren't just simple wires. Note the wires all go into a plastic block, which then attaches to the HP 10271A and HP 10272A boxes. You need these wires ends, right? They probably have some kind of RC network in them, like the pods described in the PDF file above.






You might try contacting vendors that rent or sell used equipment. These units are old enough that they may have a set laying around which they are willing to sell for cheap.

Good luck. Sorry I wasn't much help.

Mike
--
----------------
Michael Lohmeyer
mike@...
Re: HP 1631D / HP 10271A / HP 10272A

MauriceS_65
 

Hello Mike,

To understand better how your 1631D cables are wired and how
you
can use them, look for the PDF file manual on Agilent's web site
about interconnect solutions or grabber solutions for HP/Agilent
logic analyzers. Sorry, I forget the exact name, but it's a manual
that explains all the different pod sets and grabbers that HP
sells.
The manual is continually updated for the current equipment, but
most
of it is still applicable to the older logic analyzers. It shows
the
pinout and electrical characteristics of the cable ends (without
pods) as well as the electrical characteristics for the pods. If
you
get desperate, let me know and I can probably dig up the manual for
you.
Do you mean this pdf?


The logic analyzer has the PODs. and they contain - as far as I can
see - 11 pin 0.156" Connectors...
I can get the grabbers, but I have not seen any sets for this
particular model...

Thanks,

Maurice
Re: HP 1631D / HP 10271A / HP 10272A

 

At 5:47 PM +0000 12/11/03, MauriceS_65 wrote:
I have a 1631D with all the Pods, but missing grabbers... And finding
affordable kits has been impossible...
Keep an eye out on ebay. Every now and then, someone puts up a set of grabbers (just grabbers without the pods) and they tend to go for about $20 per set of 20 grabbers. Of (just in case I misunderstand), if you need the pods as well, they also come up on ebay a lot (more often than just the grabbers). My definition of pods is the part that attaches to the end of the long ribbon cable, and has the loose wires coming out the end (GND, clock, and 16 data leads). The grabbers would then attach to the loose wires. Complete pod sets (pods, grabbers, ground leads, etc.) seem to go for about $30-$40 per pod, or $120-$160 a set of 4, on ebay. I just picked up a brand new set of 4, never opened for the low end of that price.

To understand better how your 1631D cables are wired and how you can use them, look for the PDF file manual on Agilent's web site about interconnect solutions or grabber solutions for HP/Agilent logic analyzers. Sorry, I forget the exact name, but it's a manual that explains all the different pod sets and grabbers that HP sells. The manual is continually updated for the current equipment, but most of it is still applicable to the older logic analyzers. It shows the pinout and electrical characteristics of the cable ends (without pods) as well as the electrical characteristics for the pods. If you get desperate, let me know and I can probably dig up the manual for you.




Is it possible to make grabbers myself? I thought the Pods have MTA
156 connectors.. And maybe I can make them..
You can also buy grabbers from any of a number of different places that sell wires and things (like banana plugs, lab interconnect wire, meter and scope test leads, etc.). They won't be exactly the same as the original HP grabbers, but they may be acceptable for your needs, or you might even find better grabbers (though, probably for a much higher price). Anyway you look at it, though, grabbers are expensive.

I just finished buying pods and grabbers for my logic analyzer. I had to buy 12 pod sets. Ugh! Luckily, I got better than average deals for them on ebay, but it still adds up quickly.

Mike
--
----------------
Michael Lohmeyer
mike@...
3586C COMMANDS?

 

My usual plea.......anybody have a list of 3586c commands? (I never get
manuals with my stuff)...


Thanks to all who replied regarding the peeling meters and all..

73

Tom
HP 1631D / HP 10271A / HP 10272A

MauriceS_65
 

I have a 1631D with all the Pods, but missing grabbers... And finding
affordable kits has been impossible...

Is it possible to make grabbers myself? I thought the Pods have MTA
156 connectors.. And maybe I can make them..


Thanks,

Maurice
HP 4952A software copy protection?

Richard
 

Hi All

I have obtained some software for the 4952A protocol Analyser. These
have been copied using the LIFUTIL utility. However wheras the data
files work fine the applications (things like a VT100 emulator) give
an error "Application Denied". I suspect and have read somthing about
this being some HP copy protection.


Can anyone help or make any suggestions?

Many Thanks

Richard
Re: Seeking Manual for HP 204B Oscillator

 

I have a manual for 204C. If that would do, I can send you schematic; manual
is too many pages to scan. Even better, the whole manual is on BAMA site (
); that site has limited number of simultaneous
log-ons, so you might have to try several times.


Regards

Miroslav Pokorni

----- Original Message -----
From: <leedyt@...>
To: <hp_agilent_equipment@...>
Sent: Monday, December 01, 2003 1:35 PM
Subject: [hp_agilent_equipment] Seeking Manual for HP 204B Oscillator




Does anyone have an e-mailable manual (or at least a schematic) for an HP
204B Oscillator. It would be sincerely appreciated.

Tom Leedy
Clarksburg, MD
Returned mail: User unknown

 

The original message was received at Tue, 2 Dec 2003 22:35:50 0800

----- The following addresses had permanent fatal errors -----
<greg_werstiuk@...>

----- Transcript of session follows -----
... while talking to pop3.email.msn.com:
RCPT To:<greg_werstiuk@...>
<<< 550 <greg_werstiuk@...>... User unknown
550 <greg_werstiuk@...>... User unknown
Re: Seeking Manual for HP 204B Oscillator

Greyhawk
 

开云体育

Hello, Did You Try Bama. They Have A Few HP Manuals.
?
Greyhawk
?

----- Original Message -----
From: leedyt@...
Sent: Monday, December 01, 2003 16:35
Subject: [hp_agilent_equipment] Seeking Manual for HP 204B Oscillator



Does anyone have an e-mailable manual (or at least a schematic) for an HP 204B Oscillator.? It would be sincerely appreciated.

Tom Leedy
Clarksburg, MD

To unsubscribe from this group, send an email to:
hp_agilent_equipment-unsubscribe@...



Your use of Yahoo! Groups is subject to the .

Seeking Manual for HP 204B Oscillator

 



Does anyone have an e-mailable manual (or at least a schematic) for an HP 204B Oscillator.? It would be sincerely appreciated.

Tom Leedy
Clarksburg, MD
Re: Manual for HP428A Clip on DC Milliammeter

 

Hi Sam,


I have the PDF manual for a 428B model if that will
help.

Regards,

Jim

--- sreaves22655 <sreaves@...> wrote:
Anyone have an emailable copy of the HP 428A?

Sam
W3OHM



__________________________________
Do you Yahoo!?
Free Pop-Up Blocker - Get it now
Manual for HP428A Clip on DC Milliammeter

sreaves22655
 

Anyone have an emailable copy of the HP 428A?

Sam
W3OHM
Re: Still looking for 3580A knobs?

 

--- In hp_agilent_equipment@..., Charles <charlesmorris@d...> wrote:
My 3580A spectrum analyzer works great but is much in need of a
set of knobs. All the large ones with labeled "skirts" are either
broken or missing entirely/replaced with nonlabeled knobs. Any
leads appreciated.
thanks
Charles
Have you asked sphere?



he hasn't those knobs in his list yet, but to ask him is always wise



Jorgen
dj0ud
Still looking for 3580A knobs?

Charles
 

My 3580A spectrum analyzer works great but is much in need of a
set of knobs. All the large ones with labeled "skirts" are either
broken or missing entirely/replaced with nonlabeled knobs. Any
leads appreciated.
thanks
Charles
schematics for HP54721 4G amplifier scope plug-in?

 

Greetings -

After searching the excellent lists from tbfowler,
came up dry. Looking for service lit/schematics (have
the operating manual) for this HP54720D scope 4G amp plug-in
designated HP54721. The cal output on the plug-in is not
working, i can visually trace but, much better to have
schematics, board is multi-layer and I don't have
extenders.

Thanks!
Re: Schematic for HP651B

 

Hi Scott,

That would be great. Thank you so much

Mitch

--- In hp_agilent_equipment@..., "Scott" <scott@m...>
wrote:
Hi Mitch,



I have a 451B service manual somewhere. When I find it I'll be
happy to scan
the schematics and send them to you.



Scott





_____

I've stopped 3,696 spam messages. You can too!
One month FREE spam protection at www.cloudmark.com
<>
<>



-----Original Message-----
From: aquaman8_2001 [mailto:aquaman8_2001@y...]
Sent: Friday, November 14, 2003 12:37 AM
To: hp_agilent_equipment@...
Subject: [hp_agilent_equipment] Schematic for HP651B



Hello All,

I am in need of the power supply and oscillator schematics for an
HP
651B I am repairing. I have a service manual but it is for an older
model than mine. My unit has a serial number of 811-03132.

Can anyone help me out with a scan of the 2 foldout pages for this
oscillator? I would really appreciate it. It is not significantly
different from the older unit, but it appears that Si transistors
replace the Ge units seen in the manual I have. To make matters
worse, someone has been in there and made some changes/repairs that
appear to be less than professional! Not sure anymore what are
original parts and which have been changed! The parts pages which
describe thea transistors and diodes used would also be helpful.

Any help would be appreciated.

Thanks,

Mitch






Yahoo! Groups Sponsor



ADVERTISEMENT

<
egroup
web/S=1705083663:HM/EXP=1068874649/A=1853618/R=0/*http:/www.netflix.co
m/Defa
ult?mqso=60178338&partid=4116730> click here



<
M=267637.4116730.5333196.1261774/D=egroupmai
l/S=:HM/A=1853618/rand=921768773>


To unsubscribe from this group, send an email to:
hp_agilent_equipment-unsubscribe@...



Your use of Yahoo! Groups is subject to the Yahoo!
<> Terms of Service.
HP3336 failure

 

Hello all,
I'm looking for an Hewlett Packard component, for my HP3336B
generator.
It is marked as "1SB1 0021".
Could you please help me to find this component?
Thanks for your courtesy
Best regards
Marcello Pellerano - ITALY
Re: Schematic for HP651B

Scott
 

开云体育

Hi Mitch,

?

I have a 451B service manual somewhere. When I find it I’ll be happy to scan the schematics and send them to you.

?

Scott

?

?

I've stopped 3,696 spam messages. You can too!
One month FREE spam protection at


-----Original Message-----
From: aquaman8_2001 [mailto:aquaman8_2001@...]
Sent: Friday, November 14, 2003 12:37 AM
To: hp_agilent_equipment@...
Subject: [hp_agilent_equipment] Schematic for HP651B

?

Hello All,

I am in need of the power supply and oscillator schematics for an HP
651B I am repairing. I have a service manual but it is for an older
model than mine. My unit has a serial number of 811-03132.

Can anyone help me out with a scan of the 2 foldout pages for this
oscillator? I would really appreciate it. It is not significantly
different from the older unit, but it appears that Si transistors
replace the Ge units seen in the manual I have. To make matters
worse, someone has been in there and made some changes/repairs that
appear to be less than professional! Not sure anymore what are
original parts and which have been changed! The parts pages which
describe thea transistors and diodes used would also be helpful.

Any help would be appreciated.

Thanks,

Mitch



To unsubscribe from this group, send an email to:
hp_agilent_equipment-unsubscribe@...



Your use of Yahoo! Groups is subject to the .


150661 - 150680 of 150760