开云体育

And what is the point I missed? If service is done by legit repair lab or Keysight, S/N does not change and it will always be matching. Alltest you linked is a legit unit with everything mathing up

Hello Illya You misunderstand the point! In some cases they interchange mainframes-front-panel and processor boards!You are that in some cases hostid and serial nr doesn’t matc-they don’t care to

Hello Hardy, EXT is E6607B : https://www.keysight.com/us/en/product/E6607B/ext-wireless-communications-test-set.html They are obviously legit Agilent/Keysight hardware and components, including

Hi I am not sure I understand your statement!! These MXA`s are genuie Agilent/keysight N9020A analyzers-These resellers did get many and some were obviously a mix of mainframe and processor board.If

I've got mine few years back. They get lot of EXT units when upgraded their cell tower base station test labs to newer and faster equipment. EXT is essentially MXA hardware with different personality

What the bulb is doing is limiting the current into the equipment.? All the voltages will be low. What this is useful for is 1) saving fuses 2) running things at reduced input voltages which,

All, I finally obtained a proper bulb -- turns out, my GF had an unopened package of 2 60 watt incandescent bulbs. Woo hoo. Finally got the bulb connected after removing the fuse holder. HOWEVER, now,

As an update, the HP80K system boot disk creation went well using Stan's files pointers and an old PC. The mainframe itself appears to have some power supply issues - it'll run briefly and then lock

Welcome, Leo!? I know I've seen your name before; are you on the TekScopes group?? That's a nice HPAK gear collection you have.? Unfortunately I can't help you with your 54620C.? I had a 54504A

Hello, I have a question related to the 8510C and more specifically related to the Display Unit 85101C. I noticed that there are 2 memory cards with the same part number 85101-60238 but they are not

Hi Leo, Welcome to the Group! Unfortunately, I can't help you with your 'scope problem because I'm not familiar with the HP 54620C.I do remember that we met around 10 years ago at your place where I

Hi. I'm new to this group and thought a little introduction is in order. I am a semi-retired EE, specialized in the design of RFID readers which I have been doing for the past 30+ years. Not a

And I now own a 4338B, so I'm now looking for the adjustment Programs for the 4263B and the 4338B (Part number: 04338-65005).... Jared

That's when you want to use an isolation transformer... -- Member of the toughest, meanest, deadliest, most unrelenting -- and ablest -- form of life in this section of space, ?a critter that can be

Stan, Thanks for the help!? I'll try creating the boot disks tonight - I have an older PC with a disk controller that still works with LIFUTIL (as well as an HPIB ISA adapter & external 9122C drive),

Peter Better give me a picture! Hardy -----Oprindelig meddelelse----- Fra: [email protected] <[email protected]> P? vegne af Peter Gottlieb Sendt: 23.

Hi Yes-sure they are from ATE racks-mobile test. Regarding cosmetics one have to be very cautious-some do not look well,Ask for specific pictures of the unit,not just a -sample!!! The seller I use can

Rifa caps is a good preventative maintenance but the issue is most likely a small startup capacitor near the controller IC. These dry out and will not have the correct voltage feeding the controller

I've got an HP 8920B in very good physical condition (except for a couple of scratches on the top, it almost looks new).? So it doesn't look like it's been out in the field much, if ever. I purchased

The 310VDC on the bulk caps are present even during the click, dipping only to 295V when click is heard. Measured them and they look fine to. So probably not the problem. I've just check the primary