开云体育

Hi Guys, Yes, I have the manual!? The problem was my failure to comprehend what the words right in front of me (yep, on page 9) were saying!? Brain fart/old age setting in? Can't wait to build up

Hi Robert, The referenced description can be found here: this can be copied: /g/HBTE/files/WA2FZW - M0WID ESP32 - ILI9341 Version of the TinySA/Tiny SA Operator's Manual (V2.8).pdf --

Maybe you didn't get as far as page 9! After the library is installed, you need to copy the files: M0WID_Setup_ILI9341_TinySA.h WA2FZW_Setup_ILI9341_TinySA.h from the "TFT_eSPI Setup Files" folder

Thank you both David and John. All good now! Where I went wrong was I put all three files in the C:\Users\Bob A. Booey\Documents\Arduino\libraries\TFT_eSPI\User_Setups directory when the

David should have included the "User_Setup_Select.h" file in the TFT setup files he posted the other day. Here's a copy set up correctly. Without the correct (M0WID) setup file being selected, the

This is the sort of error that comes up when the TFT_eSPI user setup is not 100% correct. First of all find your TFT_eSPI library folder.? In your case it seems to be C:\Users\Bob A.

P.S. Downgraded to TFT_eSPI V2.2.0 as mentioned in the manual rather than V2.2.6, no difference.

Hi Elia, I believe I have properly followed the steps in both the posts you mentioned, thanks. I found that if I uncomment the "//? TouchCalibrate ();??? ??? ??? ??? ??? ??? //

Hi Robert, Seems you may have the same issue I had indeed. See post #1381 & #1431 further below, that solved the tft problem for me. For the wifi, see post #1387 below. Once I did both fixes the

Am I experiencing the same thing?? Probably not as compiling is not completing without errors.? I am using just a ESP32 WROVER board, trying to load the code for now, I have not yet built the TSA

Hi Dave, I remembered setting up User_Setup_Select.h, checking it and missing the entry. I just replaced it, then I also set up WiFi and it works fine. I am very happy about it. It can be built

I posted a zip file for the TFT_eSPI user setup into the files section.? Sorry these files were missed from the last release. However you have a display working, so you already have the TFT_ESPI

The following files have been uploaded to the Files area of the [email protected] group. * /WA2FZW - M0WID ESP32 - ILI9341 Version of the TinySA/TFT_eSPI Setup Files.zip (

Hi Dave, Thanks for the information, I hope I won't forget about the newer firmware. I think I found the reason the User_setup_select was missing the link. Maybe it's because of it. I'll try. Where

Well done!? In the Arduino IDE, under tools there is a command to Upload Data to the ESp32.? Make sure you have your serial monitor closed first, then select.? The contents of the data subfolder in

hi, I managed to install the missing parts yesterday and turned it on today. I get a yellow alert when I log in: "Failed to mount SPIFFS Use ESP sketch Data Upload in the Arduino IDE WiFi Disabled "

Mouser list the 3555 but have no stock and the part is 'obsolete'. eBay have them as below but currently not shipping. I did find a wholesaler who deals in old stock but he's not answering email

There were at least others discussed too... If I recall right, someone went through the Digikey and/or Mouser catalog and basically put together a list of possibilities. Then a number of people

Hi Bill, I did try searching but did not find much.? Just did another and dug in a little more, the closest thing I could find was this thread: /g/HBTE/topic/69385413#675 where the

There was a whole thread on this very thing. You can search for it. There are substitutes… Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ Owner - Operator Big Signal