开云体育

re, *in boot log you have:* TGIF Si4432 Good to go? - regRead = 03 _cs = 2? Type 8 Version 6 Status 20 End of Init - _cs = 2 TGLO Si4432 Good to go? - regRead = 03 _cs = 25? Type 8 Version 6

Re, 1)? you wrote:? If you have installed the SI4432 for the tracking generator then make sure #define TG_IF_INSTALLED and TG_LO_INSTALLED and TG_ATT_INSTALLED are not commented out in the same

Hello Gerard, I guess your issues, to get the Web Server running, are related to missing upload of the "data" subdirectory (under your sketch folder) into the SPIFFS file system on the ESP32. You will

Hello, thank you for your answer I’m going to test this afternoon I thought it created a new Wi-Fi network and we had to connect to it, but in fact I understood that it’s the opposite, it’s ESP

Hi Gerard. You are making good progress, well done. I have not had chance to look into the SPIFFS.begin() issue.? I guess the ESP32 libraries have been updated and the function now works in a

re, I have tried to put SPIFFS.begin(true), it's same to work.... but an other error et no WIFI cdt ....... Connecting... Connecting to: yourSSID Connection Failed! WebSockets started Building

Some issue here? pb of bootloader? E (588) SPIFFS: mount failed, -10025 · Issue #638 · espressif/arduino-esp32 · GitHub ( https://github.com/espressif/arduino-esp32/issues/638 ) what to do exactly?

Hello, *I have no screen at this time.* I installed the latest version of Arduino 2.04 I had to install several librairies because not present in the simpleSA_011.zip file By dint of patience the

Hello, This morning, i try to made a compilation i think have the solution in an other post for using a IL9341 screen and how to? resold the compilation error? "TFT_eSPI.h: No such file or

*Hello* *i need some help to put the software in thr ESP:* Tell me if this is good or if I comment a mistake. I think we first have to decompress the SimpleSA_011.zip file Then do we need to do

Hello Erik, Thank's for the retur i will look that I’m only at the beginning of my tests For now nothing uploaded in ESP It is seen in the WIFI network, it is already a good point I have to go back

The simplest first test is if you can see the zero Hz peak. E .g. If the RX module can see the output of the LO as it leaks through the mixer. -- HBTE Files section: /g/HBTE/files

Hello, thank's for your answer For now I have not yet received the IL screen. I have another screen but I believe based on XT2046, I do not know if it can work. Unless I try a Wi-Fi connection with

I think the best test is to try the signal generator and the tracking generator in signal generator mode. Connect the sa connection on the simpleSa to your oscilloscope ideally with a 50 ohm

Hello, My PCB is practically completely wired. I have a nanovna, a 200mhz 4-way oscilloscope, a 60MHz FY6900 generator. My question is how to test the differents modules depending on the schématic. I

re, I started removing components on mini pcb S4432. In fact, I have a very thin cutter that I grinded to cut the memory legs. So I cut the component in half, a little bit of flow, and I cut off the

Hello, There, I was busy troubleshooting a digital oscilloscope and I had set aside this SimpleSA. Now the oscilloscope works and so I started cabling my board that I had modified, to actually put it

Hi, I used 20.000 MHz ?20 pF crystals from Digikey. part number 631-1091-ND Purchased in January 2019z tbey are made in China, Fox Electronics. the first one I used worked in the oscillator. i tuned

I didn't go further. The current status is HF, and there is still a resonance point of - 80dbm. LF can be used, but I can see a frequency point of 215MHz occasionally. However, when I move the LCD

Hello Blackberryer, More news.? Have you made any progress in assembling your analyzer? For now I’m busy on oscilloscope troubleshooting, so not doing much about it. cdt