Hello,
I have no screen at this time.
I installed the latest version of Arduino 2.04
I had to install several librairies because not present in the simpleSA_011.zip file
By dint of patience the compilation is passed
but no WIFI view, (but blue light)? whereas before I saw an ESP32? on the discovery WIFI
?
Here is the result in the serial monitor on the first boot
there is a mistake on the wifi
How many librairie?
Others errors?
??
cdt
rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:1
load:0x3fff0018,len:4
load:0x3fff001c,len:1044
load:0x40078000,len:10124
load:0x40080400,len:5856
entry 0x400806a8
?TX Si4432 Good to go? - regRead = 03 _cs = 5? Type 8 Version 6 Status 20?
End of Init - _cs = 5
?RX Si4432 Good to go? - regRead = 03 _cs = 4? Type 8 Version 6 Status 20?
End of Init - _cs = 4
Bytes got = 0 - aiming for 456.? No bandpass filter calibrations saved? ? ? ? ? ? ?-------> think Normal
Bandpass Filter Calibration values:
?
filter: 0, rbw10=26 , cal=0.000000?
filter: 1, rbw10=28 , cal=0.000000?
filter: 2, rbw10=31 , cal=0.000000?
filter: 3, rbw10=32 , cal=0.000000?
filter: 4, rbw10=37 , cal=0.000000?
filter: 5, rbw10=42 , cal=0.000000?
filter: 6, rbw10=45 , cal=0.000000?
filter: 7, rbw10=49 , cal=0.000000?
filter: 8, rbw10=54 , cal=0.000000?
filter: 9, rbw10=59 , cal=0.000000?
filter: 10, rbw10=61 , cal=0.000000?
filter: 11, rbw10=72 , cal=0.000000?
filter: 12, rbw10=82 , cal=0.000000?
filter: 13, rbw10=88 , cal=0.000000?
filter: 14, rbw10=95 , cal=0.000000?
filter: 15, rbw10=106 , cal=0.000000?
filter: 16, rbw10=115 , cal=0.000000?
filter: 17, rbw10=121 , cal=0.000000?
filter: 18, rbw10=142 , cal=0.000000?
filter: 19, rbw10=162 , cal=0.000000?
filter: 20, rbw10=175 , cal=0.000000?
filter: 21, rbw10=189 , cal=0.000000?
filter: 22, rbw10=210 , cal=0.000000?
filter: 23, rbw10=227 , cal=0.000000?
filter: 24, rbw10=240 , cal=0.000000?
filter: 25, rbw10=282 , cal=0.000000?
filter: 26, rbw10=322 , cal=0.000000?
filter: 27, rbw10=347 , cal=0.000000?
filter: 28, rbw10=377 , cal=0.000000?
filter: 29, rbw10=417 , cal=0.000000?
filter: 30, rbw10=452 , cal=0.000000
filter: 31, rbw10=479 , cal=0.000000?
filter: 32, rbw10=562 , cal=0.000000?
filter: 33, rbw10=641 , cal=0.000000?
filter: 34, rbw10=692 , cal=0.000000?
filter: 35, rbw10=752 , cal=0.000000?
filter: 36, rbw10=832 , cal=0.000000?
filter: 37, rbw10=900 , cal=0.000000?
filter: 38, rbw10=953 , cal=0.000000?
filter: 39, rbw10=1121 , cal=0.000000?
filter: 40, rbw10=1279 , cal=0.000000?
filter: 41, rbw10=1379 , cal=0.000000?
filter: 42, rbw10=1428 , cal=0.000000?
filter: 43, rbw10=1678 , cal=0.000000?
filter: 44, rbw10=1811 , cal=0.000000?
filter: 45, rbw10=1915 , cal=0.000000?
filter: 46, rbw10=2251 , cal=0.000000?
filter: 47, rbw10=2488 , cal=0.000000?
filter: 48, rbw10=2693 , cal=0.000000?
filter: 49, rbw10=2849 , cal=0.000000?
filter: 50, rbw10=3355 , cal=0.000000?
filter: 51, rbw10=3618 , cal=0.000000?
filter: 52, rbw10=4202 , cal=0.000000?
filter: 53, rbw10=4684 , cal=0.000000?
filter: 54, rbw10=5188 , cal=0.000000?
filter: 55, rbw10=5770 , cal=0.000000?
filter: 56, rbw10=6207 , cal=0.000000?
TGIF Si4432 Good to go? - regRead = 03 _cs = 2? Type 8 Version 6 Status 20?
End of Init - _cs = 2
?TGLO Si4432 Good to go? - regRead = 03 _cs = 25? Type 8 Version 6 Status 20?
End of Init - _cs = 25
E (2653) SPIFFS: mount failed, -10025? ? ? ? ? ? ? ? ? ? ? ? ? ? ------> Here error, so no WIFI??? Why??
SPIFFS Mount Failed
?
WiFi not enabled!
?
?
simpleSA Version 0.11 Initialization Complete
?
simpleSA Spectrum Analyzer Version 0.11 - User Commands:
?
Sweep Settings:
?
? ? START.........Sweep start frequency, currently: 0 Hz
? ? STOP..........Sweep stop frequency, currently:? 100,000,000 Hz
? ? CENTER........Sweep center frequency, currently: 50,000,000 Hz
? ? SPAN..........Sweep frequency span, currently:? 100,000,000 Hz
? ? MARKER........It's complicated; read the documentation!
? ? FOCUS.........Set single frequency mode with narrow bandwidth
? ? RBW...........Set or get resolution bandwidth (RBW); currently: 2.6 KHz
? ? ATTEN.........Set or get the attenuator setting; currently: 0dB
? ? EXTGAIN.......Set or get the external gain setting; currently: 0dB
? ? SPUR......... Turn Spur Reduction 'ON' or 'OFF'; currently: OFF
? ? PAUSE.........Pause or resume the sweep
?
Mode selection:
?
? ? SALO..........Set to analyse mode low frequency range
? ? SGLO..........Set to signal generator mode low frequency range
? ? IFSWEEP.......Set to IF Sweep mode to analyse the TinySA SAW filters
? ? RXSWEEP.......Set to RX Sweep mode to analyse the TinySA FIR filters
? ? BANDSCOPE.....Set to BANDSCOPE mode
? ? OTA...........Set to OTA update mode to download firmware or SPIFFS over wifi
?
Display Options:
?
? ? TRACES........Turn display traces on or off ['GAIN' or 'dB']
? ? PREAMP/GAIN...Set or get the receiver preamp gain
? ? ? ? ? ? ? ? ? See documentation for allowed values
GRIDREF.......Set the grid reference level; currently: -10dB
? ? SCALE.........Set the dB/horizontal line value; currently: 10dB
? ? WFMIN.........Set the minimum RSSI level for waterfall colouring: 17
? ? WFGAIN........Set the gain for waterfall colouring: 0
?
Signal Generator Commands:
?
? ? SGON..........Turn on signal generator output
? ? SGOFF.........Turn off signal generator output; currently 0
? ? SGFREQ........Signal Generator frequency, currently: 14,000,000 Hz
? ? SGLODRIVE.....Local oscillator drive level in signal generator mode [0 to 7]; currently: 6
? ? SGRXDRIVE.....RX SI4432 oscillator drive level in signal generator mode [0 to 4]; currently: 3
Tracking Generator Commands:
?
? ? TRACKON.......Turn on tracking generator output
? ? TRACKSIG......Turn on tracking generator signal generator output
? ? TRACKOFF......Turn off tracking generator output; currently 0
? ? TGLODRIVE.....Local oscillator drive level in tracking generator mode [0 to 7]; currently: 6
? ? TGIFDRIVE.....Local oscillator drive level in tracking generator mode [0 to 7]; currently: 3
? ? TGOFFSET......Tracking generator offset from SA IF; currently: 0
? ? TGFREQ........Tracking generator signal generator frequency; currently: 14000000
?
Other Commands:
?
? ? DRIVE.........Local oscillator drive level [0 to 7]; currently: 6
? ? SAVE .........Save the current scan configuration [0 to 4]
? ? RECALL........Recall a saved scan configuration [0 to 4]
? ? FREQ..........Set or get the frequency for the selected VFO
? ? HELP (or ?)...Show this menu
? ? STEPS.........Sweep samples; currently: 290
DELAY.........Timestep in uS, currently: 6800uS
? ? OFFDEL........Timestep in uS for Bandscope, currently: 5000uS
? ? VFO...........Set or get active VFO [R, ( L or T ), I(tg If), G(tG LO)]; currently: RX (0)
?
Debugging and Troubleshooting Commands:
?
? ? IF_FREQ.......Set the IF (receiver) frequency [433 to 435MHz]; currently: 433,920,000 Hz
? ? REGDUMP.......Display a dump of all the registers for the selected VFO
? ? RSSI..........Output RSSI readings until the 'Q' command is entered
? ? ? ? ? ? ? ? ? or one time only ['C' or '1']; the default is once.
? ? QUIT (or Q)...Terminate RSSI output
? ? REGISTER......Read or write a Si4432 register for the selected VFO
? ? REF_FREQ......Set or get the transmitter GPIO2 reference frequency
? ? TUNE..........Tune the frequency of the selected VFO
? ? ACTUAL_PWR....Calibrate the indicated power level
? ? CONFIG_SAVE...Save the hardware configuration parameters
? ? WiFiTIME......Target web page Chart Update time interval in ms
? ? WiFiPTS.......No of points in each data chunk pushed to the web clients
? ? SKTINT........Interval between check for websocket messages if no client connected
? ? IFSIGNAL......Frequency of signal injected for IF Sweep (External or Ref)
? ? BPFCAL........Start SI4432 bandpass filter calibration - RXSweep mode only
weepLo dBadjust = -120.000000; leveloffset = 0.000000; attenuate = 0, ext gain = 0.000000, bpfCal = 0.000000
?
?
END
?
Gerard