开云体育

Good progress. The message indicates an issue with the SPI communication to the SI4432.? This is most likely to be wiring again, but could also be the SI4432 module itself.? There were some posts

I finally got the proper pinout completed and simpleSA boots up on screen, but errors out with "TX Si4432 Reset failed - _cs = 5", I had run across a post about this before but can not find it with

Dave, I am in usa, ohio, and I use an exacto knife to make my own traces on blank 2 sided pc board. A tedious and time consuming task, but I have constructed many fairly complex boards, albeit mainly

John - well done for wanting to make your own version and having a go.? Much more satisfaction at the end than just buying something and not understanding how it works, but also at times frustrating!

Thank you Dave, no, they are not same pinouts, the schematic I have is for esp32 wrover t8 1.7, the schematic you just sent is for esp32_devkit_v1_doit. I attached a copy of the one I have, so you can

Hi John. Sorry to hear you are still having trouble.? It may be my fault for not updating the pinout descriptions in the code comments - at work again so cannot easily check. Lets start by making

Sorry to post again about the esp32 t8. The compiling works flawlessly, but could only get white screen on lcd, Followed advice from Bodmer about the tft-espi examples and ran the " user setup

Thank you, Dave, it compiled this time ok. And thanks for all the time and effort involved and the software. John

Hi John. It is wet and miserable here today so I took the time to update my ESP32 core, Arduino libraries and Arduino IDE to the latest versions to see if I could replicate your problem, and I

Dave, I have a dell laptop with Dave, I have a laptop with I5 processor, 4 gbyte memory, 1 tbyte? hd, running windows 10 pro, I just installed arduino 1.8.9 for the first time and went through boards

Dave, I always install all boards through boards manager, in fact the url has changed to? ( https://raw.githubusercontent.com/espressif/arduino-esp32/gh-pages/package_esp32_index.json). I just

Did you install the ESP32 boards using the boards manager or some other way?? Certainly your PC is more modern and capable than my ancient i5, so nothing to do with the hardware.? I do use windows

David, I had quite a few errors which I had to correct and they all were caused by the ide not finding the file in the place expected. It took me a while to read back through the error report to find

Interesting.? Again I am at work, but took a quick look through your error log.? It seems like your compiler/linker is using the standard arduino wifi class rather then the specific one for ESP32. I

David, I downloaded the last version you posted "0.15", and after correcting several not found files, making sure they were in the library where expected, I recompiled and now get this error "pcnt was

Hi John. I am at work at the moment, and will not have time to look tonight, maybe tomorrow. I have a vague recollection that the touch library is only loaded if TOUCH_CS and/or SPI_TOUCH_FREQUENCY

I posted this on tinysa group and was advised to post here. I compiled the example of wifi scan and uploaded it to the esp32 wrover t8 1.7 without any errors, and it ran with no problems. So the

I have built the analyzer per dave M0WID design, tried to compile the arduino sketch for it version 1.4 , have corrected all errors so far (esp32 libraries were not loaded correctly by boards

Hello, All file reading problems are fixed. you needed a version 6 of Kicad This is what they call build of night(?) At least it works https://forum.kicad.info/t/pb-version-kicad/32266/3 thank you

Just re-read your post and noted the wish for an offset for the TG.? I will add that to the list of things to look at - it may happen over the xmas break - it may not.? Good idea. 73 Dave M0WID