开云体育

To Kevin Monceaux, Please see third reply in this thread. There is link to restored tape with source code library dataset. Best wishes, Andre

JJ, It don't think it will work, unless someone has found a way to work around the OSAM appendage issue. If I remember correctly, the OSAM appendage is incompatible with MVS, and the source code

Following on from my post dated December 13th, I had a spare hour this evening, and I downloaded the "The DL/I" system (AKA, I believe, IMS/360); I did the stage 1 and stage 2 sysgen to install the

In MVS TK5 refer to SYS1.SYSGEN.CNTL(IOGEN) Cheers, Rob

<dwegscheid@...> wrote: Out of curiosity, once edited that member EDT00 wat is the next step for it to be recognized? Just a reboot? TIA. Roxo -- ---------------- Non

Um,?the authors names are on the first page of the manual…..

Hi all, Not sure who manages/updates the TK5-Introduction-and-User-Manual, but Step 13 on page 17, says to run "S RAFKUSER after updating SYS1.SECURE.CNTL.? The correct procedure name is

I believe Jay has it as a separate download. I have a Jay based build with it installed. On Sat, Dec 23, 2023 at 4:37 AM, cjar1950 via groups.io<cjar1950@...> wrote: Rene, I

Rene, I also find it on TK3, TK3UPD and TK4.. but not on Jay's based builds. Chris --

That command is available on TK4- (Update 8) and TK5 (Update 2), the systems mentioned in the original post. It is not a standard TSO command, so it may not be available on other distributions (Jay's

Hi René, May you add more informations ? IKJ56500I COMMAND UNITS NOT FOUND Thanks, René

In the version of TK4- Update 8, which I'm using, before I move to TK5 Update 2, I found them in SYS1.SYSGEN.CNTL(IOGEN) # SYSDA=DISK=SYSSQ is all DASD # PAGE is 160-16F, 260-26F, 360-36F # SORT is

The TSO command UNITS will display current group names with their members. Cheers, Rene FERLAND, Montreal

Also, additional names can be defined by the DYNAMASK utility, usually gets its input from sys1.parmlib(EDT00). On Fri, Dec 22, 2023 at 7:46 PM, Mike Schwab<Mike.A.Schwab@...> wrote: It

It is part of site installation. SYS1.SYSGEN.CNTL (sysgen01) seems to be the location, per jay ,moseley's instructions. netscape.net@groups.io> wrote: -- Mike A Schwab, Springfield IL USA Where do

I know of UNIT=TAPE, or UNIT=3350, but DASD group names elude me. Over the years I've seen SYSDA, WORK, DASD, and others. Where do I look to find the group names that are used in the TK4- and TK5

Hello! To quote, :"I agree!". At first I would collect the source code for Hercules and work out how to build it to work inside my Slackware Linux setup. For a while earlier, during a specific

This packaging may be the key to getting some distros to actually deliver Hercules v4. ?The ones that do provide the packaged version is, as Drew Derbyshire mentions, Hercules v3. There has not been

On Thu, Dec 21, 2023 at 11:13 AM, Vince Coen wrote:> If you visit #hercules-helper-script on https://discord.gg/S6bdUbDsMQ then Bill @wrljet can most likely help.

I have updated my Linux distro from Mageia v8 to v9 and helper fails badly during the build. Even the TK5-v2 has its problems. Most annoying. Vince