|
Hallo everybody, Last night I received a called from one partner in the Observatory asking me for a problem with the Gemini 2... Hand Control showing "Connecting to Gemini".. I don?t understand because after reprogramation the Gemini worked propperly, I tested it several times and it looked good.. Tomorrow I will try to confirm that my partner did a propper connection... but if really exists this problem again.. I won?t understand it.. As prevention I will do a new SD ram with the firmware for the Main Board, as I did it last week.. The only reason that I would understand is a problem with the SD.. any advice? 搁别苍é, have you fixed the problem with the "latitude sign".. Regards ? Miguel Angel
Pérez Hernández
Alpha Cygni S.L.
c/ San Agustín, 23
38410 - Los Realejos
S.C. de Tenerife
Islas Canarias - Espa?a
Tlf/fax: 0034 922 34 30 38
? ?nete a Betacygni, la trastienda: ?
|
Hallo Miguel,
Last
night I received a called from one partner in the Observatory asking me
for a problem with the Gemini 2... Hand Control showing "Connecting to
Gemini".. I don?t understand because after reprogramation the Gemini
worked propperly, I tested it several times and it looked good..
Tomorrow I will try to confirm that my partner did a propper
connection... but if really exists this problem again.. I won?t
understand it..
Can you tell us what has been done? Is it the same Gemini board? Is the
correct port used, its baud rate for the HC (57k) set, ...
As
prevention I will do a new SD ram with the firmware for the Main Board,
as I did it last week.. The only reason that I would understand is a
problem with the SD.. any advice?
The SD card should be freshly formatted at the start.
搁别苍é,
have you fixed the problem with the "latitude sign"..
Yes, and added a lot of things. Alas, I was busy all day, I'm just back
at the PC. I'll have to remove some tiny bugs, most is already working
fine.
搁别苍é
|
Hallo 搁别苍é, It is the same Gemini and Hand Control that I reprogrammed the last Friday. I checked it again on Saturday morning, and all worked good.. I?m not very sure what happened, I will check it tomorrow. About the baud rate for the HC (57k) set... How can I check this?.. But, this is not a value that can change momentarily, not?.. I try to say, if I checked it and it worked ... then it has to work if any changes has been done?.. Regards ? Miguel Angel Pérez Hernández
Alpha Cygni S.L.
c/ San Agustín, 23
38410 - Los Realejos
S.C. de
Tenerife
Islas Canarias - Espa?a
Tlf/fax: 0034 922 34 30 38
? ?nete a Betacygni, la trastienda: ?
De: Rene Goerlich
Para:
Gemini-II@...
Enviado: jue,24 febrero, 2011 18:25
Asunto: Re: [Gemini-II] Latitude bug.. fixed??
?
Hallo Miguel,
Last
night I received a called from one partner in the Observatory asking me
for a problem with the Gemini 2... Hand Control showing "Connecting to
Gemini".. I don?t understand because after reprogramation the Gemini
worked propperly, I tested it several times and it looked good..
Tomorrow I will try to confirm that my partner did a propper
connection... but if really exists this problem again.. I won?t
understand it..
Can you tell us what has been done? Is it the same Gemini board? Is the
correct port used, its baud rate for the HC (57k) set, ...
As
prevention I will do a new SD ram with the firmware for the Main Board,
as I did it last week.. The only reason that I would understand is a
problem with the SD.. any advice?
The SD card should be freshly formatted at the start.
搁别苍é,
have you fixed the problem with the "latitude sign"..
Yes, and added a lot of things. Alas, I was busy all day, I'm just back
at the PC. I'll have to remove some tiny bugs, most is already working
fine.
搁别苍é
|
Miguel
You set the baud rates for the serial ports using the Web inteface.
Goto the Serial link and set serial port 1 to 57600 baud.
Tom Hilton
On 2/24/2011 11:49 AM, Miguel Angel Pérez Hernández wrote:
toggle quoted message
Show quoted text
?
Hallo 搁别苍é,
It is the same Gemini and Hand Control that I reprogrammed
the last Friday. I checked it again on Saturday morning,
and all worked good.. I?m not very sure what happened, I
will check it tomorrow.
About the baud rate for the HC (57k) set... How can I
check this?.. But, this is not a value that can change
momentarily, not?.. I try to say, if I checked it and it
worked ... then it has to work if any changes has been
done?..
Regards
?
Miguel
Angel Pérez Hernández
Alpha Cygni S.L.
c/ San Agustín, 23
38410 - Los Realejos
S.C. de Tenerife
Islas Canarias - Espa?a
Tlf/fax: 0034 922 34 30 38
?
?nete a Betacygni, la
trastienda: ?
De:
Rene Goerlich
Para:
Gemini-II@...
Enviado:
jue,24 febrero, 2011 18:25
Asunto:
Re: [Gemini-II] Latitude bug.. fixed??
?
Hallo Miguel,
Last
night I received a called from one partner
in the Observatory asking me
for a problem with the Gemini 2... Hand
Control showing "Connecting to
Gemini".. I don?t understand because after
reprogramation the Gemini
worked propperly, I tested it several
times and it looked good..
Tomorrow I will try to confirm that my
partner did a propper
connection... but if really exists this
problem again.. I won?t
understand it..
Can you tell us what has been done? Is it the same
Gemini board? Is the
correct port used, its baud rate for the HC (57k)
set, ...
As
prevention I will do a new SD ram with the
firmware for the Main Board,
as I did it last week.. The only reason
that I would understand is a
problem with the SD.. any advice?
The SD card should be freshly formatted at the
start.
搁别苍é,
have you fixed the problem with the
"latitude sign"..
Yes, and added a lot of things. Alas, I was busy all
day, I'm just back
at the PC. I'll have to remove some tiny bugs, most
is already working
fine.
搁别苍é
|
PS
There may be some confusion here, as the Faceplate on the Gemini 2
is labeled Serial Port 1, Graphics HC and Serial Port 2, Graphics
HC, while the Web interface refers to them as Serial port 0 and
Serial port 1.?? The webs Serial port 1 = the Gemini Serial port 2,
which is the one that you should be using.
Tom Hilton
On 2/24/2011 11:56 AM, tom@... wrote:
toggle quoted message
Show quoted text
?
Miguel
You set the baud rates for the serial ports using the Web
inteface.
Goto the Serial link and set serial port 1 to 57600 baud.
Tom Hilton
On 2/24/2011 11:49 AM, Miguel Angel Pérez Hernández wrote:
?
Hallo 搁别苍é,
It is the same Gemini and Hand Control that I
reprogrammed the last Friday. I checked it again on
Saturday morning, and all worked good.. I?m not very
sure what happened, I will check it tomorrow.
About the baud rate for the HC (57k) set... How can I
check this?.. But, this is not a value that can change
momentarily, not?.. I try to say, if I checked it and
it worked ... then it has to work if any changes has
been done?..
Regards
?
Miguel
Angel Pérez Hernández
Alpha Cygni S.L.
c/ San Agustín, 23
38410 - Los Realejos
S.C. de Tenerife
Islas Canarias - Espa?a
Tlf/fax: 0034 922 34 30 38
?
?nete a
Betacygni, la trastienda: ?
De:
Rene Goerlich
Para:
Gemini-II@...
Enviado:
jue,24 febrero, 2011 18:25
Asunto:
Re: [Gemini-II] Latitude bug.. fixed??
?
Hallo Miguel,
Last night
I received a called from one partner
in the Observatory asking me for a
problem with the Gemini 2... Hand
Control showing "Connecting to
Gemini".. I don?t understand because
after reprogramation the Gemini worked
propperly, I tested it several times
and it looked good.. Tomorrow I will
try to confirm that my partner did a
propper connection... but if really
exists this problem again.. I won?t
understand it..
Can you tell us what has been done? Is it the
same Gemini board? Is the correct port used, its
baud rate for the HC (57k) set, ...
As
prevention I will do a new SD ram with
the firmware for the Main Board, as I
did it last week.. The only reason
that I would understand is a problem
with the SD.. any advice?
The SD card should be freshly formatted at the
start.
搁别苍é, have
you fixed the problem with the
"latitude sign"..
Yes, and added a lot of things. Alas, I was busy
all day, I'm just back at the PC. I'll have to
remove some tiny bugs, most is already working
fine.
搁别苍é
|
Ok Tom...thanks I will chek it tomorrow.. and let you know Regards ? Miguel Angel Pérez Hernández
Alpha Cygni S.L.
c/ San Agustín, 23
38410 - Los Realejos
S.C. de Tenerife
Islas Canarias - Espa?a
Tlf/fax: 0034 922 34 30 38
? ?nete a Betacygni, la trastienda: ?
De: "tom@..." <tom@...>
Para: Gemini-II@...
Enviado: jue,24 febrero, 2011 19:03
Asunto: Re: [Gemini-II] Latitude bug.. fixed??
?
PS
There may be some confusion here, as the Faceplate on the Gemini 2
is labeled Serial Port 1, Graphics HC and Serial Port 2, Graphics
HC, while the Web interface refers to them as Serial port 0 and
Serial port 1.?? The webs Serial port 1 = the Gemini Serial port 2,
which is the one that you should be using.
Tom Hilton
On 2/24/2011 11:56 AM, tom@... wrote:
?
Miguel
You set the baud rates for the serial ports using the Web
inteface.
Goto the Serial link and set serial port 1 to 57600 baud.
Tom Hilton
On 2/24/2011 11:49 AM, Miguel Angel Pérez Hernández wrote:
?
Hallo 搁别苍é,
It is the same Gemini and Hand Control that I
reprogrammed the last Friday. I checked it again on
Saturday morning, and all worked good.. I?m not very
sure what happened, I will check it tomorrow.
About the baud rate for the HC (57k) set... How can I
check this?.. But, this is not a value that can change
momentarily, not?.. I try to say, if I checked it and
it worked ... then it has to work if any changes has
been done?..
Regards
?
Miguel
Angel Pérez Hernández
Alpha Cygni S.L.
c/ San Agustín, 23
38410 - Los Realejos
S.C. de Tenerife
Islas Canarias - Espa?a
Tlf/fax: 0034 922 34 30 38
?
?nete a
Betacygni, la trastienda: ?
De:
Rene Goerlich
Para:
Gemini-II@...
Enviado:
jue,24 febrero, 2011 18:25
Asunto:
Re: [Gemini-II] Latitude bug.. fixed??
?
Hallo Miguel,
Last night
I received a called from one partner
in the Observatory asking me for a
problem with the Gemini 2... Hand
Control showing "Connecting to
Gemini".. I don?t understand because
after reprogramation the Gemini worked
propperly, I tested it several times
and it looked good.. Tomorrow I will
try to confirm that my partner did a
propper connection... but if really
exists this problem again.. I won?t
understand it..
Can you tell us what has been done? Is it the
same Gemini board? Is the correct port used, its
baud rate for the HC (57k) set, ...
As
prevention I will do a new SD ram with
the firmware for the Main Board, as I
did it last week.. The only reason
that I would understand is a problem
with the SD.. any advice?
The SD card should be freshly formatted at the
start.
搁别苍é, have
you fixed the problem with the
"latitude sign"..
Yes, and added a lot of things. Alas, I was busy
all day, I'm just back at the PC. I'll have to
remove some tiny bugs, most is already working
fine.
搁别苍é
|
