开云体育

GEO 210 Probe budget kit

Michael C All Messages By This Member #8 hi.. got the probe kit.? Do you have a clip to attach the red wire to the round connection on a LND 7311 sensor??? all I got was the red wire, couple of resistors, shrink wrap ...?? as for mechanicals and mounting the lnd7311 in the housing -? the 3 brackets hold it down - have to punch holes through the foam gasket for the screws - that seems intuitive.? The kit included nuts and washers I see no use for ??? Also, the bracket hole at the bottom six o'clock position is right where the LND 7311 stem will be.? I'm guessing twist the probe around a bit and have the LND stem a bit off of six o'clock so that mounting screw/bracket can fit.?? thanks
[email protected] All Messages By This Member #9 yes that should be there, can you show mea picture of the parts you found so far? ?George? toggle quoted message Show quoted text From: "MT" <mtcooper01@...> To: "GEOelectronics" <[email protected]> Sent: Friday, May 8, 2020 8:49:42 PM Subject: [GEOelectronics] GEO 210 Probe budget kit hi.. got the probe kit.? Do you have a clip to attach the red wire to the round connection on a LND 7311 sensor??? all I got was the red wire, couple of resistors, shrink wrap ...?? as for mechanicals and mounting the lnd7311 in the housing -? the 3 brackets hold it down - have to punch holes through the foam gasket for the screws - that seems intuitive.? The kit included nuts and washers I see no use for ??? Also, the bracket hole at the bottom six o'clock position is right where the LND 7311 stem will be.? I'm guessing twist the probe around a bit and have the LND stem a bit off of six o'clock so that mounting screw/bracket can fit.?? thanks
[email protected] All Messages By This Member #10 yes the probe sits sort of sideways. toggle quoted message Show quoted text From: "MT" <mtcooper01@...> To: "GEOelectronics" <[email protected]> Sent: Friday, May 8, 2020 8:49:42 PM Subject: [GEOelectronics] GEO 210 Probe budget kit hi.. got the probe kit.? Do you have a clip to attach the red wire to the round connection on a LND 7311 sensor??? all I got was the red wire, couple of resistors, shrink wrap ...?? as for mechanicals and mounting the lnd7311 in the housing -? the 3 brackets hold it down - have to punch holes through the foam gasket for the screws - that seems intuitive.? The kit included nuts and washers I see no use for ??? Also, the bracket hole at the bottom six o'clock position is right where the LND 7311 stem will be.? I'm guessing twist the probe around a bit and have the LND stem a bit off of six o'clock so that mounting screw/bracket can fit.?? thanks MVC-019S.jpg MVC-021S.jpg Probe day1.jpg
Michael C All Messages By This Member #13 sorry if you have already answered this..? the GEO 210 probe kit included two resistors.? Not sure the value, they appear the same.? a) I assume I only need one of them. b) where does the one resistor go??? Is it inline from the BNC connector center pin with the red wire to the LND clip??? thanks
[email protected] All Messages By This Member #14 1 resistor. The other is spare, both same 3.3 Meg Ohms. Goes in series with center pin from BNC to the clip. Ludlum solders the resistor right to the clip, then the wire to the other end of the resistor, so I do it that way. George? toggle quoted message Show quoted text ----- Original Message ----- From: Michael C <mtcooper01@...> To: [email protected] Sent: Fri, 15 May 2020 18:58:27 -0400 (EDT) Subject: Re: [GEOelectronics] GEO 210 Probe budget kit sorry if you have already answered this..? the GEO 210 probe kit included two resistors.? Not sure the value, they appear the same.? a) I assume I only need one of them. b) where does the one resistor go??? Is it inline from the BNC connector center pin with the red wire to the LND clip??? thanks
Michael C All Messages By This Member #15 开云体育 Thank you.. that is what I thought, just wanted to make sure.?? ? toggle quoted message Show quoted text From: [email protected] <[email protected]> On Behalf Of GEOelectronics@... Sent: Friday, May 15, 2020 5:27 PM To: [email protected] Subject: Re: [GEOelectronics] GEO 210 Probe budget kit ? 1 resistor. The other is spare, both same 3.3 Meg Ohms. ? Goes in series with center pin from BNC to the clip. Ludlum solders the resistor right to the clip, then the wire to the other end of the resistor, so I do it that way. ? George? ? ? ----- Original Message ----- From: Michael C <mtcooper01@...> To: [email protected] Sent: Fri, 15 May 2020 18:58:27 -0400 (EDT) Subject: Re: [GEOelectronics] GEO 210 Probe budget kit ? sorry if you have already answered this..? the GEO 210 probe kit included two resistors.? Not sure the value, they appear the same.? a) I assume I only need one of them. b) where does the one resistor go??? Is it inline from the BNC connector center pin with the red wire to the LND clip??? thanks ? ? ? ?
Michael C All Messages By This Member #16 开云体育 Up and running.? I ended up putting the resistor at the BNC connector and shrink wrapping the crud out of that end for strain relief purposes. Then I pigtail loop under and around to the LND terminal with other end of wire soldered to the clip.? It’s a tight squeeze.?? This little thing kicks butt ??? ? toggle quoted message Show quoted text From: [email protected] <[email protected]> On Behalf Of GEOelectronics@... Sent: Friday, May 15, 2020 5:27 PM To: [email protected] Subject: Re: [GEOelectronics] GEO 210 Probe budget kit ? 1 resistor. The other is spare, both same 3.3 Meg Ohms. ? Goes in series with center pin from BNC to the clip. Ludlum solders the resistor right to the clip, then the wire to the other end of the resistor, so I do it that way. ? George? ? ? ----- Original Message ----- From: Michael C <mtcooper01@...> To: [email protected] Sent: Fri, 15 May 2020 18:58:27 -0400 (EDT) Subject: Re: [GEOelectronics] GEO 210 Probe budget kit ? sorry if you have already answered this..? the GEO 210 probe kit included two resistors.? Not sure the value, they appear the same.? a) I assume I only need one of them. b) where does the one resistor go??? Is it inline from the BNC connector center pin with the red wire to the LND clip??? thanks ? ? ? ?

Previous Topic Next Topic