开云体育

ctrl + shift + ? for shortcuts
© 2025 Groups.io
Date

Re: Stripes on display

 

开云体育

Hello All,

?

So far, my 857 keeps on tick’n, however, we used to utilize some old industrial power monitors that developed stripes on the lcd displays and found that if the Zebra strips were just replaced, the displays would work without the stripes.? Zebra strips are used in place of wire conductors between the glass Indium conductors of the actual LED display and the PCB that drives it.?

?

Fluke meters a while back also had the same problem.? I’ve had to get them replaced on my 87 from time to time.? Age tends to shrink the Zebra strips so the contact will become intermittent.

?

This link is the first page that showed up on Google.? I don’t represent the company or its products in anyway.

?

Zebra strips:

?

?

Your mileage may vary though.

?

--jeff

Wb7aht


Re: CAT update blocked during TX

 

开云体育

And, if I'm not mistaken, you're supposed to keep transmissions very short when working satellites.

Get


Re: Stripes on display

 

This is what it looks like inside the FT-857 Display Panel


Re: Stripes on display

 

Zack,
The short answer is, NO, there's no EASY way to solve this problem, except replacement of the assembly.
Here's the longer answer, and the reason why.
The failure is a poor or decaying soldered connection between the display screen and its mating circuit board, inside the control panel. To the best of my knowledge, no actual parts have failed, so replacement of components shouldn't be necessary.
HOWEVER, re-soldering the pads requires a fairly complex set of soldering skills, and likely, specialized equipment. Not a trivial job, certainly not quick and easy.

Do some searching, and you'll find lots of other threads about this around the Web, and huge amounts of mis-information and superstition-based answers.
Good luck sorting it all out!


Stripes on display

 

I am sure this has been asked before, but is there a fairly easy way to get rid of a few vertical stripes on the FT957 display? The seem to come and go.

73, Zack W9SZ


Re: CAT update blocked during TX

 

Hy. I Had the Same,...
After master reset. Everything was fine...

Check ist Out..

Good luck
Andy DF1HF


--
Diese Nachricht wurde von meinem Android Mobiltelefon mit GMX Mail gesendet.


Re: CAT update blocked during TX

 

Peter: This behavior for several Yaesu radios (857, 817, 897) is mentioned in the SatPC32 documentation.? (Hints->Yaesu, see the Reame(Yaesu).txt file).? Manual tuning (front panel) works, but CAT-controlled Doppler correction disabled when PTT pressed. Recommendation is to keep transmissions short, especially when Doppler shift changing rapidly.

73 Steve KS1G?


Re: CAT update blocked during TX

 

Yes that is a limitation of the 857 when using for satellite operation.? It really isn't a big problem if you keep your transmissions short.

Don K9AQ


Re: CAT update blocked during TX

 

Hello Yono,
I tried it here, and indeed, the 857 will not accept frequency change commands by CAT during transmit. I am pretty sure the CAT interface itself functions, as I use CAT command to switch between transmit and receive. So I guess it is designed this way.

73
Peter/PA3FQH


CAT update blocked during TX

 

Dear all,
While qso with a friend that uses a FT-857 thru a linear satellite, I noticed he always drifts upwards. He said GQRX was not updating the freq while TX and he has to release the PTT button between syllables so the radio catches up.

Is this a known bug (CAT port is disabled during TX), or the CT-62 cable got RF interference during TX.

Let me know your thoughts,

73 de Yono - YD0NXX


Re: Quickly change power levels

Michael Dannhardt
 

Thank you everyone. I learned a few things. I'll pass the info on to my Dad.

73,
Mike / KA4CDN


<Announcement> 2M 440MHz added to the 100W 10-80M loop

 

There is now a 2M & 440MHz loop integrated into the model 100W 10-80M MagLoop. A most excellent choice for the 857 that also supports VHF UHF & HF.?

Steve, N0TES
Founder, ?


Re: Quickly change power levels

 

Thank you I learned something

-----Original Message-----
From: [email protected] [mailto:[email protected]] On Behalf Of Leonard K. Pennock
Sent: Friday, July 9, 2021 8:36 AM
To: [email protected]
Subject: Re: [FT-857] Quickly change power levels

Grounding the brown wire in the power connector would drop maximum
output to 10W.

Leonard K. Pennock
AD7AS

Those who walk bravely through life, unafraid of loss or failure,
find that they very rarely lose or fail.

On 7/9/21 5:21 AM, Michael Dannhardt wrote:
Hi. My Dad has a FT-857d and has recently installed an external
amplifier which needs a drive level of around 20W. So we are looking for
a convient (fast) way to switch the rig from full power out (100w) to a
lower level.

I thought the A/B stacked VFO would work but it doesn't seem to save the
power level per VFO.

Any ideas? FWIW - he has the fancy mic with all the buttons.

Tnxs for any thoughts,
Mike / KA4CDN


Re: Quickly change power levels

 

You should be able to program one of the screen menu buttons (Menu 065 - 067) or the mic buttons (068 - 070) as RF power set (Menu 075).? It would make it easy to quickly bring up that setting.


Re: Quickly change power levels

 

144 MHz: 20W
430 MHz: 10W
with the brown wire.

73
Alfred - DJ0GM


Re: Quickly change power levels

 

I did that, but put the grounding wire on a switch

Mick SA4MDN


Re: Quickly change power levels

 

Grounding the brown wire in the power connector would drop maximum output to 10W.

Leonard K. Pennock
AD7AS

Those who walk bravely through life, unafraid of loss or failure,
find that they very rarely lose or fail.

On 7/9/21 5:21 AM, Michael Dannhardt wrote:
Hi. My Dad has a FT-857d and has recently installed an external amplifier which needs a drive level of around 20W. So we are looking for a convient? (fast) way to switch the rig from full power out (100w) to a lower level.
I thought the A/B stacked VFO would work but it doesn't seem to save the power level per VFO.
Any ideas? FWIW - he has the fancy mic with all the buttons.
Tnxs for any thoughts,
Mike / KA4CDN


Quickly change power levels

Michael Dannhardt
 

Hi. My Dad has a FT-857d and has recently installed an external amplifier which needs a drive level of around 20W. So we are looking for a convient? (fast) way to switch the rig from full power out (100w) to a lower level.

I thought the A/B stacked VFO would work but it doesn't seem to save the power level per VFO.

Any ideas? FWIW - he has the fancy mic with all the buttons.

Tnxs for any thoughts,
Mike / KA4CDN


Re: Another newbie question - programming frequencies

 

Eric,

I must be losing my mind.... I've got this thread being started by VK2DHV (who according to the ACMA database is David).

All good - Stay safe.

Cameron?



----- Original Message -----
From:
FT-857@groupsio

To:
<[email protected]>
Cc:

Sent:
Thu, 8 Jul 2021 14:42:40 +1000
Subject:
Re: [FT-857] Another newbie question - programming frequencies


Hi Cameron,

?

Stuart is the person who originally asked the question! Simple ACMA lookup.

?

73….Eric VK2VE.

?

From: [email protected] <[email protected]> On Behalf Of Cameron McKay
Sent: Wednesday, 7 July 2021 15:24
To: [email protected]
Subject: Re: [FT-857] Another newbie question - programming frequencies

?

Eric, Zak et al (although I'm not sure who Stuart is)...

?

?
This legal situation is actually much more onerous than it appears on the surface - hence why my response included specific reference to the Act (an Australian legislative document found ) and the applicable clauses.? Even being in possession, especially if the rig was made capable of transmission on those frequencies (even if only programmed as 'receive only') would like be deemed as 'with intent to operate'. If the radio was found to be functional (and especially given that the question has been asked in a pseudo-public forum) then there would be little in the way of a 'defence' (I can think of one but I'm not placing it into the public domain).? This is a specific issue I have asked our National Representative Body to have addressed in future revisions of the legislative instruments.

73,

?

Cameron


----- Original Message -----

?

To:

<[email protected]>

Cc:

?

Sent:

Wed, 7 Jul 2021 14:18:44 +1000

Subject:

Re: [FT-857] Another newbie question - programming frequencies

Hi Zack,

?

Agreed, however, Stewart was also mentioning about transmitting using the radio hence Compton’s, and my, comments about its none type approval here in Australia. One of the requirements for type approval here for non amateur band equipment is that it not be programmable, on transmit, from the front panel.

?

73….Eric VK2VE.

?

From: [email protected] <[email protected]> On Behalf Of Zack Widup
Sent: Wednesday, 7 July 2021 13:33
To: [email protected]
Subject: Re: [FT-857] Another newbie question - programming frequencies

?

Yes, but if he wants to listen to various frequencies? without having to tune to them each time, the rig will accept any frequency in its range for receive only. I am never going to transmit on LF NDB frequencies or AM BCB frequencies, but I have quite a few of those programmed into the radio with CHIRP.

?

73, Zack W9SZ

?

On Tue, Jul 6, 2021 at 9:24 PM Compton <comptonallen@...> wrote:

Although technically possible your amateur rig, FT 857, will never be permitted to Tx on those commercial frequencies, sorry, you will need a commercially approved radio.

--
Compton
VK2HRX
Sydney, Australia

?


This email has been checked for viruses by Avast antivirus software.

?




This email has been checked for viruses by Avast antivirus software.



Re: Another newbie question - programming frequencies

 

开云体育

Hi Cameron,

?

Stuart is the person who originally asked the question! Simple ACMA lookup.

?

73….Eric VK2VE.

?

From: [email protected] <[email protected]> On Behalf Of Cameron McKay
Sent: Wednesday, 7 July 2021 15:24
To: [email protected]
Subject: Re: [FT-857] Another newbie question - programming frequencies

?

Eric, Zak et al (although I'm not sure who Stuart is)...

?

?
This legal situation is actually much more onerous than it appears on the surface - hence why my response included specific reference to the Act (an Australian legislative document found ) and the applicable clauses.? Even being in possession, especially if the rig was made capable of transmission on those frequencies (even if only programmed as 'receive only') would like be deemed as 'with intent to operate'. If the radio was found to be functional (and especially given that the question has been asked in a pseudo-public forum) then there would be little in the way of a 'defence' (I can think of one but I'm not placing it into the public domain).? This is a specific issue I have asked our National Representative Body to have addressed in future revisions of the legislative instruments.

73,

?

Cameron


----- Original Message -----

?

To:

<[email protected]>

Cc:

?

Sent:

Wed, 7 Jul 2021 14:18:44 +1000

Subject:

Re: [FT-857] Another newbie question - programming frequencies

Hi Zack,

?

Agreed, however, Stewart was also mentioning about transmitting using the radio hence Compton’s, and my, comments about its none type approval here in Australia. One of the requirements for type approval here for non amateur band equipment is that it not be programmable, on transmit, from the front panel.

?

73….Eric VK2VE.

?

From: [email protected] <[email protected]> On Behalf Of Zack Widup
Sent: Wednesday, 7 July 2021 13:33
To: [email protected]
Subject: Re: [FT-857] Another newbie question - programming frequencies

?

Yes, but if he wants to listen to various frequencies? without having to tune to them each time, the rig will accept any frequency in its range for receive only. I am never going to transmit on LF NDB frequencies or AM BCB frequencies, but I have quite a few of those programmed into the radio with CHIRP.

?

73, Zack W9SZ

?

On Tue, Jul 6, 2021 at 9:24 PM Compton <comptonallen@...> wrote:

Although technically possible your amateur rig, FT 857, will never be permitted to Tx on those commercial frequencies, sorry, you will need a commercially approved radio.

--
Compton
VK2HRX
Sydney, Australia

?


This email has been checked for viruses by Avast antivirus software.

?




This email has been checked for viruses by Avast antivirus software.