开云体育

Menu #46 selects low frequency cutoff.? Menu #47 selects high frequency cutoff. Or, multifunction row "p", mash and hold the DBF softkey. Operating Manual page 30. 73, Mike N5MJ

Agreed on the difference it made.? ?I think I'll try turning it on and off in various modes to see its effects. Another learning moment. Dennis N1TEN? On Sun, Jun 7, 2020 at 6:59 AM, ROBERT

It was posted in small print & I overlooked it. Im surprised the AGC Made that much difference. Thanks. Bob, W7SCY

Sorry i thought it was posted.? Short version is the AGC was turned off and RF gain needed adjustment. Probably most of the problem was related to the AGC being off. Dennis N1TEN? On Sat, Jun 6,

What was the solution? I didsn’t see it on here. I had the opposite problem when my mode mysteriously changed to AM while I was on FM. Bob, W7SCY Sent from Robert's iPad 2

Good catch! ? It was off. That improved signal even more than messing with RF Gain knob. Thanks to all for the teaching moment. Dennis? N1TEN

Make sure AGC is on

Gents, Thanks so much for your suggestions. ?? I just found out that the RF Gain was not right for the AM broadcast signal level.? I must have adjusted it during SSB operations, when moving from FM

You are correct I did a bad typo. ? Not FM for sure.? Sorry. I am seeing AM on the radio display. DennisN1TEN

Mike,Menu item # please so I am on the same page. ? Dennis N1TEN

Did you mean... not FM for sure?Bob wa7dxzSent from my Verizon, Samsung Galaxy smartphone

Jason, I've had this with mine as well.? One instance was a sketchy fuseholder (the inrush current I-squared-R loss dropped the input voltage below 11.5VDC). Was the car running and VDC > 13 VDC at

Dennis, Check the receive bandwidth - AM broadcasts are often "wider" than SSB settings.? If I listen to AM I jack the low limit to 200 hz, and the high limit to 5khz. 73, Mike N5MJ

690 Khz, 760 khz and 1070 khz Dennis N1TEN? On Sat, Jun 6, 2020 at 9:25 AM, Tony VA7TF, VE7ACF<20junk20@...> wrote: #yiv7496658882 #yiv7496658882 -- _filtered {} _filtered {} _filtered {}

I'm saying that the 1070 AM staion is low and distorted as are three others local to? San Diego. I didn't think of non-broadcast AM.? I'll try it. Dennis N1TEN? On Sat, Jun 6, 2020 at 9:40 AM, Tony

1070 kHz is on the AM band Los Angeles. Is it a typo or you are definitely saying 1070 is not on AM? Try listening to WWV on 5, 10, 15 or 20 MHZ on SSB and AM. Is the AM signal clean? If so, then

Not a silly question, but not AM for sure.? ?1070 KNX in LA for example. from Yahoo Mail on Android On Sat, Jun 6, 2020 at 9:23 AM, Tony VA7TF, VE7ACF<20junk20@...> wrote: #yiv9770609097

What frequencies are programmed into the radio, or what are the frequencies in MHZ are you trying to listen to? --------------- Regards, Tony Sent: June 6, 2020 8:29 AM To: [email protected] Subject:

Silly question, are you listening to FM stations on AM? --------------- Regards, Tony VA7TF Sent: June 6, 2020 8:29 AM To: [email protected] Subject: Re: [FT-857] AM Broadcast Stations Distorted Noise

Noise blanker was off.? ? On Sat, Jun 6, 2020 at 5:56 AM, Dennis Yard via groups.io<hamandrovers@...> wrote: Theo, I'll check but I think I ran thru the DSP operations to check