Thanks for the info on the tool post from Amazon, did you have to do any mods for this or is it just a bolt on and go? Thanks
toggle quoted message
Show quoted text
On Nov 21, 2023, at 12:11 PM, Ccoggswell <Ccoggswell@...> wrote:
? Thanks for the input I’m going to get one of those tool posts And I have #37!!!!!
On Nov 21, 2023, at 11:00?AM, Dennis Turk <dennisturk448@...> wrote:
? Also note there is a spacer under the tool post on the Lot 5. You should not need this on your Lot 2. Lot 2 lathes were built in 1913 and are six inch swing lathes where later lathes in this series were 7 1/4 swing.? As to parts I have a few Lot 2 parts left from two parts lathes I have.. As to a tool post the OXA size quick change tool post is your best bet.? I have used this size tool post on my Lot 5 as well as my Dalton Lot 6 lathe with great results. Pictures show an OXA on a Lot 5 lathe.? Also a picture of my Lot 2 serial number 36.?
Hello, I just came across a lot 2 Dalton lathe and want to add a tool post to this. I am looking for some feedback on what others have done. I’m also interested in a 4” Chuck for this.? Does anyone have parts for these lathes?
I’m glad I found this group so I can ask more questions pertaining to these vintage, unique lathes.
Craig
|
Thanks for the input I’m going to get one of those tool posts
toggle quoted message
Show quoted text
On Nov 21, 2023, at 11:00?AM, Dennis Turk <dennisturk448@...> wrote:
? Also note there is a spacer under the tool post on the Lot 5. You should not need this on your Lot 2. Lot 2 lathes were built in 1913 and are six inch swing lathes where later lathes in this series were 7 1/4 swing.? As to parts I have a few Lot 2 parts left from two parts lathes I have.. As to a tool post the OXA size quick change tool post is your best bet.? I have used this size tool post on my Lot 5 as well as my Dalton Lot 6 lathe with great results. Pictures show an OXA on a Lot 5 lathe.? Also a picture of my Lot 2 serial number 36.?
Hello, I just came across a lot 2 Dalton lathe and want to add a tool post to this. I am looking for some feedback on what others have done. I’m also interested in a 4” Chuck for this.? Does anyone have parts for these lathes?
I’m glad I found this group so I can ask more questions pertaining to these vintage, unique lathes.
Craig
|
Also note there is a spacer under the tool post on the Lot 5. You should not need this on your Lot 2.
Lot 2 lathes were built in 1913 and are six inch swing lathes where later lathes in this series were 7 1/4 swing.? As to parts I have a few Lot 2 parts left from two parts lathes I have.. As to a tool post the OXA size quick change tool post is your best bet.? I have used this size tool post on my Lot 5 as well as my Dalton Lot 6 lathe with great results. Pictures show an OXA on a Lot 5 lathe.? Also a picture of my Lot 2 serial number 36.?
Hello, I just came across a lot 2 Dalton lathe and want to add a tool post to this. I am looking for some feedback on what others have done. I’m also interested in a 4” Chuck for this.? Does anyone have parts for these lathes?
I’m glad I found this group so I can ask more questions pertaining to these vintage, unique lathes.
Craig
|
Lot 2 lathes were built in 1913 and are six inch swing lathes where later lathes in this series were 7 1/4 swing.? As to parts I have a few Lot 2 parts left from two parts lathes I have.. As to a tool post the OXA size quick change tool post is your best bet.? I have used this size tool post on my Lot 5 as well as my Dalton Lot 6 lathe with great results. Pictures show an OXA on a Lot 5 lathe.? Also a picture of my Lot 2 serial number 36.?
Hello, I just came across a lot 2 Dalton lathe and want to add a tool post to this. I am looking for some feedback on what others have done. I’m also interested in a 4” Chuck for this.? Does anyone have parts for these lathes?
I’m glad I found this group so I can ask more questions pertaining to these vintage, unique lathes.
Craig
|
This is what I use
https://www.amazon.com/JWGJW-Tooling-Package-Holders-Multifid/dp/B018QMTXB0/ref=asc_df_B018QMTXB0/?tag=hyprod-20&linkCode=df0&hvadid=216468866073&hvpos=&hvnetw=g&hvrand=6283432264039505114&hvpone=&hvptwo=&hvqmt=&hvdev=m&hvdvcmdl=&hvlocint=&hvlocphy=9003348&hvtargid=pla-351353785343&psc=1&mcid=f5c778b094dc35868ec37cd1ecbd8584&gclid=CjwKCAiAx_GqBhBQEiwAlDNAZv7C96sI2-PTuIk88VVKmPWaZaecOuzZ4L7pTwKHDdlBA6w-5BARExoCsHsQAvD_BwE
toggle quoted message
Show quoted text
Hello, I just came across a lot 2 Dalton lathe and want to add a tool post to this. I am looking for some feedback on what others have done. I’m also interested in a 4” Chuck for this.? Does anyone have parts for these lathes?
I’m glad I found this group so I can ask more questions pertaining to these vintage, unique lathes.
Craig
|
Hello, I just came across a lot 2 Dalton lathe and want to add a tool post to this. I am looking for some feedback on what others have done. I’m also interested in a 4” Chuck for this. Does anyone have parts for these lathes?
I’m glad I found this group so I can ask more questions pertaining to these vintage, unique lathes.
Craig
|
Re: Lot 4 lathe and tooling … free
All
The lathe has gone to a young man who restores motorcycles. His intent is t restore the lathe … I’ll be sending him a link to join this group.?
Thanks for all the help over the years, folks!
toggle quoted message
Show quoted text
On Nov 11, 2023, at 13:43, glenn brooks <brooks.glenn@...> wrote:
? Hi John,
Yes, still very much interested. If ?it attaches to the headstock, it will have the correct size backing plate - which is key to using it.?
Glenn?
Cell: 206.790.8711
On Nov 11, 2023, at 7:08 AM, john rosberg <john_rosberg@...> wrote:
? Glenn
Still interested in a chuck?
On Nov 11, 2023, at 01:43, Rainer Zauritz <r.zauritz@...> wrote:
? Lot 4/256
--?
Rainer?
Gesendet: Samstag, den 11.11.2023 um 05:19 Uhr
Von: "Grey Pilgrim" <pilgrim23@...>
An: [email protected]
Betreff: Re: [DaltonLathes] Lot 4 lathe and tooling … free
Serial? ?Its on the end of the Ways….
On Nov 10, 2023, at 2:34 PM, john rosberg <john_rosberg@...> wrote:
<image.png>
It’s mostly packed away so random motorcycle parts don’t fall on the poor dear.
John Rosberg
On Nov 10, 2023, at 16:23, Dennis Turk <dennisturk448@...> wrote:
?
Hi John
There are 15 change gears that go with the Dalton lathes. ?'starting with a 24 and the biggest is a 96. ?Let's see how good my memory is. ?24 30 32 36 40 44 46 48 52 54 56 60 66 72 96. ?Should be two 24 so I may have one listerd
that is not correct. ?Ha not bad for an old 82 year old. ?Pictures are always nice to see John.
Dennis
On Fri, Nov 10, 2023 at 12:48?PM john rosberg <john_rosberg@... <mailto:john_rosberg@...>> wrote:
Lot 4, no. 256. Two three jaw chucks, a lantern tool holder and what is likely a shop made tool holder (by the previous owner). I believe all the change gears are here, as well and a collet closer (twist to close).
The lathe was given to me, so I’m passing it along the same way.
Pickup from the northern Chicago suburbs.
John Rosberg
|
Re: Lot 4 lathe and tooling … free
Drop me a line to my email … we’ll work it out!
toggle quoted message
Show quoted text
On Nov 11, 2023, at 13:43, glenn brooks <brooks.glenn@...> wrote:
? Hi John,
Yes, still very much interested. If ?it attaches to the headstock, it will have the correct size backing plate - which is key to using it.?
Glenn?
Cell: 206.790.8711
On Nov 11, 2023, at 7:08 AM, john rosberg <john_rosberg@...> wrote:
? Glenn
Still interested in a chuck?
On Nov 11, 2023, at 01:43, Rainer Zauritz <r.zauritz@...> wrote:
? Lot 4/256
--?
Rainer?
Gesendet: Samstag, den 11.11.2023 um 05:19 Uhr
Von: "Grey Pilgrim" <pilgrim23@...>
An: [email protected]
Betreff: Re: [DaltonLathes] Lot 4 lathe and tooling … free
Serial? ?Its on the end of the Ways….
On Nov 10, 2023, at 2:34 PM, john rosberg <john_rosberg@...> wrote:
<image.png>
It’s mostly packed away so random motorcycle parts don’t fall on the poor dear.
John Rosberg
On Nov 10, 2023, at 16:23, Dennis Turk <dennisturk448@...> wrote:
?
Hi John
There are 15 change gears that go with the Dalton lathes. ?'starting with a 24 and the biggest is a 96. ?Let's see how good my memory is. ?24 30 32 36 40 44 46 48 52 54 56 60 66 72 96. ?Should be two 24 so I may have one listerd
that is not correct. ?Ha not bad for an old 82 year old. ?Pictures are always nice to see John.
Dennis
On Fri, Nov 10, 2023 at 12:48?PM john rosberg <john_rosberg@... <mailto:john_rosberg@...>> wrote:
Lot 4, no. 256. Two three jaw chucks, a lantern tool holder and what is likely a shop made tool holder (by the previous owner). I believe all the change gears are here, as well and a collet closer (twist to close).
The lathe was given to me, so I’m passing it along the same way.
Pickup from the northern Chicago suburbs.
John Rosberg
|
Re: Lot 4 lathe and tooling … free
Hi John,
Yes, still very much interested. If ?it attaches to the headstock, it will have the correct size backing plate - which is key to using it.?
Glenn?
toggle quoted message
Show quoted text
On Nov 11, 2023, at 7:08 AM, john rosberg <john_rosberg@...> wrote:
?
Glenn
Still interested in a chuck?
On Nov 11, 2023, at 01:43, Rainer Zauritz <r.zauritz@...> wrote:
? Lot 4/256
--?
Rainer?
Gesendet: Samstag, den 11.11.2023 um 05:19 Uhr
Von: "Grey Pilgrim" <pilgrim23@...>
An: [email protected]
Betreff: Re: [DaltonLathes] Lot 4 lathe and tooling … free
Serial? ?Its on the end of the Ways….
On Nov 10, 2023, at 2:34 PM, john rosberg <john_rosberg@...> wrote:
<image.png>
It’s mostly packed away so random motorcycle parts don’t fall on the poor dear.
John Rosberg
On Nov 10, 2023, at 16:23, Dennis Turk <dennisturk448@...> wrote:
?
Hi John
There are 15 change gears that go with the Dalton lathes. ?'starting with a 24 and the biggest is a 96. ?Let's see how good my memory is. ?24 30 32 36 40 44 46 48 52 54 56 60 66 72 96. ?Should be two 24 so I may have one listerd
that is not correct. ?Ha not bad for an old 82 year old. ?Pictures are always nice to see John.
Dennis
On Fri, Nov 10, 2023 at 12:48?PM john rosberg <john_rosberg@... <mailto:john_rosberg@...>> wrote:
Lot 4, no. 256. Two three jaw chucks, a lantern tool holder and what is likely a shop made tool holder (by the previous owner). I believe all the change gears are here, as well and a collet closer (twist to close).
The lathe was given to me, so I’m passing it along the same way.
Pickup from the northern Chicago suburbs.
John Rosberg
|
Re: Lot 4 lathe and tooling … free
Glenn
Still interested in a chuck?
toggle quoted message
Show quoted text
On Nov 11, 2023, at 01:43, Rainer Zauritz <r.zauritz@...> wrote:
? Lot 4/256
--?
Rainer?
Gesendet: Samstag, den 11.11.2023 um 05:19 Uhr
Von: "Grey Pilgrim" <pilgrim23@...>
An: [email protected]
Betreff: Re: [DaltonLathes] Lot 4 lathe and tooling … free
Serial? ?Its on the end of the Ways….
On Nov 10, 2023, at 2:34 PM, john rosberg <john_rosberg@...> wrote:
<image.png>
It’s mostly packed away so random motorcycle parts don’t fall on the poor dear.
John Rosberg
On Nov 10, 2023, at 16:23, Dennis Turk <dennisturk448@...> wrote:
?
Hi John
There are 15 change gears that go with the Dalton lathes. ?'starting with a 24 and the biggest is a 96. ?Let's see how good my memory is. ?24 30 32 36 40 44 46 48 52 54 56 60 66 72 96. ?Should be two 24 so I may have one listerd
that is not correct. ?Ha not bad for an old 82 year old. ?Pictures are always nice to see John.
Dennis
On Fri, Nov 10, 2023 at 12:48?PM john rosberg <john_rosberg@... <mailto:john_rosberg@...>> wrote:
Lot 4, no. 256. Two three jaw chucks, a lantern tool holder and what is likely a shop made tool holder (by the previous owner). I believe all the change gears are here, as well and a collet closer (twist to close).
The lathe was given to me, so I’m passing it along the same way.
Pickup from the northern Chicago suburbs.
John Rosberg
|
Re: Lot 4 lathe and tooling … free
Lot 4/256
--?
Rainer
toggle quoted message
Show quoted text
Gesendet: Samstag, den 11.11.2023 um 05:19 Uhr
Von: "Grey Pilgrim" <pilgrim23@...>
An: [email protected]
Betreff: Re: [DaltonLathes] Lot 4 lathe and tooling … free
Serial? Its on the end of the Ways….
On Nov 10, 2023, at 2:34 PM, john rosberg <john_rosberg@...> wrote:
<image.png>
It’s mostly packed away so random motorcycle parts don’t fall on the poor dear.
John Rosberg
On Nov 10, 2023, at 16:23, Dennis Turk <dennisturk448@...> wrote:
?
Hi John
There are 15 change gears that go with the Dalton lathes. 'starting with a 24 and the biggest is a 96. Let's see how good my memory is. 24 30 32 36 40 44 46 48 52 54 56 60 66 72 96. Should be two 24 so I may have one listerd that is not correct. Ha not bad for an old 82 year old. Pictures are always nice to see John.
Dennis
On Fri, Nov 10, 2023 at 12:48?PM john rosberg <john_rosberg@... <mailto:john_rosberg@...>> wrote:
Lot 4, no. 256. Two three jaw chucks, a lantern tool holder and what is likely a shop made tool holder (by the previous owner). I believe all the change gears are here, as well and a collet closer (twist to close).
The lathe was given to me, so I’m passing it along the same way.
Pickup from the northern Chicago suburbs.
John Rosberg
|
Re: Lot 4 lathe and tooling … free
Serial? ?Its on the end of the Ways….
toggle quoted message
Show quoted text
<image.png>
It’s mostly packed away so random motorcycle parts don’t fall on the poor dear.
?
Hi John
There are 15 change gears that go with the Dalton lathes.? 'starting with?a 24 and the biggest is a 96.? Let's see how good my memory?is.? 24 30 32 36 40 44 46 48 52 54 56 60 66 72 96.? Should be two 24 so I may have one listerd that is not correct.? Ha
not bad for an old 82 year old.? Pictures are always nice to see John.?
Dennis
Lot 4, no. 256. Two three jaw chucks, a lantern tool holder and what is likely a shop made tool holder (by the previous owner). I believe all the change gears are here, as well and a collet closer (twist to close).
The lathe was given to me, so I’m passing it along the same way.
Pickup from the northern Chicago suburbs.
|
Re: Lot 4 lathe and tooling … free
Hey Dennis. Hope all is well my mentor…. ?Btw…did I ever tell you: ?thanks? ? THANK YOU SIR. ?You taught me, and my son…. ?I am only 70 but doing well..
toggle quoted message
Show quoted text
Hi John There are 15 change gears that go with the Dalton lathes.? 'starting with?a 24 and the biggest is a 96.? Let's see how good my memory?is.? 24 30 32 36 40 44 46 48 52 54 56 60 66 72 96.? Should be two 24 so I may have one listerd that is not correct.? Ha not bad for an old 82 year old.? Pictures are always nice to see John.? Dennis
Lot 4, no. 256. Two three jaw chucks, a lantern tool holder and what is likely a shop made tool holder (by the previous owner). I believe all the change gears are here, as well and a collet closer (twist to close).
The lathe was given to me, so I’m passing it along the same way.
Pickup from the northern Chicago suburbs.
|
Re: Lot 4 lathe and tooling … free
I am also in the Chicago area suburbs and will be happy to take it. My own Dalton 6 has some broken components and I love the idea of using another Dalton to make the parts to fix it. Then I can pass mine on to another home.
John
Lot 4, no. 256. Two three jaw chucks, a lantern tool holder and what is likely a shop made tool holder (by the previous owner). I believe all the change gears are here, as well and a collet closer (twist to close).
The lathe was given to me, so I’m passing it along the same way.
Pickup from the northern Chicago suburbs.
|
Re: Lot 4 lathe and tooling … free
It’s mostly packed away so random motorcycle parts don’t fall on the poor dear.
toggle quoted message
Show quoted text
On Nov 10, 2023, at 16:23, Dennis Turk <dennisturk448@...> wrote:
?
Hi John
There are 15 change gears that go with the Dalton lathes.? 'starting with?a 24 and the biggest is a 96.? Let's see how good my memory?is.? 24 30 32 36 40 44 46 48 52 54 56 60 66 72 96.? Should be two 24 so I may have one listerd that is not correct.? Ha
not bad for an old 82 year old.? Pictures are always nice to see John.?
Dennis
Lot 4, no. 256. Two three jaw chucks, a lantern tool holder and what is likely a shop made tool holder (by the previous owner). I believe all the change gears are here, as well and a collet closer (twist to close).
The lathe was given to me, so I’m passing it along the same way.
Pickup from the northern Chicago suburbs.
|
Re: Lot 4 lathe and tooling … free
Hi,
I'm in La Grange.? I'd love to pick up your lathe. I'm in Cleveland
until Sunday.
Thanks, Ralph?? 708-280-2560
john rosberg wrote:
Lot 4, no. 256. Two three jaw chucks, a lantern tool holder and
what is likely a shop made tool holder (by the previous owner). I
believe all the change gears are here, as well and a collet closer
(twist to close).
The lathe was given to me, so I’m passing it along the same
way.
Pickup from the northern Chicago suburbs.
--
PLEASE BE KIND TO YOUR EMAIL FRIENDS
Before forwarding please remove all email addresses and use the
BCC option to add your contacts. Failure to do so results in spam
and email from people you don't know.
THANK YOU
|
Re: Lot 4 lathe and tooling … free
John, I’m in the western Chicago suburbs. ?I have a 9 inch. ?Any pictures of the lathe?
toggle quoted message
Show quoted text
On Nov 10, 2023, at 4:23 PM, Dennis Turk <dennisturk448@...> wrote:
? Hi John There are 15 change gears that go with the Dalton lathes.? 'starting with?a 24 and the biggest is a 96.? Let's see how good my memory?is.? 24 30 32 36 40 44 46 48 52 54 56 60 66 72 96.? Should be two 24 so I may have one listerd that is not correct.? Ha not bad for an old 82 year old.? Pictures are always nice to see John.? Dennis
Lot 4, no. 256. Two three jaw chucks, a lantern tool holder and what is likely a shop made tool holder (by the previous owner). I believe all the change gears are here, as well and a collet closer (twist to close).
The lathe was given to me, so I’m passing it along the same way.
Pickup from the northern Chicago suburbs.
|
Re: Lot 4 lathe and tooling … free
Hi John There are 15 change gears that go with the Dalton lathes.? 'starting with?a 24 and the biggest is a 96.? Let's see how good my memory?is.? 24 30 32 36 40 44 46 48 52 54 56 60 66 72 96.? Should be two 24 so I may have one listerd that is not correct.? Ha not bad for an old 82 year old.? Pictures are always nice to see John.? Dennis
Lot 4, no. 256. Two three jaw chucks, a lantern tool holder and what is likely a shop made tool holder (by the previous owner). I believe all the change gears are here, as well and a collet closer (twist to close).
The lathe was given to me, so I’m passing it along the same way.
Pickup from the northern Chicago suburbs.
|
Re: Lot 4 lathe and tooling … free
Glenn?
Neither chuck has a dalton logo or brand on it … one has this stamped on the face
toggle quoted message
Show quoted text
On Nov 10, 2023, at 15:34, glenn brooks <brooks.glenn@...> wrote:
? John,?
Could I buy one of your 3 jaw chucks, with backplate?
Please, please??
My chuck is original and completely worn( bell mouth jaws) ?out from 102 years use…?
All the dalton chucks were apparently individually matched to each back plate. ?
Iam in Seattle area. Happy to pay for shipping also
Thanks much
Glenn Brooks
Cell: 260-790-8711
On Nov 10, 2023, at 12:48?PM, john rosberg <john_rosberg@...> wrote:
? Lot 4, no. 256. Two three jaw chucks, a lantern tool holder and what is likely a shop made tool holder (by the previous owner). I believe all the change gears are here, as well and a collet closer (twist to close).
The lathe was given to me, so I’m passing it along the same way.
Pickup from the northern Chicago suburbs.
|
Re: Lot 4 lathe and tooling … free
John,?
Could I buy one of your 3 jaw chucks, with backplate?
Please, please??
My chuck is original and completely worn( bell mouth jaws) ?out from 102 years use…?
All the dalton chucks were apparently individually matched to each back plate. ?
Iam in Seattle area. Happy to pay for shipping also
Thanks much Glenn Brooks Cell: 260-790-8711
toggle quoted message
Show quoted text
On Nov 10, 2023, at 12:48?PM, john rosberg <john_rosberg@...> wrote:
?
Lot 4, no. 256. Two three jaw chucks, a lantern tool holder and what is likely a shop made tool holder (by the previous owner). I believe all the change gears are here, as well and a collet closer (twist to close).
The lathe was given to me, so I’m passing it along the same way.
Pickup from the northern Chicago suburbs.
|
Dennis Turk
glenn brooks
John