开云体育

+ AA6YQ comments below I'm having an issue with Commander controling my two radios. I'm running a Ten-Tec Orion 2 and a Kenwood TS-890. Whenever I select the radio button to move from the Orion 2 to

From the log page display, right click on the QSO and choose Update from LoTW. Does that change the status? 73, Mike ND9G [email protected]> wrote:

Rod - I think I am near the end of my short list of ideas... but here are two more things to look at: 1: Make sure the dates under the LoTW sync buttons are the dates on which you invoked those sync

Yes, I did both sync processes as well as I did one manually by right clicking on it.

Rod - You say you have completed the sync process... but did you sync both LoTW QSOs AND LoTW QSLs? If you only synced LoTW QSOs I believe you would see the results you have. GL de Dave - K9FN

Need a little help regarding LoTW and DXKeeper Codes - I worked VP8PJ three times, once on each of SSB, CW, and FT8. I logged the Qs and submitted them to LoTW via Keeper. I have recently looked them

FT4 is a sub-mode for MFSK -- L'absence de virus dans ce courrier électronique a été vérifiée par le logiciel antivirus Avast. https://www.avast.com/antivirus

I worked DS5USH last night on FT4 and he has confirmed on LoTW. LotW QSL says mode FT4 and my log says FT4 and all matched up. But the LotW status report says MFSK. Date Time Call Band Mode Station

I'm having an issue with Commander controling my two radios. I'm running a Ten-Tec Orion 2 and a Kenwood TS-890. Whenever I select the radio button to move from the Orion 2 to the TS-890, after a few

Other than an occasional scan by Malwarebytes Free I also only use W10 Security/Defender and have since system was new. Have run DXLab suite also since system was purchased. Never have gotten any

Yep - I ran a scan with latest Malwarebytes Free and it found nothing.

FWIW ... Microsoft is getting very aggressive at ham radio programs.????? The latest setup program for JTALert v2.16.0 gave a false positive by MS Security Essentials.???? One person sent in

My main shack machine had the W10 upgrade finished a few hours ago.?? Ran commander? no warnings and works fine.?? Protection by Microsoft only.?? Quarantined is a term used by Mcaffee for sure

+ AA6YQ comments below Suddenly today when trying to start the most recent Commander it is being quarantined by W10 Security as having a Trojan Specifically W32/Azden.Blcl Anyone seeing same? It

Suddenly today when trying to start the?most recent Commander it is being quarantined by W10 Security as having a Trojan? ?Specifically W32/Azden.Blcl Anyone seeing same?? ? It appears there was

Dave - In safe mode the behavior was what I expected. I rebooted (out of safe mode) and tried again... now it is again behaving normally. I do wonder if I have failed to correctly configure MS

This afternoon I am seeing something that I don't believe was happening in the past. About 90 minutes ago I worked VP2VB before taking a break for lunch. When I came back to the rig the "arrow" at the

This afternoon I am seeing something that I don't believe was happening in the past. About 90 minutes ago I worked VP2VB before taking a break for lunch. When I came back to the rig the "arrow" at the

+ AA6YQ comments below Hi Dave, the problem has been rectified thank you. I did upgrade to 15.4.6. I disabled all award tracking, then re-enabled which rebuilt the databases, I guess. + Disabling

Hi Dave, the problem has been rectified thank you.? I did upgrade to 15.4.6.? I disabled all award tracking, then re-enabled which rebuilt the databases, I guess.? Also re-booted, and now it seems