开云体育

The primary purpose of this release is to correct the defect in Hygain DCU rotator support reported by Julio below. I learned from Ed at DataMatrix (the developers of ProLog) that the "set bearing"

I import more than 1000 qso's from logger with out problems -----Oorspronkelijk bericht----- Verzonden: woensdag 21 maart 2001 23:50 Aan: dxlab@... Onderwerp: RE: [dxlab] Re: Progress

Our man Kurt, OE1002419, noticed that both the FR and LZ callbook URLs had changed, tracked down the new URLs, and sent them my way. So we have him to thank for the updated Pathfinder searches now

Sounds like there's a latent defect in the DDE connection between DXKeeper and DXLab. I suggest you hold off until I release a version of of DXKeeper that performs the country code lookup without

I don't know, but I am having a great deal of difficulty with the import. I took out all the DXCC entries in the ADIF file to force a lookup in DXView. It starts off going OK, pretty slow but I

Yes, if there's a country code present in the imported QSO, DXKeeper respects it. The procedure you suggest will result in each imported callsign being checked by DXView to determine a country

I'm not sure if DXView was open when I did the import. However, it was open when I did the recompute. I just did that again to make sure, it didn't help. However, I just noticed something else. When I

Without seeing your log, I can't know for sure, but my suspicion is that many of your DXKeeper log entries are missing DXCC country codess -- likely because DXView was not running when these entries

Dave, When I click on a callsign in DXKeeper, obviously I have worked the guy, but the progress window does not always indicate any contact with his country. Also, I have worked 3G0Y 8 times

I've added additional error trapping to this version -- hopefully the runtime error 6 crash W3ZJ's been experiencing will be replaced by an entry in the error log that helps me track down the root

Rich found the documentation on their web site. Given that its a DDE interface, I'll need a copy of their software for testing. It'd be best to get the software directly from the supplier -- as a

Correct And his suport are great. -----Oorspronkelijk bericht----- Verzonden: dinsdag 20 maart 2001 23:54 Aan: Dxlab Onderwerp: [dxlab] ARS rotor control Dave, Take a look at the following

Dave, Take a look at the following link http://www.ea4tx.com/index_en.htm which is some developers information on the rotor control that Ron asked about. From what I can gather it is not an RS232

it's use the paralel port as the printer. I can send you the program -----Oorspronkelijk bericht----- Verzonden: dinsdag 20 maart 2001 22:12 Aan: dxlab@... Onderwerp: [dxlab] Re:

If there's documentation for the RS232 command set, then yes its possible. I checked the web site but didn't see this documentation. If you have it, please forward me a copy. 73, Dave,

I'll construct a version of CI-V Commander that notes such errors in the error log rather than terminating execution. The error log information should help me track down the root cause. 73,

Yep thats good Is't posible to use the modem and software for EA4TX rotor control? see http://www,ea4tx.com this is not a comurcial bud i run this and like it. Ron PA1ZX -----Oorspronkelijk

Dave, I have been trying the new capture window and like it very much. This morning, I got the run time error from CI-V commander without WinWarbler running. What I had open was CI-V commander,

Ron, Your test got through, and welcome to the group. The reflector is just getting started so we are a very small group right now, you are a charter member. As such, you probably won't be getting

Ron PA1ZX DXForecast http://members1.chello.nl/~r.a.f.eberson/DXF