开云体育

In the Admin Menu, select item 9 - Start Bash Shell Interface Enter the command - lsusb You will get a list of USB devices attached to your Pi. Look for the C-Media device. The VID and PID (Vendor ID

How can I tell what chip is built into my DINA, CM119B or CM108B USB audio codec integrated circuit? It appears to make a difference in how audio is adjusted for use in the allstars application. NOTES

I am sorry for not being more specific. The audio from my allstar node RPi3b+ to the Kenwood TMv71a is the audio that i am having problems with. The audio from the radio though the node sounds

Oops - I have used DINAH with the TM-V7A, not the TM-V71A.

JP1 was included in case someone wanted to use DINAH for a non-standard interface to a radio.The center pad of JP1 (JP1-2) is connected to Pin 4 of the miniDIN connector (which is 9600 in the packet

I finally got my DINAH running into a Kenwood TMV71A as an all star node and it sounds like crap. I set up the TMV71A menu 518 and 519 to the appropriate settings. I adjusted everything i could on the

Thank you.? I was pretty sure that was going to be the answer.? I will look into your suggestions.? I still have much to learn about how all this stuff works. LarryKJ7OEZ On Wed, Aug 5, 2020 at

I am not aware of an HT with a packet data connector.? However, our BRIAN kit essentially consists of the circuit board from a Baofeng BF888s HT and the same circuitry as DINAH.? Also our SHARI kit

I recently purchased a Dinah module and it is now connected to my mobile unit.? It was such an easy setup that I now would like to create a portable node for the local club.? But it needs to be on a

KE5SQC, Randy here. I am using the FT-7900R with my DINAH and it works PERFECT!? No Issues.#52070

I was having trouble with my DINAH startup at the USB config stage. My two available DIN cables (I'd lost track of which came with the kit) were 8-pin so I had to remove the "center" pin on both ends.

I have not connected a DINAH to an FT 7900R? but checking the manual, I see that it has the standard packet interface using the 6 pin miniDIN connector so it should wok fine. Steve - N8AR

Has anyone successfully connected DINAH to a Yaesu FT7900R? -- Ken - *NN3F*

I have no personal experience with HAMLIB but I believe your problem is you are missing a cable.? HamVOIP Allstar includes the HAMLIB but the connection for sending HAMLIB control commands to your

I purchased the DINAH as a means to connect my V71a to an allstar node (RPI3b+) and control it (frequency agile) using the HAMLIB rigctl library. To test i am using the command " rigctl -m 227 -r

Hello, This email message is a notification to let you know that the following files have been uploaded to the Files area of the [email protected] group. * /Alinco DE-X35 DE-9 Connector Wiring to

Hi Chuck, Thank you for the feedback.? I hope your 857D is an easy repair, I have added the Icom IC-7100 to the list of radios compatible with DINAH.. Steve - N8AR

Hi Steve, Just wanted to let you know that my FT-857D 6-pin DIN connector is partially dead.? That is the reason Dinah does not seem to work.? I connected my Kantronics KPC3+ to try to connect to

Hello, This email message is a notification to let you know that the following files have been uploaded to the Files area of the [email protected] group. * /Some Radios with the 6 Pin miniDIN interface

Hi Chuck, I hooked my FT-857D up to SHARI again to test with the production version of DINAH since my previous testing was with various prototypes,? As you noted, the overmold precludes the miniDIN