You don't RX anything on FT7800 when you Tx your Handheld? Did you enable tones on FT7800. Your FT7800 should Rx a signal from your handy and pass it through DINAH and made your Node TX.
Hello DINAH users.
I have just purchased a DINAH - C (USBC) model.
I am trying to setup the DINAH with my Raspberry Pi4B.
It is receiving and the radio is then transmitting from a node that it's connected to, so I can hear stations via my Handy from the FT7800, but When I transmit using my Handy on the same frequency nothing looks to be happening.
It is not keying up the DINAH ?
Any help or if someone has a working Image file for the Raspberry PI tuning the DINAH for the FT7800 radio, it would be appreciated !
Cheers and thanks
Craig.
VK3NCR
?
|
2nd thought, is there a packet menu that needs to be set to enable the IO on the the 6 pin mini din? I believe it needs to be set to 1200. Steve VK2ARS
toggle quoted message
Show quoted text
-------- Original message -------- From: Craig <vk3ncrmail@...> Date: 16/2/24 14:11 (GMT+10:00) Subject: [DINAH] Yaesu FT7800 / 7900
Hello DINAH users. I have just purchased a DINAH - C (USBC) model. I am trying to setup the DINAH with my Raspberry Pi4B. It is receiving and the radio is then transmitting from a node that it's connected to, so I can hear stations via my Handy from the FT7800, but When I transmit using my Handy on the same frequency nothing looks to be happening. It is not keying up the DINAH ? Any help or if someone has a working Image file for the Raspberry PI tuning the DINAH for the FT7800 radio, it would be appreciated ! Cheers and thanks Craig. VK3NCR ?
|
Hi Craig, not a CTCSS mis-match between the HT and the 7800?
First thing that came to mind. Steve VK2ARS
toggle quoted message
Show quoted text
-------- Original message -------- From: Craig <vk3ncrmail@...> Date: 16/2/24 14:11 (GMT+10:00) Subject: [DINAH] Yaesu FT7800 / 7900
Hello DINAH users. I have just purchased a DINAH - C (USBC) model. I am trying to setup the DINAH with my Raspberry Pi4B. It is receiving and the radio is then transmitting from a node that it's connected to, so I can hear stations via my Handy from the FT7800, but When I transmit using my Handy on the same frequency nothing looks to be happening. It is not keying up the DINAH ? Any help or if someone has a working Image file for the Raspberry PI tuning the DINAH for the FT7800 radio, it would be appreciated ! Cheers and thanks Craig. VK3NCR ?
|
If you call Dinah they will help you with your specific radio. If anything else I'll try to help.
Hello DINAH users.
I have just purchased a DINAH - C (USBC) model.
I am trying to setup the DINAH with my Raspberry Pi4B.
It is receiving and the radio is then transmitting from a node that it's connected to, so I can hear stations via my Handy from the FT7800, but When I transmit using my Handy on the same frequency nothing looks to be happening.
It is not keying up the DINAH ?
Any help or if someone has a working Image file for the Raspberry PI tuning the DINAH for the FT7800 radio, it would be appreciated !
Cheers and thanks
Craig.
VK3NCR
?
|
Be sure that the miniDIN connector is fully seated into the jack on the FT8800.? I think I had to shave off some of the overmold on the connector on the cable when I set up my DINAH/FT-8800 node.
?
Here is the simpleusb settings I use.
?
Be sure Item L) is set to none
?
Be sure you have the setting correct in the FT-8800 menu for 1200 baud.? Here is an excerpt from the Yaesu manual.
?
|
Hello DINAH users.
I have just purchased a DINAH - C (USBC) model.
I am trying to setup the DINAH with my Raspberry Pi4B.
It is receiving and the radio is then transmitting from a node that it's connected to, so I can hear stations via my Handy from the FT7800, but When I transmit using my Handy on the same frequency nothing looks to be happening.
It is not keying up the DINAH ?
Any help or if someone has a working Image file for the Raspberry PI tuning the DINAH for the FT7800 radio, it would be appreciated !
Cheers and thanks
Craig.
VK3NCR
?
|
HI,
May I join in.. Just received my DINAH-C and like this chap, I am receiving from Nodes.. But I have no audio going to out..?
Option 2.. RX VOICE DISPLAY
I have nothing being displayed.
Hope you can help me and this chap too.. Sorry to jump in.
Craig
vk3ncr
|
HI,
May I join in.. Just received my DINAH-C and like this chap, I am receiving from Nodes.. But I have no audio going to out..?
Option 2.. RX VOICE DISPLAY
I have nothing being displayed.
Hope you can help me and this chap too.. Sorry to jump in.
Craig
vk3ncr
|
Hello, I am new to this DIINAH thing.? However, I am familiar with Linux.? I have an intel laptop running all the allstar stuff, connected the DINAH to an FT991.? Have the FT991 set up as -RPTR, with CTC tone.? I have a permanent reconnecting link for allstar to connect to East Coast Reflector.? Now all is going well, and we can receive traffic from ECR just fine.? Keying up a handy, I see the FT991 TX trigger, but using echolink to check, I am not getting tx indications nor audio when transmitting from a handy to the FT991.? So maybe allstar setting for the DINAH is not registering an incoming local transmit?
Any help is greatly appreciated.
|
I need to be able to use a thumbdv USB , that had no USB connection for that. I need a modified sound fob I can't seem to find such on eBay or anywhere. I have your shari I have tested everything just a bad hum/buzz I can't get rid of? I have a Pi4 and I am putting together a all-star dvswitch setup will a added thumbdv w/ambe chip. I want to use like a bf888.. do you know where I can find a already modified USB sound-fob. I am no good at soldering. That's all I really need. Any help I'll take
On Thu, Nov 2, 2023, 8:53 AM N8AR < n8ar73@...> wrote: Probably not.? The COS and PTT interface is the same but BRIAN has 10K series resistors in the audio connections which are not in DINAH.? Assuming you connect to the same points in the BF888S that are used in BRIAN, you could add them where you make the connections to the BF888S.? But why not just use our a BRIAN.
|
Probably not.? The COS and PTT interface is the same but BRIAN has 10K series resistors in the audio connections which are not in DINAH.? Assuming you connect to the same points in the BF888S that are used in BRIAN, you could add them where you make the connections to the BF888S.? But why not just use our a BRIAN.
|
this should work with a BF888 baofang for use with allstar , correct ??
thanks
n8dad
|
Re: Dinah not turning on.
My Raspberry went dead. Just ordered a New one.?
The Dinah will not turn on with the pi but it will on any other?device, My computer my hot spot but not on the pi, so looks like my pi is dead!
On Fri, Jun 23, 2023, 4:35 PM N8AR < n8ar73@...> wrote: Unplug the DINAH and try again.? If it does not boot then you have a problem with the Pi, the image on the uSD card or your Pi Power supply.
Do any LED's on the Pi light up?
|
Re: Dinah not turning on.
The Dinah will not turn on with the pi but it will on any other?device, My computer my hot spot but not on the pi, so looks like my pi is dead!
On Fri, Jun 23, 2023, 4:35 PM N8AR < n8ar73@...> wrote: Unplug the DINAH and try again.? If it does not boot then you have a problem with the Pi, the image on the uSD card or your Pi Power supply.
Do any LED's on the Pi light up?
|
Re: Dinah not turning on.
By the way how much are your pi's??
On Fri, Jun 23, 2023, 4:35 PM N8AR < n8ar73@...> wrote: Unplug the DINAH and try again.? If it does not boot then you have a problem with the Pi, the image on the uSD card or your Pi Power supply.
Do any LED's on the Pi light up?
|
Re: Stumped: Can't use Dinah with 9600 Baud Pin/Kenwood Radio
FWIW:
Because you are only changing the output pin of the radio through
a crossover cable, you shouldn't actually change the radio to 9600
in menu 518, as both output pins are always active. Changing to
9600 only affects the single input pin on the radio, which should
be left at 1200 for optimal use.
I don't have one of these adapters, but I do have a cable with
the same pins 4 and 5 crossed over, and this isn't necessary.
I had a cable made to do this specifically so I didn't have to
modify the DINAH itself.
On 7/4/2023 4:58 PM, N8AR wrote:
toggle quoted message
Show quoted text
Did you verify the cable wiring with an ohmmeter?
Did you set the speed to 9600 in the TM-V71's menu 518?
Also, you do not need a special cable for DINAH to use 9600.? Just
cut the trace between JP1 and JP2.? Short JP3 to JP2 with a solder
bridge.
|
Re: Stumped: Can't use Dinah with 9600 Baud Pin/Kenwood Radio
Did you verify the cable wiring with an ohmmeter?
Did you set the speed to 9600 in the TM-V71's menu 518?
Also, you do not need a special cable for DINAH to use 9600.? Just cut the trace between JP1 and JP2.? Short JP3 to JP2 with a solder bridge.
|
Stumped: Can't use Dinah with 9600 Baud Pin/Kenwood Radio
Hi. ? I have a Dinah and a Kenwood TM-V71A. ? I have a couple friends with the same set up who have switched DIN plug pins 4 and 5, and are getting flatter/nicer audio as a result. We all ordered the same adapter cable from Mobilink to do this. ? Two of us are hearing ourselves on Allstar when we transmit into the node radio with an HT. I am not. I have copied all settings: packet sensitivity, SQC, etc. to copy my friend’s, and still nothing. ? I have two TM-V71’s, so I did a full reset on the second one, and copied my friend’s settings for the data port and still, no audio. That rules out a possible problem with one radio’s data port. NOTE: If I crank SimpleUSB menu 2, RX level, all the way up, and turn on RX boost, I can hear myself but very quietly. ? Audio coming the other way, from Allstar is fine. ? What could be the problem? There aren’t many things to adjust here, so I am stumped. ? All suggestions welcome. ? Thanks and 73 ? Chris ?
|
Re: Kenwood TM-V7 and CTCSS
Made a bit of a mistake here:
I meant to say SQL when I said CSQ.
The default on the TM-V71A/E for COS is BUSY, which is
essentially just carrier. It can be changed on this radio to SQL,
which is more appropriate, but not on the older Kenwood radios, at
least without mods.
On 7/2/2023 7:19 AM, Patrick Perdue
wrote:
toggle quoted message
Show quoted text
Greetings:
The older Kenwoods have COS logic hard-wired to carrier. With
radios like the TM-V71 and TM-G710, you can change this in a
menu to CSQ. On the TM-V71A/E, this is done in menu 5-2-0.
I have the same problem with an older TM-D700A. There is
probably a hardware mod for this, but I don't know.
On 7/1/2023 10:27 PM, N9MS Mike
Saeger wrote:
I decided to turn on CTCSS on my Allstar/Kenwood TM-V7. I
thought I would be able to open up the squelch but it apparently
turns on COS when the squelch is open but no station is
transmitting?
Has anyone else run into this or is it just me? For now, I had
to adjust the squelch so COS is not triggered.
|
Re: Kenwood TM-V7 and CTCSS
Greetings:
The older Kenwoods have COS logic hard-wired to carrier. With
radios like the TM-V71 and TM-G710, you can change this in a menu
to CSQ. On the TM-V71A/E, this is done in menu 5-2-0.
I have the same problem with an older TM-D700A. There is probably
a hardware mod for this, but I don't know.
On 7/1/2023 10:27 PM, N9MS Mike Saeger
wrote:
toggle quoted message
Show quoted text
I decided to turn on CTCSS on my Allstar/Kenwood TM-V7. I thought
I would be able to open up the squelch but it apparently turns on
COS when the squelch is open but no station is transmitting?
Has anyone else run into this or is it just me? For now, I had to
adjust the squelch so COS is not triggered.
|
Mark Cruz
Steve-N8AR
KO4IYY-Steve
Chris Smart