开云体育

So far in our testing we are finding that the DINAH is compatible with any. radio which has the 6 pin mini-din "data" connector (or equivalent such as the DR0135T). In most cases we find that these

Michael, I have a Dinah that I would like to connect to my IC-9700.? How did you wire this up? Don K9AQ

Sure can, it’s just another USB audio device. -Michael Sent: Friday, April 22, 2022 7:28 PM To: [email protected] Subject: Re: [DINAH] Can Dinah run as a second radio on a Shari Pi Hat? Thanks I have

Thanks I have a Pi3b Don K9AQ

That depends on the revision of the Pi your hat is on. I have three nodes running on a single rPi 3b, a DINAH connected to a Kenwood TM-V71A, a SHARI 3U, and a TYT 220 monoband radio connected to a

I have Allstar running on a Shari Pi Hat and my plan is to implement a second node using Dinah and a Yaesu 857.? In reading the Hamvoip configuration instructions they talk about configuring a second

I have wired it to the IC-9700 and IC-7300 through the ACC jacks. Also I have some interfaced to a Yaesu DR-1X and a Motorola MTR3000 through the DB25 J7. (some connector soldering required to make

Thanks don. Sent: March 16, 2022 7:40 PM To: [email protected] Subject: Re: [DINAH] COMPREHENSIVE LIST OF COMPATIBLE RADIOS? We have tested: Yeasu FT817ND Kenwood TM-V71A ICOM IC-208 Alinco D135T MKiii

We have tested: Yeasu FT817ND Kenwood TM-V71A ICOM IC-208 Alinco D135T MKiii (DB9 with converter) ICOM IC-7000 [email protected]> wrote: -- 73, AB1PH Don Rolph

Sent from Yahoo M

Thanks Steve. Sent: March 16, 2022 2:51 PM To: [email protected] Subject: Re: [DINAH] COMPREHENSIVE LIST OF COMPATIBLE RADIOS? There is a document in the Files section of this group. It is titled "Some

There is a document in the Files section of this group. It is titled "Some Radios with the 6 pin miniDIN Interface" There probably are others.? Please let us know if you are aware of one. Also, the

Hi. My subject line says it. Is there a list somewhere of known compatible transceivers, new or used, which are known to work with the Dinah? By "work with", I mean without modifying the Dinah. To ask

DINAH is a CM119 audio interface. I think you can choose whichever module you want. -Michael Sent: Friday, February 4, 2022 4:45 PM To: [email protected] Subject: [DINAH] DINAH with App_rpt Does the

Ok so this issue was actuall simply over driven audio in the end. We re ran audio (rx) level check on hamvoip (simple usb) and brought it down to the acceptable levels and voila dtmf tones now decoded

Does the Dinah interface use chan_simpleusb or chan_usbradio please ? If the latter , does it have the DSP feature please ? Many thanks 73 de CQU

Follow the instructions in this document located in the Files section of this group to adjust your audio/DTMF levels. /g/DINAH/files/Setting the RX Level in HamVOIP Allstar.pdf

hi all, i am in need of some advise here. Recently built and installed an allstar node using a Yaesu FT -1500m as the base radio.. however when trying to use short dtmf codes/tones via my HT to manage

I am finding that the present font pof all TNC cable knowledge at thjis point is: - https://hammadeparts.com/shop-for-cables I have worked with them on a few cable issues and their cable engineering

Whoops, ignore that. I didn’t fully understand the necessary connections involved in Dinah-to-HT interfaces. Sent: February 2, 2022 9:43 AM To: [email protected] Subject: Re: [DINAH] Dinah to Kenwood