开云体育

uBITX Firmware (CEC) 0.30 released (Test version).

#ubitx

Jason Matonis All Messages By This Member #41507 On Fri, Feb 9, 2018 at 06:22 pm, Ian Lee wrote: CW Speed (5th Menu), - Currently set to 10wpm CW TX-> RX Delay (5th Extra Menu), - I've tried 0 - 200 and it is every few dits or dahs, at 600 it was after every release. CW Start Delay (6th Extra Menu) - 100? CW KeyType (7th Extra Menu) - Iambic A
Ian Lee All Messages By This Member #41509 Jason I have been using my uBITX with no modification at all.? I have not found yet a problem with the both settings.? Maybe it's a bug I could not think of. CW TX->RX Delay only sets the value so that it can be switched to RX when all CW transmissions are finished. Normally, it should be over 500. And I have found a bug that is separate from this problem. The 'CW Start Delay' was not reflected in the new CW Key logic.?so, the CW Start Delay value in version 1.01 does not affect CW key operation. This will be corrected now and will be included in version 1.02. Could you tell me more about the meaning of "extra" in your message? Ian KD8CEC 2018-02-10 12:41 GMT+09:00 Jason Matonis via Groups.Io <kb2sdrjay@...>: toggle quoted message Show quoted text On Fri, Feb 9, 2018 at 06:22 pm, Ian Lee wrote: CW Speed (5th Menu), - Currently set to 10wpm CW TX-> RX Delay (5th Extra Menu), - I've tried 0 - 200 and it is every few dits or dahs, at 600 it was after every release. CW Start Delay (6th Extra Menu) - 100? CW KeyType (7th Extra Menu) - Iambic A -- Best 73 KD8CEC / Ph.D ian lee kd8cec@... (my blog)
Jason Matonis All Messages By This Member #41517 Good morning Ian, With the CW TX->RX Delay set low 0-140 the extra dit/dah is random, with it set higher it becomes more pronounced. At the default 600, it would give an extra dit/dah after every release of the paddle. I have not made any modifications to the radio, just added the resistors inside my paddle and moved the dah wire to the dit side of the jack (internal to the paddle). I'm no CW wiz, just a guy testing out his radio to make sure everything is working.? 73 Jason KB2SDR
Ian Lee All Messages By This Member #41583 Jason. Find the problem together.??So far there has been no report on this issue. Regardless of the setting of TX-> RX Delay, it seems that wrong keys have been input. So I would like to ask you once more. Can you check the value for A6 in the ADC Monitoering menu? When the key is not pressed, When you hold down Dot, When you hold down Dash. Please let me know the above ADC results. If the values change while you hold down the key, please let us know the range. This is my second request. Please take a look at your CW Key ADC Range using uBITX Manager. This is your third request. Please let us know what happens when you upload the original firmware. I think this problem will appear the same in any CW settings.?At first I understood the 'extra' you said, but I understand now. At first I dont understood the 'extra' you said, but I understand now. Ian KD8CEC 2018-02-11 0:34 GMT+09:00 Jason Matonis via Groups.Io <kb2sdrjay@...>: toggle quoted message Show quoted text Good morning Ian, With the CW TX->RX Delay set low 0-140 the extra dit/dah is random, with it set higher it becomes more pronounced. At the default 600, it would give an extra dit/dah after every release of the paddle. I have not made any modifications to the radio, just added the resistors inside my paddle and moved the dah wire to the dit side of the jack (internal to the paddle). I'm no CW wiz, just a guy testing out his radio to make sure everything is working.? 73 Jason KB2SDR -- Best 73 KD8CEC / Ph.D ian lee kd8cec@... (my blog)
Joel Caulkins/N6ALT Member Profile All Messages By This Member #41818 Hi Ian, ?So what is the latest version of firmware? I down loaded 1.01 and installed it via Xloader, however when i turn on the uBITX it shows 1.00 on the display. Now I notice there is a version 1.02. Where do i get the latest greatest version? Thanks for doing this. Joel N6ALT
Philip G7JUR All Messages By This Member #41834 Hi Joel. Mine displays v1.01. I dont think v1.02 is out yet. Philip G7JUR
Ian Lee All Messages By This Member #41852 Joel I am very grateful for you to continue to use it since the initial version. Philip's answer is right. Please check the file name as shown below. At boot time, the message will be displayed as 1.01. And 1.02 is a minor change, so it is still before release. You can download the source before releasing it, but you do not need to. Ian KD8CEC 2018-02-14 0:46 GMT+09:00 Joel Caulkins <caulktel@...>: toggle quoted message Show quoted text Hi Ian, ?So what is the latest version of firmware? I down loaded 1.01 and installed it via Xloader, however when i turn on the uBITX it shows 1.00 on the display. Now I notice there is a version 1.02. Where do i get the latest greatest version? Thanks for doing this. Joel N6ALT -- Best 73 KD8CEC / Ph.D ian lee kd8cec@... (my blog)
Nick VK4PP All Messages By This Member #41854 HI Ian, Can we get the source for the latest version please? I need it to implement my TPA2016 and I2C display.... THanks,. 73 VK4PLN
Nick VK4PP All Messages By This Member #41855 I found it... thanks.
Ian Lee All Messages By This Member #41858 Nik Wait. I'll merge it to 1.02. Download it for 5 minutes. I have coded too much, so I do not have enough space. Please speak if you need more space for the program. I will exclude some features. Ian KD8CEC 2018-02-14 11:47 GMT+09:00 Nik VK4PLN <nickpullen@...>: toggle quoted message Show quoted text HI Ian, Can we get the source for the latest version please? I need it to implement my TPA2016 and I2C display.... THanks,. 73 VK4PLN -- Best 73 KD8CEC / Ph.D ian lee kd8cec@... (my blog)
Nick VK4PP All Messages By This Member #41859 Hi Ian, Yes, I did run out of space. I removed some code for the default HAM BANDS and that allowed me to include the extra for the I2C lCD and TPA2016... We need to test the hardware hack for the voltage meter for EPROM saving on poweroff then reduce the code more... lots to do... Great work from you so far, well done on an excellent version of the FW for the uBITX. 73.
Nick VK4PP All Messages By This Member #41860 Hi again. I think also the hardware hack version can save space by moving the keyers to dedicated digital pins freed up from the LCD to I2C mod. we can then remove all the analog input calibration code... 73
Ian Lee All Messages By This Member #41862 Nik I also tried to erase it first. I wish your project a success. Ian KD8CEC 2018-02-14 12:21 GMT+09:00 Nik VK4PLN <nickpullen@...>: toggle quoted message Show quoted text Hi again. I think also the hardware hack version can save space by moving the keyers to dedicated digital pins freed up from the LCD to I2C mod. we can then remove all the analog input calibration code... 73 -- Best 73 KD8CEC / Ph.D ian lee kd8cec@... (my blog)

Previous Topic Next Topic