开云体育

Mike replacing the regulator on the Radunio will not solve the heat problem. The regulator will source at least 1 amp to run everything that needs 5 Volts. The main problem is that if your supply

It *seems* - and someone please correct me, in the likely event that I am wrong, bilut it *seems* that the newest stock firmware is quite solid, and has incorporated many of the advantages of the

Mike, I run a 2.8" display on a stock v5 with just an added heatsink to the regulator.? You could go the extra step and add a series resistor to drop the 12+ volts (I am running 13.8) to a lower

Nick, If you scroll back through some of the earlier posts on this thread you will see that I have a very similar issue with my v6 that I just assembled in the last two weeks.? It is not as drastic

Hi Evan, QRPGuys' Dummy Load/Power Meter kit arrived. Built and attached. Handy piece of kit for QRP power levels. Anyhow, essentially it confirms the reading I received with the borrowed meter ie 18V

Thanks a lot, Bob! /s Now my wallet is a little lighter than before...

Yes, my V6 has a heat sink on the Raduino with the 7805. It still gets quite warm to the touch. So you think replacing the one on the Raduino would run both the V6 and the Nextion 5 inch display?

Justin Ok L1 0.5mm? 3 turns L2 to L7 0.8mm yes 100nf =0.1?f? on the button (s)? --> you have 3 buttons max On the match tandem, I think to use the wire the big 0.8 mm? or more (1 turn) that go in

Gerard - I also used the appropriate drill bits to wind the air-core coils. 1.? I wound with 3 turns.? The picture I have is a bit fuzzy but it looks like 3TY as well. 2.? All 6 toroids appeared to

Justin, Thank you for all the information. I just received a labeler from Amazon. The labels that I bought for it have a clear background with white lettering. I have a black case so we’ll see if it

Jerry, I did the tone tests on my ?BITX using an Elecraft 2T-gen with interesting results.? The max power output is now on 40meters, with 80 and 30 being just a little reduced.? This does point to

Justin, If you go on N7DDC site N7DDC-ATU-100-mini-and-extended-boards/README.md at master · Dfinitski/N7DDC-ATU-100-mini-and-extended-boards · GitHub (

Mike: I think you'll find the board, as shipped, is very reliable. What you're seeing a lot of here are people who want to modify the board in various ways. Jack, W8TEE

I use WSJT to zero beat WWV Set receiver to 9.999 MHz and adjust for carrier (which is obvious) to 1000 Hz Mike K5ESS Sent: Tuesday, March 30, 2021 10:55 AM To: [email protected] Subject: Re: [BITX20]

I may buy one of these just to open it up, So the guy that wrote the most of libraries and code is a ham from Braz il.?I don’t believe he’s getting a cent out of that work. Ricardo Caratti

My personal uBitx firmware has a menu entry to dump the contents of EEPROM out to the Arduino IDE serial monitor. It is unfortunate that the stock code does not include something like this, only takes

"The notes in github are just a bit over my head." This may be a little convoluted, if you are not familiar with avrdude.? ?Dhiru's software is a Python script to decode / encode? Avrdude is the

Evan, In addition to the L31,L32 filter, note that the emitter resistor in the 45mhz IF at R26 got reduced from 470 to 220 ohms, that would reduce the signal at TP1 when in CW mode. I'd tend to

Jerry, Thanks for the pointers. Mike N2MS

Jerry, Thank you for the information! I have 2 v4s and a v5, all that the power "dips" on 40meters compared to 20.? By that, I mean that 80meters puts out 14watts, 40 about 9 watts, and 20 about