开云体育

Hah - someone else who liked the red one, too, yesterday. Mike Y, KM5Z Dallas, Texas, USA

I got an unterminated cable from Signalink. Two leads to the speaker jack. Three leads to the 4-pin mic connector, mic, ground, PTT. Seems to work ok. tim ab0wr bv@... wrote:

may I ask why morse code was not used for the feedback? -Justin N2TOH

Alan, Disregard below regarding winding direction. What is important is that dot markings on the transformers be observed. Can be confusing with one turn windings. Mike K5ESS Sent: Sunday, April 15,

Alan, Winding direction shouldn’t matter for this circuit. Try reversing the diode on the port with the negative voltage. Mike K5ESS Sent: Sunday, April 15, 2018 9:57 AM To: [email protected]

Hi Don and John. Earth of meter placed on ground plane when i got negative reading i swapped red vm lead to earth and took the higher (8.64v now)reflected reading as forward, and the lower 0.68 as

Posting the STL's would be very helpful. Much easier to modify a design then to start from scratch for more complex shapes like this.

Thanks Rob and Ian, Ian, I just love love the work you have done for the group maximizing the uBitx. I was a bit slow to start getting my head wrapped around whether to use laser or memory manager or

I have the CEC ver 1.6 software loaded on my uBITX and having trouble with the keyer.? I'm using a Bencher single paddle key (don't want to go the iambic route).? Problem is that in IambicB mode I

Elliott , the instructions are not referring to AM broadcast band. They are referring to SW broadcast, WWV, or CHU. If you are using the stock software there is a upper and lower frequency limit built

It really isn't needed.? A direct USB connection for controlling the ubitX as an FT817 and two audio cables to your PC should be all you need.? That's what I do. Ron W7HD -- Ron W7HD - NAQCC#7587

You might try easydigi eBay <https://www.ebay.com/itm/Psk-31-EASY-DIGI-Sound-Card-Interface-PSK-RTTY-SSTV-NBEMS-JT-65-PCB-KIT/322873075639?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2060353.m2749.l2649>

Hi Alan, I need more information, please. What were you using for a dummy load? What were you driving it with? What were you measuring with? Where did you place the earth reference lead on your meter?

Vince I am watching your wonderful work. Embedding raspberry pi in uBITX is a wonderful thing. It will be the world's first HF radio with built-in FT-8 Protocol. It's great work. What does it look

Carpentry and Socketry for the uBITX | | | | | | | | | | | Carpentry and Socketry for the uBITX Radio electronics blog. Homebrew ham radio. SolderSmoke podcast. QRP | | |

Hi my first posting in this group. I just made my licence and I'm thinking about buying the ubitx transeiver.? What I didn't find is a tutorial to install a signalink-usb with the ubitx. Is there any

Hello Alan, To my understanding the direction of the winding is important as I expect the voltages to add/subtract in the bridge. I had to change mine around and I followed the hand drawing in regards

Tom, what case did you use? Thanks Tony Acta non Verba ________________________________ Sent: Sunday, March 25, 2018 7:42:41 PM To: [email protected] Subject: Re: [BITX20] ubitx mount question

The instructions say to tune to a known broadcast station to calibrate the clock. (How far off can the clock be from the factory?) What is the minimum frequency receivable with the factory firmware? I

Congrats Andy, It is a genuined need and appreciate your sincere effort. Like wise i also look forward for other differently abled persons' needs. Hopw sooner some one would come up for others too.