|
Re: BITX40 Pop Fix
OK, glad to hear you got it working Ted!
Now you can start adding some of the minor mods in order to enjoy the full capabilities of the software. The most important one that I'd recommend you to start with is adding the function button. See for details. Happy BitX-ing! 73 Allard PE1NWL |
|
Re: BITX40 Pop Fix
BevTed Stanier
开云体育Eureka!!!! ? I had never tried the “Old Bootloader” version of the ATMega328 and now with all the other things are setup properly it up loaded with no errors. Guess that means that the software has been updated to the latest rev. I understand that it has functionality that I won’t be able to use on this oddball version of the BITX40. Hopefully though this will improve the pop noise when switching from TX to Rx and Vicky verky as well as maybe other things. As this is an abandoned kit from another Ham and a very basic TRX, as well signal band single mode, I don’t want to put too much into it. May do some of the component mods for other fixes. I’ll put the thing back together now and see what happens. Thanks for all of your time and help. I’ll post the results. 73 and stay safe guys. Ted VA7CTA P.S. Hope I am not to optimistic. Hi. ? Sent from for Windows 10 ? From: Arv Evans
Sent: Wednesday, July 29, 2020 1:17 PM To: [email protected]p Subject: Re: [BITX20] BITX40 Pop Fix ? That reference to trying to sync an STK500 board is interesting.?? Big difference between the Nano and a very old (extinct...?)? STK500 development board. ? _._ ? On Wed, Jul 29, 2020 at 11:18 AM BevTed Stanier <bevtedstan@...> wrote:
? |
|
Re: BITX40 Pop Fix
That reference to trying to sync an STK500 board is interesting.?? Big difference between the Nano and a very old (extinct...?)? STK500 development board. _._ On Wed, Jul 29, 2020 at 11:18 AM BevTed Stanier <bevtedstan@...> wrote:
|
|
Re: Nano
Ted,
I did get the picture that time.? From it I would surmise 2 things: 1 - That you do have an HF Signals Raduino with a Nano Clone. 2 - That the Nano is soldered in on the opposite side of the Raduino board from the uBITX versions (the Nano is between the Raduino board and the Display). Attached are pictures of the Raduino shipped with the uBITX rigs: Note: I did add the heatsink on the Raduino Regulator and replaced the Nano with a clone bought through Amazon.? That way I could keep the Nano in the factory original state. If you ever decide to replace the Nano, I would move it to the other side of the board, unless you are mounting the display with a cable, then it would not matter.? The Nano replacement will be difficult with the two headers to desolder and all the pins to remove. The settings for the Arduino IDE that we have sent you before should work.? If not, you could try changing the processor to the standard ATMega328P without the Old Bootloader.? Other than that, replacing the Nano is the best option at this time. 73 Evan AC9TU |
|
Re: BITX40 Pop Fix
BevTed Stanier
开云体育Don’t know how this Group.IO stuff works so hope all see my msgs. 73 Ted? I appreciate all your efforts.!!! ? Sent from for Windows 10 ? From: Evan Hand
Sent: Wednesday, July 29, 2020 10:07 AM To: [email protected] Subject: Re: [BITX20] BITX40 Pop Fix ? Ted, ? |
|
Re: BITX40 Pop Fix
Jack, W8TEE
I think the Raduino is the name given to the display interface, which includes the Nano and the LCD display. If you are using software to upload to the Nano, Nano is the correct choice for the upload. Jack, W8TEE
On Wednesday, July 29, 2020, 1:39:31 PM EDT, BevTed Stanier <bevtedstan@...> wrote:
I did unplug the Nano from everything else and no change. Processors are?? ATMega328p, ATMega328p(Old Bootloader) and ATMega168 ATMega328p is selected. Should I try old bootloader?? Don’t see anything on the board except “NANO” I understand it is a Raduino ? Ted ? Sent from for Windows 10 ? From: Evan Hand
Sent: Wednesday, July 29, 2020 10:04 AM To: [email protected] Subject: Re: [BITX20] BITX40 Pop Fix ? Ted, Arduino Nano V3.0, Nano Board CH340/ATmega328P Without USB Cable, Compatible with Arduino Nano V3.0
|
|
Re: BITX40 Pop Fix
BevTed Stanier
开云体育I did unplug the Nano from everything else and no change. Processors are?? ATMega328p, ATMega328p(Old Bootloader) and ATMega168 ATMega328p is selected. Should I try old bootloader?? Don’t see anything on the board except “NANO” I understand it is a Raduino ? Ted ? Sent from for Windows 10 ? From: Evan Hand
Sent: Wednesday, July 29, 2020 10:04 AM To: [email protected] Subject: Re: [BITX20] BITX40 Pop Fix ? Ted, Arduino Nano V3.0, Nano Board CH340/ATmega328P Without USB Cable, Compatible with Arduino Nano V3.0
|
|
Re: BITX40 Pop Fix
BevTed Stanier
开云体育Yup that was set okay. ? Sent from for Windows 10 ? From: Allard PE1NWL
Sent: Wednesday, July 29, 2020 9:58 AM To: [email protected] Subject: Re: [BITX20] BITX40 Pop Fix ? Ted, ? |
|
Re: BITX40 Pop Fix
BevTed Stanier
开云体育Cable checks okay for continuity. Got verbose error msg. Arduino: 1.8.13 (Windows 10), Board: "Arduino Nano, ATmega328P" ? Sketch uses 22966 bytes (74%) of program storage space. Maximum is 30720 bytes. ? Global variables use 1320 bytes (64%) of dynamic memory, leaving 728 bytes for local variables. Maximum is 2048 bytes. ? C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avrdude -CC:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf -v -patmega328p -carduino -PCOM11 -b115200 -D -Uflash:w:C:\Users\BevTed\AppData\Local\Temp\arduino_build_23880/raduino_v1.29_bitx40.ino.hex:i ? ? ? avrdude: Version 6.3-20190619 ? ???????? Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/ ? ???????? Copyright (c) 2007-2014 Joerg Wunsch ? ? ? ???????? System wide configuration file is "C:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf" ? ? ? ???????? Using Port??????????????????? : COM11 ? ???????? Using Programmer????????????? : arduino ? ??????? ?Overriding Baud Rate????????? : 115200 ? avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x00 ? avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x00 ? avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x00 ? avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x00 ? avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x00 ? avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x00 ? avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x00 ? avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x00 ? avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x00 ? avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x00 ? ? ? avrdude done.? Thank you. ? ? ? An error occurred while uploading the sketch ? ? ? This report would have more information with "Show verbose output during compilation" option enabled in File -> Preferences. ? ? Don’t know what all this means?? ? TX and RX? LEDs do not flash when trying to upload. ? Ted ? ? Sent from for Windows 10 ? From: BevTed Stanier
Sent: Wednesday, July 29, 2020 8:52 AM To: [email protected] Subject: Re: [BITX20] BITX40 Pop Fix ? Evan Okay Comport set as you suggested. For some reason “Com&LPT” did not appear on Device Manager until I plugged in My Navigator and then the Nano. Something I set when setting the Navigator up, Anyway now have Com10 assigned. Tried the upload again with same results “sync error” “AVRDUDE;STK500_GETSYNC()? NOT IN SYNC” I will next check the cable with an ohm meter just to rule it out as a charge cable. Maybe it just won’t handle data freq.??? More later Ted ? Sent from for Windows 10 ? From: BevTed Stanier ? Evan ? Yes using Windows 10. Looks like I messed up the Comport setup but got the rest okay. Now getting a sync error when uploading so will go back and redo the Comport as you suggest. Will let you know the result. 73 Ted ? Sent from for Windows 10 ? From: [email protected] <[email protected]> on behalf of Evan Hand <elhandjr@...> ? Ted, ? ? |
Allard PE1NWL
