Cable checks okay for continuity.
Got verbose error msg.
Arduino: 1.8.13 (Windows 10), Board: "Arduino Nano, ATmega328P"
?
Sketch uses 22966 bytes (74%) of program storage space. Maximum is 30720 bytes.
?
Global variables use 1320 bytes (64%) of dynamic memory, leaving 728 bytes for local variables. Maximum is 2048 bytes.
?
C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avrdude -CC:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf -v -patmega328p -carduino -PCOM11 -b115200 -D -Uflash:w:C:\Users\BevTed\AppData\Local\Temp\arduino_build_23880/raduino_v1.29_bitx40.ino.hex:i
?
?
?
avrdude: Version 6.3-20190619
?
???????? Copyright (c) 2000-2005 Brian Dean,
?
???????? Copyright (c) 2007-2014 Joerg Wunsch
?
?
?
???????? System wide configuration file is "C:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf"
?
?
?
???????? Using Port??????????????????? : COM11
?
???????? Using Programmer????????????? : arduino
?
??????? ?Overriding Baud Rate????????? : 115200
?
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x00
?
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x00
?
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x00
?
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x00
?
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x00
?
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x00
?
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x00
?
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x00
?
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x00
?
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x00
?
?
?
avrdude done.? Thank you.
?
?
?
An error occurred while uploading the sketch
?
?
?
This report would have more information with
"Show verbose output during compilation"
option enabled in File -> Preferences.
?
?
Don¡¯t know what all this means??
?
TX and RX? LEDs do not flash when trying to upload.
?
Ted
?
?
Sent from for Windows 10
?
?
Evan
Okay Comport set as you suggested. For some reason ¡°Com&LPT¡± did not appear on Device Manager until I plugged in My Navigator and then the Nano. Something I set when setting the Navigator up, Anyway now have Com10 assigned.
Tried the upload again with same results ¡°sync error¡±
¡°AVRDUDE;STK500_GETSYNC()? NOT IN SYNC¡±
I will next check the cable with an ohm meter just to rule it out as a charge cable.
Maybe it just won¡¯t handle data freq.???
More later
Ted
?
Sent from for Windows 10
?
?
Evan
?
Yes using Windows 10. Looks like I messed up the Comport setup but got the rest okay.
Now getting a sync error when uploading so will go back and redo the Comport as you suggest.
Will let you know the result.
73
Ted
?
Sent from for Windows 10
?
