Thanks Ian, will try it out when I can.
Hope you get some assistance in writing/contributions to a user guide as per your request on your website.

On the ATMega328P that's on the Nano, pins A6 and A7 are analog inputs only.
The other analog pins can be used as digital pins.

Takes a pretty thorough read of the datasheet to figure that out.

Simple problem and I am stumped!

I wrote some test sketches to test the Analog Pins that are on the 8 Pin
molex?? called "Controls" on uBit.

Well on all 5 Nanos I have here, A6 and A7 don't want to flip. A really
puzzling thing is I have an old Mega 2560 (the one with the old USB
squarish plug), and its

A6 and A7 will toggle?

I learned one good thing in hours of fussing around.?? I did NOT know you
can use a Pin name in the sketch without "A" in front of it.

They simply call the ports up from the last digital pin (13), So A0 you
can call 14!!!?? WOW, never knew that.

What is it good for????? You can use for statements to increment a
counter (i) to initialize and address these pins.?? You don't have to put
A in there.



Please Help Me, I am going nuts!

Mike, WA6ISP

Here is a test of A0 - A7,?? MY A6 & A7 won't toggle on my Nanos?


//
// Test A0 - A7
byte i = 0;

void setup()?? {

for (int i=14; i<22; i++)?? {
???? pinMode(i, OUTPUT);
???? digitalWrite(i, HIGH);

}

}
void loop() {

?? for (int i=14; i<22; i++) {

?? digitalWrite(i, LOW);
?? delay(100);
?? digitalWrite(i, HIGH);
?? delay(100);
?? }


}


--
Mike Hagen, WA6ISP
10917 Bryant Street
Yucaipa, Ca. 92399
(909) 918-0058
PayPal ID "MotDog@..."
Mike@...

Or you can run direwolf on your pc directly.? I use it all the time with packet.

If RMS express can't handle it I would complain to the powers that be.

rOn

---

From: Joe Puma <kd2nfc@...>
To: [email protected]
Sent: Monday, March 5, 2018 1:14 PM
Subject: Re: [BITX20] Fldigi with UBITX

Walter have you tried dire wolf on the Rpi? You would still need to run RMS express on the laptop but you can connect to the RPI as a TNC modem using KISS. That’s how my winlink set up works at the moment

Joe

KD2NFC?

On Mar 5, 2018, at 8:59 AM, Walter <W9KJO@...> wrote:

On Mon, Mar 5, 2018 at 04:57 am, Charles Ayers wrote:

What are you running FLDigi on?? A Win/PC, Linux/PC, or something like a Raspberry Pi?
Curious how many folks are running FLDigi on Ras-Pi because that's what I'm working to integrate into a field-portable station with my uBitX right now.

Thanks
Chuck (N1KGY)

I have a Pi3 that runs Fldigi with no problems.? However RMS Express will not run on a Pi.? So I abandoned the Pi3 for a laptop.? My laptop, running Win 7 will run indefinitely on my solar system with the no RMI problems charger I built for charging the laptop.? Since I have solar setup for both my QTH and my Mobile I have a reliable portable solution for both situations.

Plus I'm not real good at Linux programming and have been frustrated with three different books I purchased to learn the protocol.? It was hard just getting Flamp loaded and running due to my lack of knowledge in Raspbian or Linux.? So Windows is far easier to load up software and the frequent updates that come with Fldigi, Flmsg, and Flamp.

--
73, W9KJO
Walter