开云体育

Glad I could help. WSJT-X is working well, even though the cat tests are not. I have made plenty of contacts with it Hmmm, maybe I will try WSJT-z for the sbitx I had it running on my

I want filters: be able to toggle between everything and unique CQs only, at least (back and forth dynamically, not only for incoming packets the way WSJT-X does). Maybe eventually other filters,

I think asking/expecting/hoping HF Signals will track, calculate, collect and report tax/duty fees for the countries they ship to is a big ask. I suspect if HF Signals were to undertake such an

I suspect your powersupply is shutting down. 3.4 watt on sbit is fine for ft8 However, if you try to drive with the same tx level when in digi mode , your sbitx will now put out much much higher

Indeed. DHL is bad about this, and also bad about doing home delivery (usually they drop off packages at a nearby gas station and I have to drive over there and pick them up). I picked up the

The bottom line problem was wsjt-x power slider defaults to maximum. This turned out to be a current draw issue that was causing the zbitx to reboot Thanks to all for your input and help resolving

You hit the nail on the head about current draw though The reboot was caused by the power slider in wsjt-x. Thanks Leo, AI5II [email protected]> wrote:

If I turn TUNE on in the zbitx panel while in digi mode, the zbitx outputs 3.4W. If I click on Tune in wsjt-x the zbitx reboots Leo, AI5II [email protected]> wrote:

I would put a new image on a new microsd v2 A1 . Sandisk extreme or equivalent. Just to be sure the card is not the issue. Also when using Digi mode , the tx pwr out audio will drive yor zbitx to the

Yes. Sorry it is working. I have to update the firmware. Thanks to all null [email protected]> wrote:

Hello Ragav and the sales team It was my fault not sending to the correct e-mail address, sorry for that. So can you please cancel my order and refund me, as I ask below. Thankyou 73 Ian C Frith

Hi, just tested my zbitx with 9v ps and 2 w output and 20% rate in wspr. Backplate got extremly hot that I was able to hold it in hands for less than 5 seconds, what means over70 degree c out of my

Nomar, The Rpi takes about 15-20 seconds after powering on to boot up. Are you able to see the desktop environment when you connect the zBitx to a HDMI display? 73, Ragav

Ian, We haven't received the email, just checked for your name and callsign in the inbox but didn't find any. Can you please resend it to sales at hfsignals dot com and mark support at hfsignals dot

I did a clean install without any updates with wsjt-x running, I can change bands without any problem; BUT "Test CAT" does nothing and if I click on "Enable TX" the zbitx reboots and if I click on

I downloaded a new image. No update/upgrade CAT changes frequencies with wsjtx Doing a check CAT does nothing Clicking Tune in wsjtx causes my zbitx to reboot Leo, AI5II

This is DI1ZC My ZBTIX open the display but won’t boot up. Only starting display is seen Sent By: DU1ZC / KA4ZCC 73' Nomar

Hi Ken, thanks So like through email: ve3slj at myrac? .ca ? ( ve3slj@... )

Aaron You should on JJ’s discord. ?He leads 64 bit dev team. ?Try upgrading to JJs 64 bit software. ?The complete img is on his git hub. https://github.com/drexjj/sbitx Many of the features

Yes the zbitx runs too hot. ?The linear regulator will make the back plate hot even while sitting idle but still reasonable. ?72c is not too hot for the zero as it’s under the thermal throttle