Re: Spectrum display window bug
#zbitx
Yes, i did resolve it. I thought i had documented or taken pictures of the settings.
I am looking thru my old paper work.
( I have sold the Sbitx a while back so don't have it to compare to)
Hmm maybe even in one of my emails. Checking
Joe VE1BWV?
Joel, if I remember correctly, you had a CAT problem with wsjtx back in the 32-bit era. Did you manage to fix it?
--
Gyula HA3HZ
|
Re: Spectrum display window bug
#zbitx
Joel, if I remember correctly, you had a CAT problem with wsjtx back in the 32-bit era. Did you manage to fix it?
--
Gyula HA3HZ
|
Re: #zBitx Tilt Stand for zBitx anyone?
#zbitx
2PCS Zinc Alloy Mini Foldable Laptop Stand, Portable Computer Keyboard Riser with 2 Adjustable Angles, Self-Adhesive Invisible Notebook Stand and Keyboard Lift for Desk (Black)
This works great for my zBitx.? Bill AG5ZN
Hi Pete,
???? I'm using a small calculator stand, because I haven't found anything better yet. But actually it seems to work well.
--Ed, N3CW--
|
Re: Homebrew satellite control system that can run on sBitx
Some additional careful measurements with a spectrum analyzer, tracking generator and calibrated attenuators, the outside antenna, and such.?
?
the sensitivity of the sbitx on 10m seems right in line with typical HF receivers without a preamp. It was designed for maximum dynamic range! ?
working with the $165 Ukrainian transverter looks like I am almost to the noise figure/sensitivity that I need. ? Adding 10 DB or so of low noise preamplifier gain in front should make a great deal of improvement.
?
the $120 preamp on DX engine engineering looks like a good possibility of success. So it is ordered and we’ll see what happens!
?
I have the advantage that I’m not going to be transmitting into the same antenna, and I will put a diplexer in ?front of the receive preamp anyway to help protect ?
?
Gordon Kx4z?
?
?
|
Re: Unable to Update Pi Zero
OK...the brute force approach was needed.? Image written on a new card seems to have fixed the problem.
--Ed, N3CW--
?
|
Re: Unable to Update Pi Zero
Hi Gyula,
???? I have burned the image file onto a new card.? But how do I get to the old card to replace it?? I removed the four case mounting screws but there are three more nuts on the bottom metal plate that just spin without loosening.
--Ed, N3CW--
?
|
Re: #zBitx Tilt Stand for zBitx anyone?
#zbitx
Hi Pete,
???? I'm using a small calculator stand, because I haven't found anything better yet. But actually it seems to work well.
--Ed, N3CW--
|
Re: zbitx - No Tx on WSJTX?
I am able to use grig to change the zbitx frequencies if I start grig with:?
grig -m 2 -r
so my optinion is that there is something missing from the zbitx hamlib.c?
Leo? AI5II
Same issue here. I am looking for the settings I used on my Sbitx, to see if that?helps.
As you indicated ft8 rx is working TX or any cat commands don't work
Joe VE1BWV?
On Fri, Apr 4, 2025, 9:00?a.m. Chris Bolton via <boltonbicycles= [email protected]> wrote: I have WSJTX running nicely on a 2nd monitor on the zbitx except that it is failing to trigger Tx with a hamlib error shown in the terminal window?
?
Can anyone share their working WSJTX radio config for the zbitx?
?
Many Thanks
?
Chris?
?
?
|
Re: Wifi Alternate - Can you copy wpa_supplicant.conf into boot folder to get wifi?
Could be. I never knew such a thing existed. I guess I should get one of those. Also a USB-C one (which I definitely knew about).?
--
Buddy Brannan, KB5ELV, WRVB670?-?Erie, PA
Email: buddy@...
Mobile: (814) 431-0962
toggle quoted message
Show quoted text
On Apr 7, 2025, at 1:21?PM, Ken N2VIP <ken@...> wrote:
Wouldn't a micro usb Ethernet adapter work also? Allowing you to access internal RPi?
? Ken, N2VIP On Apr 7, 2025, at 7:57?AM, Jeff Kelly via groups.io <jkelly@...> wrote:
Not that it is any easier, but if you don't have an HDMI adapter etc.,
can you open the radio, pull the microsd card, and copy a
wpa_supplicant.conf file into boot folder with your SSID and PW to get wifi going?
?
Jeff
|
Re: Homebrew satellite control system that can run on sBitx
I'm just a sucker for trying to use the least expensive gear....so even though the sBitx / transverter system just couldn't create enough sensitivity.... I ordered a GaAs FET preamp with up to 20dB gain in hopes of making the sBitx work on this project!
?
Here is the schematic of the board I made for controlling azimuth +/- elevator rotators:
?
?
Boards will eventually be available via a project on pcbway.com
?
Gordon KX4Z
?
?
|
Re: zbitx - No Tx on WSJTX?
Same issue here. I am looking for the settings I used on my Sbitx, to see if that?helps.
As you indicated ft8 rx is working TX or any cat commands don't work
Joe VE1BWV?
On Fri, Apr 4, 2025, 9:00?a.m. Chris Bolton via <boltonbicycles= [email protected]> wrote: I have WSJTX running nicely on a 2nd monitor on the zbitx except that it is failing to trigger Tx with a hamlib error shown in the terminal window?
?
Can anyone share their working WSJTX radio config for the zbitx?
?
Many Thanks
?
Chris?
?
?
|
probably impossible since the IF is around 40MHz
use a transverter
|
Re: Wifi Alternate - Can you copy wpa_supplicant.conf into boot folder to get wifi?
Wouldn't a micro usb Ethernet adapter work also? Allowing you to access internal RPi?
?
toggle quoted message
Show quoted text
On Apr 7, 2025, at 7:57?AM, Jeff Kelly via groups.io <jkelly@...> wrote:
Not that it is any easier, but if you don't have an HDMI adapter etc.,
can you open the radio, pull the microsd card, and copy a
wpa_supplicant.conf file into boot folder with your SSID and PW to get wifi going?
?
Jeff
|
Gary,
Hope dies last because you've read a lot about it but haven't seen it in action.
This device is an RPi-controlled SDR radio, packed as small as possible, with its advantages and disadvantages.
Not all options installed on the board work, and several applications work differently than you've seen so far.
--
Gyula HA3HZ
|
Re: Wifi Alternate - Can you copy wpa_supplicant.conf into boot folder to get wifi?
I’ve had the same question for some time. For reasons, local access to the Pi, at least initially, is going to be difficult to impossible for me otherwise.
--
Buddy Brannan, KB5ELV, WRVB670?-?Erie, PA
Email: buddy@...
Mobile: (814) 431-0962
toggle quoted message
Show quoted text
On Apr 7, 2025, at 8:57?AM, Jeff Kelly via groups.io <jkelly@...> wrote:
Not that it is any easier, but if you don't have an HDMI adapter etc.,
can you open the radio, pull the microsd card, and copy a
wpa_supplicant.conf file into boot folder with your SSID and PW to get wifi going?
?
Jeff
|
Re: Unable to Update Pi Zero
If nothing works, download the Image, extract it to .img format (32GB), copy it to a good quality uSD card with balenaEtcher and use that. This has the latest version.
--
Gyula HA3HZ
|
Re: Unable to Update Pi Zero
I copied the zbitx Image today because I was curious about a problem. I have sbitx v2, the hardware is different, and the program logged in fine after starting it.
If you changed the password in the RPi menu-> Preferences -> Raspberry Pi Configuration settings, use that.
It does not ask for a password to enter the terminal. I do not see a link in the manual to ask for a password.
--
Gyula HA3HZ
|
Re: Unable to Update Pi Zero
Password
hf12345
?
user
pi
|
Re: Unable to Update Pi Zero
Try using "raspberry", that looks like the password for the Rasberry Pi itself.
?
?
Thank you
Jim
KE0VVU
|
Just joined the group.? I ordered
my zBitx on Friday....on the 4 week waiting list.? Looking
forward to playing with this radio.? I belong to a group in
Chandler, AZ called "BE-HIP" (Hams In Parks).? We take our
portable radios out to local parks and setup our stations.? This
radio is perfect for that.? I am not the big of an FT8 fan, but
with it built into the rig, it makes it much easier than
dragging my laptop and support cables out to the park.?
Currently I am on the upper end of the price spectrum with a
KX2....
--
"POWER, WE DON'T NEED NO STICKIN' POWER" - EVERY KX2 OWNER
Always respect the airwaves,
73 de KI7PBR, Gary
|
HA3HZ
Bill AG5ZN
Gary-KI7PBR