¿ªÔÆÌåÓý

  1. BITX20
  2. Messages
Expanded Topics Messages Polls
Date
Re: #bitx40help #bitx40 #bitx40help #bitx40

 

Thanks for the reply Jerry!! I do not have a scope or really the in depth knowledge to use one.? I did try to upload the firmware back to the raduino and that was successful.I guess there is no harm in me trying to replace the arduino, I don't think I can break it any more than it already is.? I just wish I knew exactly what I did to cause the issue so I dont do it again.? would wiring the TX RX without the button have caused the problem?? I re wired that part with the button - Currently I have the black and brown wire from the PTT jack on the board going to the switch, then I have a black and brown wiring going to the outside pins of the transistor, the middle wire goes to a 4k7 resistor and to the raduino pin.? ?I was pretty happy that I pulled of the build without destorying it until the last step so I dont want to destroy another one LOL

Brian
Re: Broke it like only a newbie can - Calibration problems

[email protected]
 

and lastly -- sorry to not get this all into one message, hopefully it makes sense -- my BFO setting is 11.055.500.? The boards may vary some in production but if you put my numbers in for your master cal and BFO you should start hearing something, it should be close.

--Ron
K0EIA
Re: Broke it like only a newbie can - Calibration problems

[email protected]
 

Aha, I missed that you already have the uBitx manager.? It really simplifies your calibration work.? You can put in a number like 131630 for master calibration and that should get you close (that's what my master calibration is set at).

--Ron
K0EIA
Re: Broke it like only a newbie can - Calibration problems

[email protected]
 

Welcome to the world of fixing your own radio!? I had a very similar problem when I first loaded the CEC v1.122, I was confused by the calibration and BFO settings.? You probably lost your calibration when you loaded the new CEC firmware, so you need to recalibrate, and the calibration method is not the same as the stock firmware.??

Likewise your firmware load lost your BFO setting.? I also was confused by the default BFO setting of 11.997.000 in the CEC firmware.? That's just a default number, and it belongs with the older crystal filter (which was 12MHz).? Your v5 has the 11.059MHz crystals -- you can verify this by looking at the number on the cans, the ladder filter is the line of little oval shiny stainless steel crystals.? Put your 11.053.400 number in for BFO.

Good luck!
--Ron
K0EIA
Re: #bitx40help #bitx40 #bitx40help #bitx40

 

Brian,

I'd guess the Arduino Nano died.
Can you still upload new firmware to the Nano?
The good news is that they cost as little as 3 dollars, and are socketed on the Raduino to be easily replaced (since mid 2018).

Do you have a scope?
You might check to see if CLK2 into the DDS1 connector has a proper VFO signal, should be around 4.8mhz.
Alternately, listen for a 4.8mhz carrier on a nearby shortwave receiver.
(Could be off by a couple hundred khz, depends on the operating freq saved to EEPROM.)
If the 4.8mhz VFO is there, then the Nano is at least doing something.

The wiring harnesses on the Bitx40 have a bunch of wires flying around loose.
Some of those wires are quite dangerous, such as the loose wire from the Raduino that has 12v on it.
If the end of such a wire touches the wrong thing, it can destroy the Nano (or something else).
Best to either tape over the ends of those wires, or remove the wire from the connector
by pressing the retaining clip at the connector with a sharp tool while tugging lightly at the wire.

The Nano clones being so cheap, some simply fail due to poor quality control.
For example, some of the Nano's work, but draw 10x the supply current that they should.?
For a while.

The wiring instructions and diagrams that Allard provides
? ??
are pretty good.? I don't think I could describe that wiring any better.

Jerry, KE7ER


On Wed, Apr 3, 2019 at 08:03 AM, <hockeydad42@...> wrote:
Something happened when adding RX-TX or the straight key and my radio no longer receives.? If I press the PTT button, it sounds like it is transmitting so my uneducated guess is that the Raduino is broken.? No display on LCD (Does light when PTT is pressed), no? tuning clicks no receive audio other than a hiss.?

Re: Broke it like only a newbie can - Calibration problems

 


I gave that a try and it doesn't give me the option to reset it. It opens up with the "Set Tune Step" menu.
Re: QRP ATU for sale

 

Hi Adrian

Delivery to Estonia $15.
Payment with Paypal

Gilles F1BFU /FR

Le?mer. 3 avr. 2019 ¨¤?17:30, Adrian <adrian.blake@...> a ¨¦crit?:
Hi,
Do you have an estimate of delivery to Estonia?
Adrian

On Wed, Apr 3, 2019 at 6:20 PM F1BFU - Fr - 79 <gilles.f1bfu@...> wrote:
Hello

UHF Connectors.

Gilles F1BFU /FR

Le?mer. 3 avr. 2019 ¨¤?17:18, Adrian <adrian.blake@...> a ¨¦crit?:
Yes, interested, BNC or UHF connectors?

Adrian

On Wed, Apr 3, 2019 at 5:58 PM F1BFU - Fr - 79 <gilles.f1bfu@...> wrote:

For ale a Antenna?tuner QRP ZM-2 ATU EMTEC bought October 2018. Little served. 90 dollards. Preferably Europe.

F1BFU /FR



--
Adrian Blake, VK2ALF
101 Mulach St
Cooma, NSW, 2630
Australia
Mobile +61 407232978

P?rna tn 3
Otep??
Valga
Estonia
Mobile +372 51971441

--
Adrian
VK2ALF
Cooma, Australia & Otep??, Estonia



--
Adrian Blake, VK2ALF
101 Mulach St
Cooma, NSW, 2630
Australia
Mobile +61 407232978

P?rna tn 3
Otep??
Valga
Estonia
Mobile +372 51971441

--
Adrian
VK2ALF
Cooma, Australia & Otep??, Estonia

Re: QRP ATU for sale

 

Hi,
Do you have an estimate of delivery to Estonia?
Adrian

On Wed, Apr 3, 2019 at 6:20 PM F1BFU - Fr - 79 <gilles.f1bfu@...> wrote:
Hello

UHF Connectors.

Gilles F1BFU /FR

Le?mer. 3 avr. 2019 ¨¤?17:18, Adrian <adrian.blake@...> a ¨¦crit?:
Yes, interested, BNC or UHF connectors?

Adrian

On Wed, Apr 3, 2019 at 5:58 PM F1BFU - Fr - 79 <gilles.f1bfu@...> wrote:

For ale a Antenna?tuner QRP ZM-2 ATU EMTEC bought October 2018. Little served. 90 dollards. Preferably Europe.

F1BFU /FR



--
Adrian Blake, VK2ALF
101 Mulach St
Cooma, NSW, 2630
Australia
Mobile +61 407232978

P?rna tn 3
Otep??
Valga
Estonia
Mobile +372 51971441

--
Adrian
VK2ALF
Cooma, Australia & Otep??, Estonia



--
Adrian Blake, VK2ALF
101 Mulach St
Cooma, NSW, 2630
Australia
Mobile +61 407232978

P?rna tn 3
Otep??
Valga
Estonia
Mobile +372 51971441

--
Adrian
VK2ALF
Cooma, Australia & Otep??, Estonia
New Arrivals Universal Case for uBitx- Nextion

 

We have been providing the uBitx case for Nextion 2.4 Inch And 2.8 Displays as well as 3.5 Inch And 5 Inch Displays Case.
New arrivals are for 3.2 Inch Nextion Display and 4.3 Inch Display colors Texture Black, Light Green with Black faceplates. And Blue and White.
3.2 Inch Nextion Display and 4.3 Inch Display case are not listed on our website as yet due to clearing of back log orders.
If any one requires the case not listed can email us.

Hope friends who purchased the 3.5 Inch And 5 Inch Display case have had a good experience building uBitx in our case.

Thanks to all and best regards

Sunil vu3sua
Re: Broke it like only a newbie can - Calibration problems

Laurence Oberman
 

press the encoder and hold it pressed, Power on,
choose factory defaults

On Wed, Apr 3, 2019 at 11:14 AM Wiley1 <whoward962@...> wrote:

I am a complete newbie so it was only a matter of time before I broke something good. I have a V5 uBitx running CEC 1.22 software with a 3.5" Nextion screen. I had everything working fairly well. I heard a CQ from Norway last weekend and I am in Michigan. Anyway I kept trying to tune it a little better. The next time I turned the radio on I was way out of adjustment. I cannot get it to tune back in. I downloaded the CEC1.22 and now my BFO reads 11.997.000. when everything was working it was at 11.053.400. Better late than never I am now using uBitx manager and when I read from the radio it shows the BFO as 11.053.400. Is there a way to work out of this? I do have the uBitx file if it helps.

Thanks
KE8EYM
Re: QRP ATU for sale

 

Hello

UHF Connectors.

Gilles F1BFU /FR

Le?mer. 3 avr. 2019 ¨¤?17:18, Adrian <adrian.blake@...> a ¨¦crit?:
Yes, interested, BNC or UHF connectors?

Adrian

On Wed, Apr 3, 2019 at 5:58 PM F1BFU - Fr - 79 <gilles.f1bfu@...> wrote:

For ale a Antenna?tuner QRP ZM-2 ATU EMTEC bought October 2018. Little served. 90 dollards. Preferably Europe.

F1BFU /FR



--
Adrian Blake, VK2ALF
101 Mulach St
Cooma, NSW, 2630
Australia
Mobile +61 407232978

P?rna tn 3
Otep??
Valga
Estonia
Mobile +372 51971441

--
Adrian
VK2ALF
Cooma, Australia & Otep??, Estonia

Re: QRP ATU for sale

 

Yes, interested, BNC or UHF connectors?

Adrian

On Wed, Apr 3, 2019 at 5:58 PM F1BFU - Fr - 79 <gilles.f1bfu@...> wrote:

For ale a Antenna?tuner QRP ZM-2 ATU EMTEC bought October 2018. Little served. 90 dollards. Preferably Europe.

F1BFU /FR



--
Adrian Blake, VK2ALF
101 Mulach St
Cooma, NSW, 2630
Australia
Mobile +61 407232978

P?rna tn 3
Otep??
Valga
Estonia
Mobile +372 51971441

--
Adrian
VK2ALF
Cooma, Australia & Otep??, Estonia
Re: v5 Alive! (plus my advice, and thanks)

 

Here's another post from Raj, affirming that he was using a yellow S+M brand 1210 inductor.
??/g/BITX20/message/60678

Here, Raj says that TDK-EPCOS parts work as well? (EPCOS was bought out by TDK).
??/g/BITX20/message/61261

Unfortunately, I don't see any complete part numbers in any forum posts
from somebody who has verified with a spectrum analyzer that spurs were reduced.

I bought a similar assortment of TDK-EPCOS-Murata parts from ebay,
have not verified results with a spectrum analyzer.
The parts they actually ship may vary with the parts they can find.
But here's what they shipped to me
480pcs inductor coil size 1210 1008 (24x20pcs) EPCOS TDK MURATA
B82422A3470J 47nH 1210 EPCOS? 20pcs
B82422A3101K 100nH 1210 EPCOS? 20pcs
NL322522TR120K 120nH 1210 TDK? 20pcs
B82412A3181K 180nH 1210 EPCOS 20pcs
1008CS221XG 220nH 1008 COILCRAFT 20pcs
B82422A3331K 330nH 1210 EPCOS 20pcs
B82422A3471J 470nH 1210 EPCOS 20pcs
NL322522TR56J 560nH 1210 TDK? 20pcs
B82422A3681K 680nH 1210 EPCOS 20pcs
NL322522TR82J 820nH 1210 TDK? 20pcs
B82412A1102K 1uH? 1210 EPCOS? 20pcs
FSLM2520-1R5J 1.5uH 1008 TOKO? 20pcs
B82412A1222K 2.2uH 1210 EPCOS 20pcs
NL322522T3R3J 3.3uH 1210 TDK? 20pcs
B82422T1472K 4.7uH 1210 EPCOS 20pcs
B82412A1562K 5.6uH 1210 EPCOS 20pcs
NLV25T6R8J 6.8uH 1008 TDK 20pcs
B82422A1822K 8.2uH 1210 EPCOS 20pcs
NLV25T120J? ?12uH? 1008 TDK? ?20pcs
NL322522T270J? 27uH 1210 TDK? 20pcs
NLV25T330J? ?33uH 1008 TDK? ? 20pcs
NLV25T680J? ?68uH? 1008 TDK? ?20pcs
B82422A1104K 100uH 1210 EPCOS 20pcs
NL322522T121J 120uH 1210 TDK? ? 20pcs
?


Farhan chose a different method of fixing spurs on the v5 uBitx,
primarily the low pass filter at L31, L32, C205 near the first mixer.
That filter removes the 90mhz second harmonic coming out of the 45mhz IF amp.
Other possibly significant changes on v5 with regard to spurs would be the BFR93W's
at Q20,21,22? (were MMBT3904's) and the move to 220 ohms at R26 (was 470).

Jerry


On Wed, Apr 3, 2019 at 07:05 AM, Jerry Gaffke wrote:
Here's the post from Raj giving results for various inductor types at L5,L7:
? ??/g/BITX20/message/60946
Broke it like only a newbie can - Calibration problems

 

I am a complete newbie so it was only a matter of time before I broke something good. I have a V5 uBitx running CEC 1.22 software with a 3.5" Nextion screen. I had everything working fairly well. I heard a CQ from Norway last weekend and I am in Michigan. Anyway I kept trying to tune it a little better. The next time I turned the radio on I was way out of adjustment. I cannot get it to tune back in. I downloaded the CEC1.22 and now my BFO reads 11.997.000. when everything was working it was at 11.053.400. Better late than never I am now using uBitx manager and when I read from the radio it shows the BFO as 11.053.400. Is there a way to work out of this? I do have the uBitx file if it helps.

Thanks
KE8EYM
For sale Bitx HBRIHF

 

Sorry I forgot the pictures


---------- Forwarded message ---------
De?: F1BFU - Fr - 79 via Groups.Io <gilles.f1bfu=[email protected]>
Date: mer. 3 avr. 2019 ¨¤?17:03
Subject: [BITX20] For sale Bitx HBRIHF
To: <[email protected]>



For sale transceiver 40m (7mHz) HBR1HF?
*. SSB & CW modes
*. 2x IRF 530 PA
*. 25 watts HF
*. Dimensions 150 x 150 x 56 mm for use in mobile or portable

The set includes:
*. The HBR1HF transceiver
*. The microphone
*. The DC cord
Preferably Europe
$ 110 plus transportation

Gilles F1BFU /FR

IMAG0568.jpg
IMAG0571.jpg

Re: New software CEC v1.2 #bitx20

 

GitHub address for phdlee fork of ubitx
#bitx40help #bitx40 #bitx40help #bitx40

 

I am very new to homebrew electronics and was thrilled when I built a working Bitx40 right off the bat.? I did several mods and tested each one along the way.? I was feeling quite confident.? I upgraded to raduino_v1.28.1 and installed the Function Button, PTT, CW carrier all without issue.? As I am learning Morse I really wanted to add CW.? Something happened when adding RX-TX or the straight key and my radio no longer receives.? If I press the PTT button, it sounds like it is transmitting so my uneducated guess is that the Raduino is broken.? No display on LCD (Does light when PTT is pressed), no? tuning clicks no receive audio other than a hiss.? It really was the last step before I found a case for the radio.? I ordered a new kit, but I don¡¯t know exactly what I did to break the device.? I do know that I wired the RX-TX WITHOUT the ptt button.? The straight key I wired to the raduino and then to the main ground.? I am not 100% sure If I did both of these mods at the same time or not.? Can anyone show a picture or describe their RX-TX and Straight Key wiring?? I want to rebuild, but do not want to make the same mistake twice.
Thanks
Brian
For sale Bitx HBRIHF

 


For sale transceiver 40m (7mHz) HBR1HF?
*. SSB & CW modes
*. 2x IRF 530 PA
*. 25 watts HF
*. Dimensions 150 x 150 x 56 mm for use in mobile or portable

The set includes:
*. The HBR1HF transceiver
*. The microphone
*. The DC cord
Preferably Europe
$ 110 plus transportation

Gilles F1BFU /FR
QRP ATU for sale

 


For ale a Antenna?tuner QRP ZM-2 ATU EMTEC bought October 2018. Little served. 90 dollards. Preferably Europe.

F1BFU /FR
Re: RIT

Jack Purdum
 

I would imagine that things are getting a little crowded in the CEC software. I don't know how much room is left.

Jack, W8TEE

On Wednesday, April 3, 2019, 10:26:37 AM EDT, Sam Tedesco <stedesco619@...> wrote:


I'm using cec 1.097 and a nextion. I removed most of the stock junk on the tft so I can custom build for cw. I like my main tuning step at 1khz and my RIT at 1hz. Anyway, using a button control, I present the available tune steps. The problem is that any command to the nano resets the screen. So, I can select the 1hz, and use the rit...but, I lose any button controls...i.e. button.txt, button.color, etc. If I hit the button again, it presents the tune steps and turns off the rit. I just can't tell if the rit is on or not. Is there a control that isn't affected by a reset?

49301 - 49320 of 116186