开云体育

Eric, thank you very much for performing that test. I read through your code and I think that you are calling modem poll on every tick. That would certainly suggest that your newfound success

I think Gordon KX4Z is spot on, the timing of items in the ui_tick() loop need adjusting. I slowed down a few things, and made polling the key more frequent, and now I was able to send at 30WPM (not

I had a 20M SSB contact with NC from Chicago (640 miles)- got a 1/1 signal report but was able to exchange call signs and name. I think I have a slight amount of desense so probably need to work on

Hello Rick, There are two versions of the Nano's boot loader: one for original miniUSB-connected devices and the other for USB-C devices. This is a generalization, so there can be exceptions. The

Is there a reason you didn't start a new thread for your very specific request for technical assistance from Ashar? Farhan may not see your question, since the subject line is about an SK ham... Ken,

Ashhar -- We are having issues programming the NANO (Rabuino) with KD8cec software for the V5 and V6 Ubitx. IS there a particular version of the NANO we should be looking for. Thanks for your time --

Try this. I have seen this happen. Select the mode and don't keep clicking it with the stylus. But highlight the mode and then use the knob to go up or down to select the mode. Should bring up the

I'm sorry, but I don't know much about the sbitx application used by zbitx. Why didn't it become zbitx? Among the questions is sbitx v3, which cannot update v3.051. The name is unfortunate. If you

Has anyone found or devised a suitable tilt stand for the zBitx? The rear panel is a heat sink so likely stick-on tilt feet would become "unstuck" with the heat. I'd be interested in what users have

Already did this. Still does not transmit Leo, AI5II wrote:

I just wrote to a questioner where you can get more knowledge and read the topic: *New sBitx V3 to me* ( /g/BITX20/topic/new_sbitx_v3_to_me/111987114 ) -- Gyula HA3HZ

I haven’t updated the v2 since I got it about 2 years ago. I understand it’s possible to load v3 on it, but the update procedure in the manual doesn’t work. Is there a step-by -step procedure

Andrew, You can read about cw on zbitx in the forum search, but don't expect a quick solution. The situation is better on 64-bit sbitx. -- Gyula HA3HZ

Steve, if I understand correctly, you have sBitx v3 hardware. I recommend upgrading to 64-bit, the forum discussion for which can be found here: *New sBitx V3 to me (

Got my zbitx updated. Cells charged. FT8 working but no qso as yet. Tring cw mode. Can't make any sense of decodes a stream of T & E which I suppose is to be expected. Tried different wpm to no

The description of point 10 of Digitalis mode on page 21 in zBitx-User-Manual-.pdf is incorrect. It should read as follows: 10. Choose plughw:CARD=Loopback *_1,* DEV=0 as the Output/Playback

Device manufacturers typically install the cheapest available components. If someone is bothered by the quality of the component, they will replace it with the one that suits them best! This is just

The cable provided with the zBitx has a connector on the end which I would describe as a "crab claw" contact to mate with the female connector center pin. In my opinion, I would say the "claws" would

Leo, I can't write any helpful information for your problem because I don't know where and how the sbitx and zbitx programs are separated. What was transferred from sbitx and it's also confusing to

I tried to update my sBitx but got the error message below. ?I checked the sbitx directory and found “oled.c” instead. Please advise how to update my sBitx V3. Thanks, Steve WE5K