开云体育

Mike: I think you'll find the board, as shipped, is very reliable. What you're seeing a lot of here are people who want to modify the board in various ways. Jack, W8TEE

I use WSJT to zero beat WWV Set receiver to 9.999 MHz and adjust for carrier (which is obvious) to 1000 Hz Mike K5ESS Sent: Tuesday, March 30, 2021 10:55 AM To: [email protected] Subject: Re: [BITX20]

I may buy one of these just to open it up, So the guy that wrote the most of libraries and code is a ham from Braz il.?I don’t believe he’s getting a cent out of that work. Ricardo Caratti

My personal uBitx firmware has a menu entry to dump the contents of EEPROM out to the Arduino IDE serial monitor. It is unfortunate that the stock code does not include something like this, only takes

"The notes in github are just a bit over my head." This may be a little convoluted, if you are not familiar with avrdude.? ?Dhiru's software is a Python script to decode / encode? Avrdude is the

Evan, In addition to the L31,L32 filter, note that the emitter resistor in the 45mhz IF at R26 got reduced from 470 to 220 ohms, that would reduce the signal at TP1 when in CW mode. I'd tend to

Jerry, Thanks for the pointers. Mike N2MS

Jerry, Thank you for the information! I have 2 v4s and a v5, all that the power "dips" on 40meters compared to 20.? By that, I mean that 80meters puts out 14watts, 40 about 9 watts, and 20 about

Mike, Yes, the boards are tested and calibrated at the factory.? With that being said, there have been some reports of the BFO not being optimized and fewer instances of calibration being off.? Both

They do get tested and calibrated, should just work. Some customers report issues with calibration, they find they must re-calibrate. Evan is currently investigating an issue with somewhat reduced

Evan, Older versions of the uBitx had plenty of power on 40m. Perhaps try reversing some of those changes between v4 to v5? The filter at L31,L32,C205 is needed to squelch the 90mhz harmonic of the

Justin, I’m doing the wending I use drills of 4 and 6mms to make the coils? 1,2 and 3. I have 3 questions: 1) In the picture? the coil L1 appears to have 4 turns, while noted 3. please confirm the

Hello, I am new to this group and just ordered a uBitX V6 full kit. The board seems to be fully assembled. Has the board been tested before shipping or have users found issues with this board that I

This is why I wish there were a way to edit the text after posting. The frequency that I tested at was NOT 3.55 MHz, rather it was 10.100 MHz.? The 3.550 MHz TP12 was also around 30mVpp and produced

Interesting, I may have the same issue,? On 40M I have 12W out on SSB (according to the wattmeter in the ATU) but CW is just under 4W.? I also have about 6.2W out SSB on 20M, haven't checked the

Yes, the PIC and all SMD parts were pre-installed.

All, I got around to assembling my v6.? I have the same issue with this kit as others have mentioned in this thread and others.? Namely, the 40meter power output is low.? I measure 5watts on 40 and

Justin, I totally agree that there is a STRONG need for an edit capability on this board.? When I go back and review my posts there are things I would like to change in 8 out of 10 times that I just

Jerry, FYI, the v6 now has a heatsink on the 7805 regulator.? I believe that was done because of the current requirements for the graphic screen.? You are correct for all of the other versions. 73

Mike, With that regulator and a proper heatsink, you should be able to run all of the 5volt circuits from a single device.? You could just replace the 7805 on the Raduino with that one and be good to