开云体育

Hi Steve, If you use the MP-Lab-X software, and attempt to program something in a different family that last used, then it usually re-flashes the bootloader and firmware. Roger.

Many thanks both of you for your help. I uninstalled 3.1 from my laptop and from my PC and reinstalled. It could not find my Pickit3 on either machines. I installed MP-Lab on my Apple iMac and on my

hi Steve, search for my post # 1994 from 24.01.23 I‘ve appended picKit 3 software for Win 10 Immo

Hi Steve, MP-Lab-X IDE/IPE works with the PICKit3. 5.x runs on Windows 10 (and includes mpasm) 6.x Runs on Windows 10/11 (but does not includes mpasm) Roger.

Can someone please send me a LINK? to the latest application software that'll work on Windows 10 for the Pickit 3. I used my Pickit 3, 3 or 4 years ago with 3.1 software on an old laptop and I was

Many thanks for that Karl. I have done it before when I fitted an ATU-100 in the feed box on my Cobweb Aerial. I have a Pickit but forgotten how I did it! I touched the B1 pin to ground and it is

Steve, you can reprogram the EEPROM section of the ATU and write the value 01 into location 02 and that will permanently put the device into auto mode - assuming you don’t have any buttons to

I want to setup my ATU-100 in a waterproof box at the base of my 111ft (34mtrs) Inverted "L" Long Wire. I gather that if I momentarily ground RB1 just once to will push it into Automatic mode and

If this is "simply" a beefed up version of the ATU100 then the programming port is shared by the display connector.? This needs a pickit3 and is covered elsewhere on this forum.

Hi Derek, Try swapping the input and output coax leads over, as some boards have these labelled the wrong way around. Otherwise, try more power, as the 1000W version needs a bit more (unless you tweak

I've been using an external, stand alone , no remote control, version of ATU100 (AT150 , modified ) for 2 years. No problem at all regarding the display. I just need it for maintenance and som

ATU1000 requires more than 10W tuning power. Set in the transceiver at least 30W... up to 50W even. A lot depends on how the tuner was configured! --- Cu ganduri bune, Marius - YO6RK senty.ro 73!

Hello Mike! Yes. You can use it without the LCD. 73 DE PP5OO

Sure is something was screwed up with software, nothing neither display would work. So take care about the swr/ power sensor. 100% you made a mistake or bad manufacturing.

Hi, I have purchased a 1000 Watt version from Ali Express of this ATU, went to try it out a few days ago and connected it all up, power on and had display of SWR and Power on the display unit, unit

Its been a while since I owned an ATU100 and Im thinking of getting another for remote tuning of a Doublet. I dont remember if a lack of display causes the software to hang-up or if its possible to

Roger, Yes the 8302 prices from Mouser etc have inflated quite a bit lately. The prebuilt $10 modules? from the usual suspects are around one third the price for whatever reason. ? I have one of

So - finally I've got some time and tried the new David's code on one of my ATU-100 units. What can I say - the tuning speed was dramatically low and device was more or less unusable and unstable

Hi Ian, The SGC and some Icom tuners seem to use (expensive) phase detection chips to measure phase and impedance. Some of the MFJ and mAT, plus the ICOM AH-4 seem to use a series resistor switched

Hi Ron, The EEPROM L and C values are only used for the display, they aren't used for any calculations during tuning. Roger