开云体育

Good Morning, I'm testing a WX3in1 running as an APRS I-Gate W3TAC-1 with digipeater-off. Everything appears to work on the TCPIP/internet/APRS.FI side. My half wave antenna is only 18 inches off the ground so I don't expect to get out (10 watts) very well on xmit but it works well enough for testing. The status box on upper left side of APRSIS32 flashes between "APRIS-OK" and "WX3in1 KISS-OK" but about every 6 seconds something quickly flashes so fast in the background I can't read it but I think it says something like WX3in1 KISS OPN CMD? With the scroller set to RF only no stations show up in the left column but plenty of APRS-IS stations show up on the map from the internet side. The WX3in1 is in the basement feeding the router upstairs via Cat-5 cable. Been working this for weeks and starting to think the WX3in1 is not compatible with APRSIS32. Anybody get their WX3in1 working with APRSIS32? Tony

New to aprs and trying to setup my FTM-500 in my house as an I-gate With aprisce32. I can't seem to get RF received on my station to forward to APRS-IS, at least, I can't see any traffic showing up in my area on APRS-FI. I am receiving traffic and it shows in APRSIS on my computer. I can see my mobile KQ4LMY-9, beaconing in my driveway, but it doesn't show on an online map. My home station shows on aprs-fi, but it is being seen by a digi-peater 35mi away to the NE or another 33 miles to the SW. FTM-500 is connected to computer via Yaesu SCU-56 cable. Made FTM-500 port using FTM-350 setting. Internet is provided via starlink. Log files are attached. Any help would be appreciated. Thanks, Brent KQ4LMY

Good morning! I've been trying to figure out how to make it so it doesn't beacon so often. I went to configure and smart beaconing and set the times roughly to every 3 hours, but I see it's still beaconing pretty frequently. I'm not on the 390 as I'm doing some other testing but I'd rather it not beacon so often. Thanks!

Probably not for this group, but you never know. I use a developer version of the prog to fill in Mold with local internet activity. Just got an update installed. It's working great, and I like the tracking windows and stuff. It's on MB7UMD-10 and it's driving me nuts. Once every 24/72 hours the usb port disconnects from the serial converter. I assume this is the case as the radio decides it's no longer in KISS mode and I fix the issue by removing and replacing the USB A connector on the PC. Just in case I changed the USB/Serial converter and that installed new prolific drivers to a new com port but didn't fix the problem. I'm guessing it's windows 10 The machine is an old Fujitsu and it's working very hard to run win10 to be fair. Anything I can look at?

I need help setting up my KPC3+. I replaced my TNC that died with another newer KPC3+, I lost all my programming and internal setup. Is there any out the to assist? Matthew KK4ZDZ

Can the software be configured to auto restart after and power failure or windows update?

Hi, Is there a release note file for the latest development version dated 5 September 2024? If yes where can we find it? I checked but I couldn't find anything at the Wikidot. Any link would be of great help. -- 73 de Demetre - SV1UY

When I open first APRSISS32 I keep getting a message at the bottom of the page that says " Beaconing Suspended. Confirm Center and Transmit". How do I do that?

For some reason I'm not coming up with an answer after grazing the usual sources... How does one configure APRSIS32 to send telemetry from an external source? I've got a solar / battery system in the Shack with an Arduino that reads info from the Victron charge controller, driving a small LCD display. It occurs to me that it should be easy to pipe that data via a serial connection to the PC. It's already set up to output the data from my weather station (via WeeWx to the WxNow.txt file). How does one get similar data into the Telemetry feed of APRSIS? Looking at http://aprsisce.wikidot.com/doc:telemetry I see that there are configuration packets that need to be sent for the IS to know how to format the data, but I don't see how one configures APRSIS32 to read and send the actual data. The "Telemetry" box is checked on the General configuration, yes, but where does it fetch the data from? I'm missing a key piece to the puzzle. Unusually baffled on this, Greg KO6TH

With the new Development version, I have noticed a peculiar problem. When I receive a NWS warning object over IS, APRSIS32 commands the D710 to transmit the respective messages as follows: K4VBX>APK102,WIDE1-1,WIDE2-1::AKQFFS :rej0 K4VBX>APK102,WIDE1-1,WIDE2-1::AKQSMW :rej0 I have restarted the program without activating the IGate, and it still does this. I have tried disabling messages in the IS port and the RF port, but this makes no difference. I do not see the packets in the Igate Test Filter. Strangely they are not in the Transmit log either. However, the TOCALL tells me something is commanding the D710 to create the packet, and I am connected to the D710 in APRS mode. To be sure, I disabled all digipeat options on my D710. Running several logs actively to try to narrow this down. Any thoughts?

what is the best way to NOT show nws flood warnings/statements but show all other NWS warnings?

I am still trying to find the ins and outs of the program. Is there a way to actually monitor RF and decode packets in real time? I am running a KPC3 (not plus) in KISS mode.

I would like to use digipeater using two ports vara and kiss. How would I have to configure the xml file so that rf 2m traffic goes out to rf 10m vara and vice versa? Enviado con Mailsuite · Darse de baja 26/06/24, 12:42:24

I enabled frequency monitor on the stabile 2020 version of APRSIS32 and can't turn it off!! Advise needed, please help. Hank/ke0cu