开云体育

IIRC, the original FTM-350 manual actually had a section describing hooking up an external TNC via audio in order to enable transmitting packet or APRS.?? Does the FTM-100 manual have that section?

Yes i can receive packets on the radio and to APRSISCE via radio speaker output to computer mike input. I would like to use it as digipeater but i am beginning to think it is not possible. Maybe a TNC

I think I saw on the yaesu group at one point that they don't have real tncs inside which is why they are not accessible. If the 100 is like the 400 it should have a data port where you can attach an

Check your user manual. Can this device accept incoming data? The original Yaesu radios would only output data to an attached computer and could not accept data from a computer for transmission. Not

Can i use the above radio as a digipeater with APRSISCE? If so what cables would i need to connect the radio so it could activate the transmitter for a digipeater.? Would a boafeng be easier? than

Its just the way I am typing it out. I am, in most cases, using programing software (RT Systems) which sets the SSID up. I just select from a Drop down menu. Brian

Lynn I sent you my Configuration file as that may be the easiest way for you to figure this out. I am sure I crossed a T or Dotted an I that I should not have done.? Again, thank you for your help in

Is there a reason you are using a nonstandard callsign and SSID format?W4BJB/7 vs W4BJB-7? Robert Giuliano KB8RCO

If he is using the non-paid version of the aprs.fi app, it does NOT do true APRS, but simply puts location information onto the aprs.fi web site.?? If you try looking at the raw packets for his

I use SARTrack and have a similar problem with a friend of mine. He uses an Apple Phone and not sure which APRS app is used on Apple phones. All I know he shows up on .fi but not on my APRS map and my

There are LOTS of moving parts behind what shows up on your local map.?? For instance: 1) Do you have an APRS-IS port configured and Enabled??? If you double-click the upper left (or top center)

I checked this morning and “View All” is checked. However W4BJB and W4BJB/7 not showing but on APRS-FI. Strange

Yes I am 99% sure I do. Right now we have had some major thunderstorms and tornadoes go through my area so all radios and computers are shut down. I’ll double check to make sure in the morning

W4BJB13 (note the lack of a dash, any reason for that omission?) is on the CWOP network, not the APRS-IS network.?? You'll only get that in APRSIS32 if you add an additional port connected to a CWOP

Do you have View / All checked? Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

I got 3 APRS Devices that are showing up on APRS-FI but not on APRSISCE. ?I can’t figure out why? They are: W4BJB (Icom 5100), W4BJB/7 (Anytone 878 UVIII++) and W4BJB13 (Tempest Weather Station).

Hello Thanks for the info, I do have kiss protocol available in bpq32 however not sure if that is just the mode or of I need a kiss tnc. I have a digipeater igate configuration for bpq32 from my

OK I have some BPQ32 config information was sent to me. See I don't have knowledge if I need special equipment to run kiss as in a separate tnc or if I'm just running in kiss mode. Yes bpq has the

It's been years since I ran BPQ. You need to modify your BPQ32.cfg file as John Wiseman has info about running APRS. 73 *Don PoapsNew Westminster, BC*VA7DGP DATA VA7QU VOICE *Winlink:

I'm not familiar with bpq32, but if it offers a KISS-over-TCP port, the connection would be trivial.? But before we dive into that, I'll see if anyone has actually made the connection already between