开云体育

There are LOTS of moving parts behind what shows up on your local map.?? For instance: 1) Do you have an APRS-IS port configured and Enabled??? If you double-click the upper left (or top center)

I checked this morning and “View All” is checked. However W4BJB and W4BJB/7 not showing but on APRS-FI. Strange

Yes I am 99% sure I do. Right now we have had some major thunderstorms and tornadoes go through my area so all radios and computers are shut down. I’ll double check to make sure in the morning

W4BJB13 (note the lack of a dash, any reason for that omission?) is on the CWOP network, not the APRS-IS network.?? You'll only get that in APRSIS32 if you add an additional port connected to a CWOP

Do you have View / All checked? Lynn (D) - KJ4ERJ - Author of APRSISCE for Windows Mobile and Win32

I got 3 APRS Devices that are showing up on APRS-FI but not on APRSISCE. ?I can’t figure out why? They are: W4BJB (Icom 5100), W4BJB/7 (Anytone 878 UVIII++) and W4BJB13 (Tempest Weather Station).

Hello Thanks for the info, I do have kiss protocol available in bpq32 however not sure if that is just the mode or of I need a kiss tnc. I have a digipeater igate configuration for bpq32 from my

OK I have some BPQ32 config information was sent to me. See I don't have knowledge if I need special equipment to run kiss as in a separate tnc or if I'm just running in kiss mode. Yes bpq has the

It's been years since I ran BPQ. You need to modify your BPQ32.cfg file as John Wiseman has info about running APRS. 73 *Don PoapsNew Westminster, BC*VA7DGP DATA VA7QU VOICE *Winlink:

I'm not familiar with bpq32, but if it offers a KISS-over-TCP port, the connection would be trivial.? But before we dive into that, I'll see if anyone has actually made the connection already between

Hello I have an instance of bpq32 and winlink rms running on my computer with a radio and signalink. Been running very well for nearly 1year. I have aprs running in bpq32 shows up as BBS. I have

Keep in mind that the quoted values are "when a packet signal is present", not just open squelch noise. Also, a high RXAMP is as bad or worse than a low on. I have tried 2 methods for setting RX amp:

Wooo Hooo!? It's now seemingly working as it has been.? I had my receive amp on the Tiny Traker 4 at 47.? Sure I hadn't changed anything but it wasn't receiving what it should have been so I turned

The Time in the upper left corner is actually the Transmit Pressure.?? You can read about it at: http://aprsisce.wikidot.com/doc:screen-features The thin colored bars at the bottom of that pane are

Yes, the upper left corner shows the time until your next beacon. Lynn was answering the other portion, but I didn't see a response to that part of your post. ------- Robert Giuliano KB8RCO

Ok, I just double-checked the source and the timestamp in the ?APRSS response is actually the timestamp that the port entered the current state.?? I now remember doing this so that you can see if

Send yourself a ?aprss and see what time is shown in that response.?? I just did it and it shows 04-30 07:52:19 and my local time is 10:45:xx, so not even the minutes is correct.?? Unless, of

The times do not seem to match my PC system clock time which is accurate from a utility which keeps it synced to an accurate time source.

See the screen print.? Can anyone tell me where the time in the upper left-hand corner comes from?? It appears to be counting down.? Is that the time to the next beacon transmission? How about the

Yep, you are correct, only TX pot. I was working from memory. And your procedure is much the same as mine. Ben Miller, PE retired KD9BBB 708-431-7875 bmilleng@... [email protected]> wrote: