开云体育

It's a JA or EU? market control board. You can use it, but you'll need to reprogram it with the NA TX partition table, then do your hardware mods. Jim WA9Z

Hi group, I have a problem trying to expand the bands on one 920 rig which had its mainboard replaced but I can't do it. First of all, the mainboard doesn't have the green cable that should be cut

I had to do a master reset on my FT-920. I don't remember what the setting for menus U45 and U46. Been several years since I set the radio up. I set U45 to 0 and U46 to 1700 Hz. That is from my notes

> > Hello what is the best PC management software for the yaesu ft-920 ? > > hamradio deluxe aside... e.g. ftdxrc or similar...

Hi, I have a problem with my tuner, the motors work perfectly but on the 12 and 17 meter bands and occasionally on the 10 meters the tuner doesn't work correctly, I've done all the resets but it

Hi just bought a near mint FT920 from a local for ?50 gbp. of course it'#s faulty. so lights up, good sign.. no TX, RX is good using a signal generator but no sound.. speak 'clicks' on switch on and

I have a mint FT 920 for sale. I am the original owner and non-smoker.? Has the custom cover--always kept covered. No mods, scratches or blemishes. For sale $725 firm. I am in Gettysburg but can

Hi all, I'm setting up a FT-920 for FT8 and data signals etc, but just wondering if the 5 pin DIN plug is it a standard DIN plug or mini DIN plug? Thanks Robbie ZL3OBI

Right sorted out the the playback issue on the DVR, it was just me holding the play button in to long, sending it into monitor mode not play mode

Hi to all I have just purchased a FT 920, After recording the 4 messages on the DVR it plays back and is audible, but does not go into transmit mode, Also antenna B is like their is no antenna plugged

Thanks Gene, please can you tell me how to do to clean it or if there is any tutorial on the net? Thanks 73 de Enzo IK8OZV EasyLog 5 BetaTester EasyLog PDA BetaTester WinBollet BetaTester D.C.I.

Sorry I didn't read it correctly sounds like it has a dirty tuning pot I actually have a complete 920 for parts it has a bad main board I am fixing to list all the parts GENE MITCHELL. Kc0mqg

Gene, thanks for your reply but you did not answer about my issue. Please read careful Thanks 73 de Enzo IK8OZV EasyLog 5 BetaTester EasyLog PDA BetaTester WinBollet BetaTester D.C.I.

If you turn it all the way either way it will tune rapidly if you turn it slightly it will tune slower hope this helps this is what mine does anyway GENE MITCHELL. Kc0mqg

Hello to All, HNY to everyone. Please I have an issues with my Yaesu FT-920. If I try to decrease the VFO using the Shuttle Jog ( I mean the inner VFO knob ), the frequency instead to Decrease it

Hi all, im wanting to know if it's possible to use my ham antenna as a sdr receive antenna and also if i can connect the same antenna to my yaesu frg7 Am i right in thinking that there is no antenna

Hi I am trying to use the external output for speaker (rear) to pass the output signal through an AUTEK QF-1 Audio Filter and then split the output signal either to an external speaker or a

Well the hunt is over.? After numerous returns to scour the board for Q2037 I found it.? It is located right in front of the rear key jack and the Pdl-Key switch.? Looks like it is a through board

I was going to use the 13.5V output (J2001) from the back of the 920 to power an Ameritron ARB-704 amplifier/radio interface.? I have no power at jack J2001.? The Op manual says the connection is

My FTdx-3000 has the blinking transmit light issue.? I have factory reset the radio several times, left it unplugged for days, disconnected everything to insure some external source was not keying