|
Hi Oleg, Yes it is a shame that FM is not good, I did have a g90 and when they added FM to it, RX was ok, but FM tx audio was not great, With the 6100 tx audio is better than the Rx audio, Good luck Dave 2E0DMB
On Sun, Dec 10, 2023 at 01:52 AM, davebb123456 wrote:
Has your Transverter arrived yet? ?
?
Yes, it has arrived. I only tested it for reception, I did not try it for transmission. I plan to do this one of these days. Now I'm stubbornly trying to overcome the problem of loss of sound playback. So far no success.
?
But it is already clear that FM is received disgustingly. I once tried to transmit on FM in the CB band, and it was also very bad. It seems that the manufacturer did not check this modulation at all.
I can’t fix it, because it’s all in the closed BB firmware of the processor.
|
On Sun, Dec 10, 2023 at 01:52 AM, davebb123456 wrote:
Has your Transverter arrived yet? ?
?
Yes, it has arrived. I only tested it for reception, I did not try it for transmission. I plan to do this one of these days. Now I'm stubbornly trying to overcome the problem of loss of sound playback. So far no success.
?
But it is already clear that FM is received disgustingly. I once tried to transmit on FM in the CB band, and it was also very bad. It seems that the manufacturer did not check this modulation at all.
I can’t fix it, because it’s all in the closed BB firmware of the processor.
|
Hi Oleg, Thanks for the info I will try a smaller card,? Has your Transverter arrived yet? ? Thanks Dave?
On Sat, Dec 9, 2023 at 10:36 PM, davebb123456 wrote:
can you please tell me if running your firmware on a smaller SD card
Yes, the size of the SD card is limited only by the size of the image. Now the image is 1GB, so you can orientation on it size as minimal.
|
On Sat, Dec 9, 2023 at 10:36 PM, davebb123456 wrote:
can you please tell me if running your firmware on a smaller SD card
Yes, the size of the SD card is limited only by the size of the image. Now the image is 1GB, so you can orientation on it size as minimal.
|
Hi Oleg
can you please tell me if running your firmware on a smaller SD card will make it run any better as i am using a 128Gb card and it is running fine
Thanks Dave 2E0DMB
|
I use the GPS dongle and it works well with the R1CBU version 0.19.0 to set time and location. The only problem, which is not a problem for me, is the presence of the USB device disables the screen keyboard. Version 0.19.0 sees the usb port is being used and acts as if an external keyboard is plugged in.
Enjoy Life, Greg
Live Well, Laugh Often, Love Much
toggle quoted message
Show quoted text
On 12/8/2023 16:56, VA3NCA Wayde via groups.io wrote:
> Isn't anyone using the GPS function that Oleg
> incorporated to set the time?
I am. I'm using a cheap usb dongle from Amazon. It works great!
Wayde Nie VA3NCA
73
|
> Isn't anyone using the GPS function that Oleg > incorporated to set the time?
I am. I'm using a cheap usb dongle from Amazon. It works great!
|
Isn't anyone using the GPS function that Oleg incorporated to set the time?
|
I use the website? time.is, link
?
I find now and again even though setting time by telling NTP to sync (it is windowz) if its within a minute it won’t update
?
Solution set time more than 5 minutes out, leave it a minute then tell it to set automatically and it will bring it back into sync
?
Peter
M0PWX
?
?
?
Update to decode issue:? Checking the time against the atomic clock and it was correct.? However, I went ahead and "set the time" and it cleared whatever the timing issue was.? I hooked up WSJT-X and Operated the default 20m FT8 and then
when I changed the Freq on WSJT-x, the radio didn't follow.? I manually change the band using the buttons to 10m.? ?FT8 decode and R!CBU V.19 Tracked correctly with WSJT-x so there is no problem.??
|
Update to decode issue:? Checking the time against the atomic clock and it was correct.? However, I went ahead and "set the time" and it cleared whatever the timing issue was.? I hooked up WSJT-X and Operated the default 20m FT8 and then when I changed the Freq on WSJT-x, the radio didn't follow.? I manually change the band using the buttons to 10m.? ?FT8 decode and R!CBU V.19 Tracked correctly with WSJT-x so there is no problem.??
|
On Thu, Dec 7, 2023 at 08:49 PM, Chuck Maslin wrote:
Any idea why the FT8 wouldn't decode anymore??
One of the reasons is that the time on the device is not correct
|
Any idea why the FT8 wouldn't decode anymore?? ?Any parameters that should be set to get it going again?
|
On Thu, Dec 7, 2023 at 08:10 PM, Chuck Maslin wrote:
It wouldn't decode the 20m FT8 anymore, nor could I move
the frequency with the direct microphone input, either by pushing the band button or direct frequency entry.? The only way I could move the receiver off the 14.074 was to push the buttons on top
of the radio to change bands, it jumped to several digital frequency places for all the other bands.? ?I also noticed in the upper right corner that usb and not usbd was shown and I couldn't change the modes through lsb,lsbd,usb,usbd. It was stuck on usb only
Everything is as planned. I talk about this in the video announcement of this version (subtitles with translation are automatically available). Now the FT8/FT4 frequencies are recorded and you can only navigate through them using the band switching buttons. It is also prohibited to change the modulation mode.
|
Oleg,
First I want to thank you for your programming.? I really like what you've done and what you are doing.
Thank you for addressing the audio feedback issue I posted earlier.
I found another issue with v.19. This one is around the FT8 decoding.? when I first ran the new firmware it worked really well.? However I noticed a few things yesterday that I can't figure out.
When tuning to 10m for ft8 yesterday, I pushed app button then FT8 and the receiver automatically jumped to 14.074 (20m).? It wouldn't decode the 20m FT8 anymore, nor could I move
the frequency with the direct microphone input, either by pushing the band button or direct frequency entry.? The only way I could move the receiver off the 14.074 was to push the buttons on top
of the radio to change bands, it jumped to several digital frequency places for all the other bands.? ?I also noticed in the upper right corner that usb and not usbd was shown and I couldn't change the modes through lsb,lsbd,usb,usbd. It was stuck on usb only.? All the timeslots didn't decode on any of the other bands that I ran through.??
Thank you again for all the work you do.? ?I appreciate it greatly.
kd6aej
|
On Wed, Nov 29, 2023 at 05:52 AM, <email.jjb@...> wrote:
but is there a "Restore Default" function in your firmware like there is in the standard GUI Settings menus?
There is no such function yet. To reset all settings, just overwrite the params.db file on the SD card in the DATA section.
|
Hi Oleg,?
I have been using r19 for a couple of days, my first experience with your firmware.? Really awesome work, thank you for your efforts.?
I feel like I am missing an obvious function, but is there a "Restore Default" function in your firmware like there is in the standard GUI Settings menus?? To reset to default TX Power, Mic gain, etc. and the little "chasing arrows" circle found in the lower left of the standard GUI?
Thanks,?
Jim, KB8JJB
|
My translator works in Youtube, have to
turn on translate, then turn on Close Caption/subtiltles
Lou W0TQ
On 11/28/2023 06:14, Ron Liekens wrote:
toggle quoted message
Show quoted text
Oleg, I see this as an extra feature besides the automatic
speed function. The way it works now is that with slow morse
speed the software is always seeking for dots and dashes in the
time between the send characters.
Another possible solution is the function to 'lock' the receive
speed and later unlock it if you want. It is a bit fiddly, but
it can help in a way.
?
Strange that you see this as a 'bad' idea?
Yes, Bluetooth audio is what I'm looking for.
Could it be possible to activate the YouTube text translation
option to English. I see you explaining many things, but the
Russian text is not helping, LOL.
73' Ron
|
Would be nice to lock the receive speed. I see what you can offer us in the future.
Must be an Android- YouTube thing. I will check another OS to see what is happening with the auto-translation.
Thanks for taking an interest.
73' Ron
|
On Tue, Nov 28, 2023 at 03:14 PM, Ron Liekens wrote:
Another possible solution is the function to 'lock' the receive speed and later unlock it if you want. It is a bit fiddly, but it can help in a way.
I can't promise anything yet, but I'll think about what can be done.
Could it be possible to activate the YouTube text translation option to English. I see you explaining many things, but the Russian text is not helping, LOL.
This is quite strange, because I turn on auto-translation subtitles and everything works for me.
|
Oleg, I see this as an extra feature besides the automatic speed function. The way it works now is that with slow morse speed the software is always seeking for dots and dashes in the time between the send characters.
Another possible solution is the function to 'lock' the receive speed and later unlock it if you want. It is a bit fiddly, but it can help in a way.
?
Strange that you see this as a 'bad' idea?
Yes, Bluetooth audio is what I'm looking for.
Could it be possible to activate the YouTube text translation option to English. I see you explaining many things, but the Russian text is not helping, LOL.
73' Ron
|
Wayde VA3NCA/AD2GX
Peter M0PWX