开云体育

I have opened an ISSUE #118 that describes the problem I see with the DNF. The settings are flipped for freq and width. Could it be my old param db causing confusion? Happy to try suggestions to

It is based on the latest version of buildroot (2024.11.1), and has a few other changes described here: /g/xiegu-x6100/message/6527 The two versions should behave almost identically

When you see someone post that they “ built the firmware based on latest buildroot (2024.11.1),” it means that this version works with the LATEST version of the radio that came from the factory

Excuse my ignorance but how does this compiled version differ from the v0.29.1 ( https://github.com/gdyuldin/x6100_gui/releases/tag/v0.29.1 ) release ?

Thanks Georgy for the latest version of your firmware! Last night I built the firmware based on latest buildroot (2024.11.1) using your version 0.29.1; the SD card image is available here for those

Thanks, I'll check. Seems, I know the reason. Meanwhile - I fixed some issues and build a new release - 0.29.1 https://github.com/gdyuldin/x6100_gui/releases/tag/v0.29.1 -- Georgy // R2RFE

At last, i (think) got it. A/B-play/show mismatch ONLY starts ABOVE 18 MHz? Follow below steps exactly, but do not hurry, give radio time to execute cliks. 1. power off radio, remove params.db from

Swr scan leaving VFO in the wrong place: https://github.com/gdyuldin/x6100_gui/issues/105 -- John Flinchbaugh john@... [email protected]> wrote:

I am unable to reproduce by following those steps, though I have noticed what seems to be similar behavior, but it was after adjusting the frequency encoder while in the SWR Scan app; once I exit the

Georgy - The sdcard_fixed_boot.zip fixed my reported issue - my X6100 is now able to successfully boot into v.0.29.0! Many thanks & 73 - Daniel/K4DB

Hmm. Can't reproduce. Maybe I press these buttons not so fast? Someone else can check this? -- Georgy // R2RFE

Can occur in different Band (DOWN/UP) and Vfo (A/B) combinations and A/B result can be opposite, but after EVERY these 8 clicks: A/B, BandUP, A/B, BandDOWN, A/B, BandUP, A/B, BandDOWN radio goes to

Yes, it's changed on the 0.29. The reason of "ghosts" was a spectral leakage. It was a bit annoying, when strong station hided weak one on waterfall/spectrum. -- Georgy // R2RFE

Well, I spend a day trying few newer versions of the buildroot (with helps of the Franco Venturi repo). Unfortunately, every time something doesn't work. Now I replaced uboot within 0.29.0 image from

Sent: Monday, February 17, 2025 9:25 PM To: [email protected] Subject: Re: [xiegu-x6100] Alternative FW v0.29.0 Hi Georgy, Thank you for new release! I’m testing your changes for a few days

Hi Georgy, Thank you for new release! I’m testing your changes for a few days with no issues so far. To me, 0.29 is a huge improvement! Not sure if it has been changed with 0.29, but I like the

Georgy - Any ideas when v.0.29.0 compiled with the newer buildroot version for the rest of us to test out? Thanks & 73 - Daniel/K4DB

Thanks a lot, Georgy, Great work - significant progress! -- 73! Anatoliy

Good idea Georgy, so atu table now shows in clear what was tuned. Opened params.db with SqliteBrowser to execute: *UPDATE atu SET freq=freq*50000+25000* and now ATU works like before.

I have also noticed that the internal CW generate by MSG menu keys is not uniform.? I can press a button with good CW and the next time I press it does not send the same characters.? Usually a dash