Re: Factory reset... not working
I didnt set a root password, but I am also not the first owner of this radio. They may have changed it.
?
I am flashing it with 1.1.4 now. We will see what happens when I update that.?
|
On Sat, Oct 5, 2024 at 10:55 PM, p p wrote:
Is it possible to disable the display.
I hear many people complain about low battery life.
?
Turning off the display has almost no effect on power consumption. Much more significant if BT/WiFi is disabled
|
Re: Factory reset... not working
" root, and password:123 will not allow me to login. Says denied."
I would bet that Factory Reset doesn't change/restore the user
passwords... Did you previously (intentionally) change the root
password? Maybe try that--
73, Paul -- AI7JR
--
Paul -- AI7JR
|
It happened to me too, but it got hot first and showed to be transmitting at 24 watts!? Luckily mine was under warranty and Radioddity sent a replacement
I know this is an old thread, but I am facing the same issues, no output power after first try for FT8.
I managed to made the first and only QSO, but then no transmission.
Afterwards, no output power in any mode with internal and handle microphone,
?
Everything is properly set in radio (or also in software for FT8, where there I have tx, click sound, tuning, tx etx properly working) but without any output power).
I have tried so far 1.1.6, 1.1.7 (the firmware that the radio came with from a SK, and the latest of September 2024). Any ideas/solutions software related? I am afraid that probably something is broken inside the transceiver. Many thanks in advance for any help.
|
Try short push of power button?
Is it possible to disable the display.
I hear many people complain about low battery life.
However a display is only really mandatory for initial tuning after that its less useful
Especially for digi modes where you tend to lock to a single frequency
|
Is it possible to disable the display.
I hear many people complain about low battery life.
However a display is only really mandatory for initial tuning after that its less useful
Especially for digi modes where you tend to lock to a single frequency
|
Re: Factory reset... not working
If you changed the root password on the system - you have 2 variants. First - flash an old xiegu firmware. Old versions rewrite all files on the system and should reset the root password. Second - boot from SD card (using R1CBU firmware, for example), mount internal storage and remove the root password hash in the /etc/shadows ()
Problem I have, is that even after doing a factory reset, using userid: root, and password:123 will not allow me to login. Says denied.
|
Re: Standard FW CW decode?
toggle quoted message
Show quoted text
From: Richard (K3RWN) via groups.io
Sent: Saturday, October 5, 2024 5:26 PM
Subject: Re: [xiegu-x6100] Standard FW CW decode?
?
Thanks,
?
Thankfully we have .25!
Rich
|
Re: Standard FW CW decode?
Thanks,?
?
Thankfully we have .25!
Rich
|
Re: Standard FW CW decode?
The XIEGU FW CW decoder always works poorly. The decoder has no AFC and no automatic signal threshold. A decoder like that can never work well. Stupid programming... unfortunately. 73/6 Jens / HB9JOI +++ -----Ursprüngliche Nachricht----- From: Richard (K3RWN) via groups.io Sent: Saturday, October 5, 2024 4:53 PM To: [email protected]Subject: [xiegu-x6100] Standard FW CW decode? Has anyone had any luck in getting the CW decoder (send or receive) to work in the Xiegu FW? Is there a trick or setting that I am missing? It works great in .25 third party FW. Just curious. Rich
|
Has anyone had any luck in getting the CW decoder (send or receive) to work in the Xiegu FW?
Is there a trick or setting that I am missing?
It works great in .25 third party FW.
Just curious.
Rich
|
Re: Factory reset... not working
Problem I have, is that even after doing a factory reset, using userid: root, and password:123 will not allow me to login. Says denied.
|
I had the same problem with WSJT on older firmware (117/116?).? Interestingly, MSHV worked perfectly.? With the latest firmware downloaded from Radioddity (1.1.9/1.1.8) both programs work perfectly for me. ?
toggle quoted message
Show quoted text
From: [email protected] <[email protected]> On Behalf Of skywalker_orion_greece via groups.io
Sent: Thursday, October 3, 2024 5:54 PM
To: [email protected]
Subject: Re: [xiegu-x6100] No power output? I know this is an old thread, but I am facing the same issues, no output power after first try for FT8. I managed to made the first and only QSO, but then no transmission.
Afterwards, no output power in any mode with internal and handle microphone,
Everything is properly set in radio (or also in software for FT8, where there I have tx, click sound, tuning, tx etx properly working) but without any output power).
I have tried so far 1.1.6, 1.1.7 (the firmware that the radio came with from a SK, and the latest of September 2024). Any ideas/solutions software related? I am afraid that probably something is broken inside the transceiver. Many thanks in advance for any help.
|
Re: Factory reset... not working
On Thu, Oct 3, 2024 at 11:19 PM, John Brent - VA3HQB wrote:
and all my WIFI settings and password settings are still there...
They are stored in your radio OS at /etc/NetworkManager/system-connections
You're better off folowing the previous advice (via USB) or creating a new working wifi connection and then go in the radio and delete the connections that you don't want to keep.
73.
?
Joao, CT2HME
|
Re: R1CBU firmware 0.25.0
LATE EDIT... About 30 seconds after posting this, I found the answer to my question — right in front of my eyes. So I no longer need an answer to this.
?
Quick question... and maybe a dumb one, so I'll ask forgiveness in advance... How do I turn off voice monitoring? In other words, when I key the mic, I hear my voice through the speaker — with howling feedback unless I turn the volume down quickly. I've searched through all the menus, but I'm clearly blind to something obvious that I can't seem to locate. Any help would be appreciated.
73, Randy K7RAN
?
|
Re: Factory reset... not working
As far as I remember, WiFi settings are not stored in the xparams.db (this table contains radio parameters), but within OS.
You can connect radio with usb cable using PuTTY (or screen under linux) and manage connections using nmcli command.
E.g.
List all saved connections - nmcli connection
Remove connection -? nmcli connection delete "NAME"
Instead of name you can copy and paste UUID (long sequence from 2nd columns, looks like 'b9d1df81-8b58-4e63-a67d-330527f8e022')
?
|
Factory reset... not working
Good evening,
?
I have been trying to connect to my X6100 via SSH, but I want a fresh clean install.?
?
When I "Factory Reset" it warns me twice, then turns off. I wait a few min 5-10, I restart it... and all my WIFI settings and password settings are still there...
?
What am I doing wrong?
?
John Brent
|
Re: R1CBU firmware 0.25.0
That took care of the issue - many thanks!
Daniel /K4DB
toggle quoted message
Show quoted text
This is a Windows issue.? Put the card back into your PC.? Right click on Windows and go to Disk Managment.? Find the drive with the Boot partition and you will see another active partition with no drive letter.? Right click on that partition and Add drive
letter.? Now you will see the Data partition.
?
This e-mail and any files transmitted with it are the property of Arthrex, Inc. and/or its affiliates, are confidential, and are intended solely for the use of the individual or entity to whom this e-mail is addressed. If you are not one of the named recipient(s)
or otherwise have reason to believe that you have received this message in error, please notify the sender at 239-643-5553 and delete this message immediately from your computer. Any other use, retention, dissemination forwarding, printing or copying of this
e-mail is strictly prohibited. Please note that any views or opinions presented in this email are solely those of the author and do not necessarily represent those of the company. Finally, while Arthrex uses virus protection, the recipient should check this
email and any attachments for the presence of viruses. The company accepts no liability for any damage caused by any virus transmitted by this email.
|
Re: R1CBU firmware 0.25.0
This is a Windows issue.? Put the card back into your PC.? Right click on Windows and go to Disk Managment.? Find the drive with the Boot partition and you will see another active partition with no drive letter.? Right click on that partition and Add drive letter.? Now you will see the Data partition.
?
|
Re: R1CBU firmware 0.25.0
Just formatted the card with .25 using Rufus - put it in the X6100 and let it boot up - looks good. However, after having previously saved the files in the /DATA partition - I went to restore them after the initial bootup with version .25. Once I put the card in my laptop card reader, I could not find the /DATA partition at all - just the /BOOT. I placed the card back in the X6100 and powered it up again. Entered and saved a few basic data fields - "QTH", "Callsign". Power-cycled the radio - it did keep all the preferences that I'd just keyed in - however, no /DATA partition visible in Windows 11 File Explorer.
?
Took the radio out at lunch and tried it - worked wonderfully - the best in the 2 years that I've owned the X6100!. Made several FT4 contacts - noticed that the app worked much better than previous versions - each contact returned a "QSO Saved" message on the screen as normal. Get back to work after lunch, mount the card and still no /DATA partition! What am I doing wrong here?? Thanks!
?
Daniel/K4DB
|
John Brent - VA3HQB
Paul - AI7JR
Jens/HB9JOI
Randy K7RAN