Re: v0.25.1 displaying as v0.25.0 ???
The only difference between 0.25.1 and 0.25.0 is that voice prompts is fixed in 0.25.1. I forgot to bump version, while creating 0.25.1 build.
Georgy // R2RFE
|
v0.25.1 displaying as v0.25.0 ???
?
I have downloaded and installed v0.25.1 from GitHub. As the x6100 boots it briefly displays the firmware as being v0.25.0 not v0.25.1? I am a little confused. Have I installed the latest firmware?
?
John. 2E0JJC
|
X6100 have a weak output transformer - I heard about a case, when using FT8 with high output power burnt it out (with a condenser) - (it's on Russian, but you can use auto translated cc).
Another variant - if you used ATU - you can try to switch to any DIGI mode and press PTT for a second.
73, Georgy // R2RFE
|
On Mon, Oct 7, 2024 at 08:11 PM, SA5QED/David wrote:
When GPS is connected and has acquired a position fix, it would be nice to have the QTH automatically populated with the current Maidenhead locator.
I created an issue - 73
|
Re: Patched BASE firmware with changed TX audio filter low cutoff frequency
#firmware
Thanks Franko.
I created a bit more strict script for patching, while I apply changes to 1.1.8. It checks md5 of source before patching, uses predefined offsets for changes and checks, that content on each chunk is equal to expected original value.
|
Re: Patched BASE firmware with changed TX audio filter low cutoff frequency
#firmware
Thanks Georgy.
?
Based on your patches to Xiegu BASE firmware, tonight I wrote a simple Python script (attached) that should apply the corresponding changes to future (or older) Xiegu BB firmwares (unless they change their code significantly, of course).
?
The script can be run as follows:
./patch-160Hz.py <original decrypted BASE firmware> <patched decrypted BASE firmware>
?
Franco
|
When GPS is connected and has acquired a position fix, it would be nice to have the QTH automatically populated with the current Maidenhead locator.
?
73 de SA5QED/David
|
Re: TX not working under CAT / digital modes
Sorry to hear.? Could an R1CBU 0.25.0 user report on your experience with this issue?? Did you experience FT8 TX issues that R1CBU 0.25 resolved?? Thanks for your input, and thanks to the developers of this firmware!? (I look forward to trying it). ? Tony KE1TLG ?
toggle quoted message
Show quoted text
From: [email protected] <[email protected]> On Behalf Of skywalker_orion_greece via groups.io
Sent: Sunday, October 6, 2024 5:36 PM
To: [email protected]
Subject: Re: [xiegu-x6100] No power output? unfortunately none of the upgrades worked for me. I do not if I will be able to find the receipt from the relatives of the SK to check if the warranty is still valid and then I could give it a try. Its too sad to have the transceiver broken only by trying to work it via CAT.? Many thanks for your replies, I will keep you updated for any changes.
|
Dear Tony and John,
unfortunately none of the upgrades worked for me. I do not if I will be able to find the receipt from the relatives of the SK to check if the warranty is still valid and then I could give it a try.
?
Its too sad to have the transceiver broken only by trying to work it via CAT.?
?
Many thanks for your replies, I will keep you updated for any changes.
?
?
|
Re: Factory reset... not working
I didnt set a root password, but I am also not the first owner of this radio. They may have changed it.
?
I am flashing it with 1.1.4 now. We will see what happens when I update that.?
|
On Sat, Oct 5, 2024 at 10:55 PM, p p wrote:
Is it possible to disable the display.
I hear many people complain about low battery life.
?
Turning off the display has almost no effect on power consumption. Much more significant if BT/WiFi is disabled
|
Re: Factory reset... not working
" root, and password:123 will not allow me to login. Says denied."
I would bet that Factory Reset doesn't change/restore the user
passwords... Did you previously (intentionally) change the root
password? Maybe try that--
73, Paul -- AI7JR
--
Paul -- AI7JR
|
It happened to me too, but it got hot first and showed to be transmitting at 24 watts!? Luckily mine was under warranty and Radioddity sent a replacement
I know this is an old thread, but I am facing the same issues, no output power after first try for FT8.
I managed to made the first and only QSO, but then no transmission.
Afterwards, no output power in any mode with internal and handle microphone,
?
Everything is properly set in radio (or also in software for FT8, where there I have tx, click sound, tuning, tx etx properly working) but without any output power).
I have tried so far 1.1.6, 1.1.7 (the firmware that the radio came with from a SK, and the latest of September 2024). Any ideas/solutions software related? I am afraid that probably something is broken inside the transceiver. Many thanks in advance for any help.
|
Try short push of power button?
Is it possible to disable the display.
I hear many people complain about low battery life.
However a display is only really mandatory for initial tuning after that its less useful
Especially for digi modes where you tend to lock to a single frequency
|
Is it possible to disable the display.
I hear many people complain about low battery life.
However a display is only really mandatory for initial tuning after that its less useful
Especially for digi modes where you tend to lock to a single frequency
|
Re: Factory reset... not working
If you changed the root password on the system - you have 2 variants. First - flash an old xiegu firmware. Old versions rewrite all files on the system and should reset the root password. Second - boot from SD card (using R1CBU firmware, for example), mount internal storage and remove the root password hash in the /etc/shadows ()
§á§ä, 4 §à§Ü§ä. 2024 §Ô., 18:39 John Brent - VA3HQB via <john.brent= [email protected]>:
Problem I have, is that even after doing a factory reset, using userid: root, and password:123 will not allow me to login. Says denied.
|
Re: Standard FW CW decode?
toggle quoted message
Show quoted text
From: Richard (K3RWN) via groups.io
Sent: Saturday, October 5, 2024 5:26 PM
Subject: Re: [xiegu-x6100] Standard FW CW decode?
?
Thanks,
?
Thankfully we have .25!
Rich
|
Re: Standard FW CW decode?
Thanks,?
?
Thankfully we have .25!
Rich
|
Re: Standard FW CW decode?
The XIEGU FW CW decoder always works poorly. The decoder has no AFC and no automatic signal threshold. A decoder like that can never work well. Stupid programming... unfortunately. 73/6 Jens / HB9JOI +++ -----Urspr¨¹ngliche Nachricht----- From: Richard (K3RWN) via groups.io Sent: Saturday, October 5, 2024 4:53 PM To: [email protected]Subject: [xiegu-x6100] Standard FW CW decode? Has anyone had any luck in getting the CW decoder (send or receive) to work in the Xiegu FW? Is there a trick or setting that I am missing? It works great in .25 third party FW. Just curious. Rich
|
Has anyone had any luck in getting the CW decoder (send or receive) to work in the Xiegu FW?
Is there a trick or setting that I am missing?
It works great in .25 third party FW.
Just curious.
Rich
|
John Claridge 2E0JJC
SA5QED/David
John Brent - VA3HQB
Paul - AI7JR
Jens/HB9JOI