开云体育

I would first make sure that you have HAM RADIO selected under the band stacking menu before you delete anything.? My menu has only one frequency per band.

Thanks for everyones comments.. its a learning curve !??
73 Mike

Interesting... I have G90 and x6100 and noticed that G90's tuner was lot better in "tuning" my end fed.

Also shame that x6100 haven't got same tuner&SWR meter like G90 since it is better to see SWR value in numbers not sliders.

I compared x6100, to external ATU100, ATU100 was lot better "matching" my antenna to values <1.5... My antenna is shortened version on end fed 80-10... and ATU100 was able to "tune" it even on 160m to 1.6-1.7, but still G90 was able to tune 160m lower than ATU100 did.

SP9DDB
-73's-

Hi, Ray. You can toggle between the General and Ham bandstack in the menus.
--
73 de K9NUD

Sí, seguro. Y eso está bien. Una SWR de 2:1 no afectará a la protección del paso final y, además, toda la potencia irá a la antena.
Algo bueno del X6100 es que puede utilizarse en portable con antena no resonante + 9:1 UNUN. Yo lo uso así y bastante bien. La opción SWR Scan es muy conveniente.
Feliz Navidad. Desde Espa?a.

Saludos. Diego. EA1CN

--
TNX, Dido. EA1CN

hi folks
by swapping thru the bands pressing BAND buttom I have frequencies
(1) I do not use
(2) outside ham-radio-bands

(1) at this time: no worry
(2) e.g. 80m band has 2 or more presets - I Do not use more than one preset per band.
How reduce / delete those entries?

thanks for your kind assistance - Ray

I have noticed that usually when SWR is less than 1:2.0 ATU doesn't make any change.

Hi Everyone...
I just noticed using the 6100 that the little SWR meter showed that I was close to 2:1 on tx
Long story short... it appears that the internal tuner is not making any difference.
For Example, if I have a 1:6 match and it may drop it to 1:5... or no change at all.
Also, the SWR scan shows a 1:1 match and the external swr meter shows 1:5 -1.
I know the antenna is a flat match.
The TX power output is good, no issues.
The ATU is not doing its job in my opinion.
Firmware or hardware issue?
Otherwise the rig works great !
Any thoughts on this????
73 Mike VE3MKX

As original poster on this specific thread, I thought I would follow up with my successful experience.
First, I discovered it seems very important to exactly go through the suggested 4 charge-discharge cycles.? After upgrading the firmware, I casually started using the radio while only sometimes remembering to do a charge-discharge.? The result I experienced was that the battery indicator never successfully indicated correctly and it seemed that things eventually became so confused that the battery never charged, and was always at zero.? I eventually re-updated the firmware a second time, and exactly followed the suggested 4 charge-discharge cycles (even posting a yellow sticky note to the radio to keep track, because this took a few days).? a) Update firmware.? b) Turn off.? c) Leave it plugged in charging until full.? d) Unplug.? e) Turn on and leave it on until it turns off (overnight?) after running out of battery.? f) Four times.?
I now report the successful result; all is good.? The pesky little power-on-init message does not display.? The radio holds the battery for a long time when disconnected.? The battery indicator seems correct.?
All seems well.?Over 120 listen receptions on 10m JS8 and 40m FT8 over a day or so.? Next up, after the year-end, 10m JS8 xmit is planned.? It works.

I understand how NR and NB work.? I was just asking if there were any problems anyone else was having.? I agree that it does not work at all on the x6100 yet.

just use the latest.?

?

There unfortunately here are two v1.16 versions. Different release-dates.?

note that having a NB also may cause distortion with strong signals.

(I sent a mail to the creators -- asking what's the purpose and why not yet in the kernel etc)

same; what would the driver give you/us what it doesn't now?

My X6100 works fine with ACM1 in CQRLog, Jtdx, Wsjt-x, QSstv.

Pretty strange. I have several devices in Linux and the standard cdc_acm driver works fine for all