开云体育

Add me to the list who have had this knob develop the slippage issues... I put a dab of hot glue and reseated the knob and it worked fine for a few more months, before it came unglued again. I now

I had issue with the X6100 select knob.? It was slipping.? The knob was just around fitting of the shaft and I had thought it was bad.? I just added some glue to the knob and inserted on to the

Hi Ron Have you fitted a yaesu pa board into a x6100 ? Dave 2E0DMB [email protected]> wrote:

Since no power output on other modes sounds like blown PA.? The fT817/8 are not so forgiving in the PA.? I am on my 3rd PA in my 2004 FT817. If you wish to order a PA board, about $60, from Yaesu

Well Georgy, many thanks for the hint, that is the reason I believe, same with video (no worries about the language, I could feel him) Many thanks for your help, I will take the transceiver to a

Bytes sequences might be different (for example 1.1.6? - 0x4ff49672, 1.1.7 - 0x4ff49673). As far as I remember - 1.1.6 and 1.1.7 uses different MCU registers to load value. Not sure - may be it

Thanks Georgy. Actually my intent was to create a 'generic' script that in theory could be applied to any new Xiegu X6100 baseband firmware without any constraints on the checksum or the actual

Many thanks for your reply Georgy. Excellent work that we are all very thankful for. John. 2E0JJC [email protected]> wrote:

The only difference between 0.25.1 and 0.25.0 is that voice prompts is fixed in 0.25.1. I forgot to bump version, while creating 0.25.1 build. Georgy // R2RFE

I have downloaded and installed v0.25.1 from GitHub. As the x6100 boots it briefly displays the firmware as being v0.25.0 not v0.25.1? I am a little confused. Have I installed the latest firmware?

X6100 have a weak output transformer - I heard about a case, when using FT8 with high output power burnt it out (with a condenser) - https://www.youtube.com/watch?v=UVM4X2zYcpE (it's on Russian, but

I created an issue - https://github.com/gdyuldin/x6100_gui/issues/9 73

Thanks Franko. I created a bit more strict script for patching, while I apply changes to 1.1.8. It checks md5 of source before patching, uses predefined offsets for changes and checks, that content on

Thanks Georgy. Based on your patches to Xiegu BASE firmware, tonight I wrote a simple Python script (attached) that should apply the corresponding changes to future (or older) Xiegu BB firmwares

When GPS is connected and has acquired a position fix, it would be nice to have the QTH automatically populated with the current Maidenhead locator. 73 de SA5QED/David

Sorry to hear. Could an R1CBU 0.25.0 user report on your experience with this issue? Did you experience FT8 TX issues that R1CBU 0.25 resolved? Thanks for your input, and thanks to the developers of

Dear Tony and John, unfortunately none of the upgrades worked for me. I do not if I will be able to find the receipt from the relatives of the SK to check if the warranty is still valid and then I

I didnt set a root password, but I am also not the first owner of this radio. They may have changed it. I am flashing it with 1.1.4 now. We will see what happens when I update that.

Turning off the display has almost no effect on power consumption. Much more significant if BT/WiFi is disabled

" root, and password:123 will not allow me to login. Says denied." I would bet that Factory Reset doesn't change/restore the user passwords... Did you previously (intentionally) change the root