Re: R1CBU firmware 0.22.0
¿ªÔÆÌåÓý?
... where I can see the wifi connection for automatic log upload e.g. to
e-qsl ?
... where I can set the/adjust the parametrs/enties e.g url for automatic
log uploads ?
?
73 , Jens
?
+++
?
? From: g.dyuldin@...
Sent: Friday, August 16, 2024 5:35 PM
Subject: [xiegu-x6100] R1CBU firmware 0.22.0 ?
[Edited Message Follows] New:
*
CW tuner - shows how accurately the radio is tuned to the correspondent's
frequency. I had to
slightly change the signal preprocessing for the CW decoder - now it works a
little differently.
*
Adjusting the bandwidth for filters with one knob. I did it for CW, but did not disable it
for other modes. For CW - the center of the filter always equals to the key
tone.
* Low and
High filters in CW mode change synchronously (central frequency remain
unchanged).
* Simple
level indicator in the recorder.Perhaps, will restyle/rework it in the
future.
* Time sync
in FT8 application. When
pressed, rounds the current time on the transceiver to the nearest FT8/FT4
slot. Usage - listen
to the broadcast, find a section of silence, press the button - the system time
will be updated. I guess it's simpler, than trying to adjust using
settings.
*
ADIF log for FT8. Call signs,
reports, QTH are saved. Checked import to hamlog.online, eqsl.cc,
qrz.com.
* Noise reduction and Noise blanket can be
assigned to f1/f2 headset
buttons
* Battery icon.
The charge level is calculated by
voltage
*
Charging
icon
* Support reading
transceiver ID via CAT. Should help solve the problem with some versions of
Hamlib
* Display peaks on
S-meter
?
Changed:
* FT8 app
now uses USB-D. The sound
from the microphone is not mixed into the transmission, and the transmission
does not break down after using the ATU.
* The output
power in the FT8 application match to the installed one. Looks like for internal signal sources the
changing output power only works as a limiter (ALC threshold adjustment).
* Auto level
for waterfall/spectrum is disabled during transmission. Fixed values ??are used during
transmission. After the
transmission is completed, the auto level is used again.
* The
buttons on the left (GEN, APP, etc.) ¡°scroll through¡± the corresponding button
blocks of buttons below.
* Recording
and playback levels in settings app are now in decibel s (default 0, range from
-10 to +10).
* Switching
to digital modes and back - by long pressing the SSB button. Short
press for the LSB/USB or LSB-D/USB-D
switch.
* In digital
mode, the LSB-D/USB-D inscription changes color.
* Power
meter, SWR and ALC smoothing is disabled in digital modes.
Fixed: * Band "jump" if the transceiver is in the lower range and is tuned to the upper limit. * Zooming spectrum doesn't affect levels. * When
changing band/A/B, the waterfall does not forget the data.
* Deleting a
single entry/message now clears the table.
* Fixed some bugs with
the FT8 application
* Freezes when using
headset buttons (possibly my mistake, but now fixed)
* Minor stability and
performance improvements
?
Also, I
raised the recording level in the audio mixer that comes with SDR on linux and
is used for recording, CW and FT8 decoding, etc. Initially the sound is very quiet - maybe this is
a problem with my transceiver.
?
Update via
patch - connect the card to the computer, and drop the tgz file into the DATA
disk (for those with Linux - into the root of the DATA partition).
The
transceiver will update the files on first boot.
?
|
Jens/HB9JOI