So sad, "out of Stock"
--
Walt, WD0GOF, WD0GOF.COM

开云体育

You can also see that both DFU devices reported have the same serial number, indicating it comes from the same physical device.

No I did not have any other DFU devices, because if i disconnect the tinySA Ultra it does not see any DFU device when starting the bat file.
When the tinySA Ultra is reconnected the bat file again reports multiple devices.
Only when calling the bat file before switching on the tinySA Ultra in DFU mode it went well.
Could it be that the factory firmware has multiple DFU devices?

On Sun, Dec 4, 2022 at 03:39 AM, Peter Bremer wrote:

More than one DFU capable USB device found!

It seems you had more than on DFU capable device active

Make sure the tinySA is the only device connected in DFU mode
?
--

It looks like I first needed to start the batch file and while it said "Device will detach and attach" switch on the TinaySA Ultra in DFU mode.
Then it suddenly upgraded to 512. According 'version menu':?

If I execute the bat file DFU_LOAD_BIN.bat as indicated in the wiki, I get the following error:

C:\Program Files Special\tinySA_Ultra>.\dfu-util-static.exe? -a 0 -s 0x08000000:leave -D .\tinySA.bin

dfu-util 0.11

?

Copyright 2005-2009 Weston Schmidt, Harald Welte and OpenMoko Inc.

Copyright 2010-2021 Tormod Volden and Stefan Schmidt

This program is Free Software and has ABSOLUTELY NO WARRANTY

Please report bugs to http://sourceforge.net/p/dfu-util/tickets/

?

Warning: Invalid DFU suffix signature

A valid DFU suffix will be required in a future dfu-util release

More than one DFU capable USB device found! Try `--list' and specify the serial number or disconnect all but one device

?

?

C:\Program Files Special\tinySA_Ultra>.\dfu-util-static.exe -l

dfu-util 0.11

?

Copyright 2005-2009 Weston Schmidt, Harald Welte and OpenMoko Inc.

Copyright 2010-2021 Tormod Volden and Stefan Schmidt

This program is Free Software and has ABSOLUTELY NO WARRANTY

Please report bugs to http://sourceforge.net/p/dfu-util/tickets/

?

Found DFU: [0483:df11] ver=2200, devnum=30, cfg=1, intf=0, path="1-1", alt=1, name="@Option Bytes? /0x1FFFF800/01*016 e", serial="2058365F2039"

Found DFU: [0483:df11] ver=2200, devnum=30, cfg=1, intf=0, path="1-1", alt=0, name="@Internal Flash? /0x08000000/128*0002Kg", serial="2058365F2039"

Found Runtime: [30c9:003a] ver=0006, devnum=3, cfg=1, intf=2, path="1-4", alt=0, name="Camera DFU Device", serial="0001"

?

C:\Program Files Special\tinySA_Ultra>pause

Press any key to continue . . .

(From R&L) I was prepared to re-align the lcd, but found mine is perfect so I can get right to the fun!

开云体育

开云体育

开云体育

Is it possible to just rotate the display in its case?

On Sat, Dec 3, 2022 at 04:15 PM, Barry wrote:

Just got new Tiny Ultra.? Upgraded the firmware per the document using STM32 Cube Programmer.? Upgrade went well and Programmer showed that the upload was completed.? After turning the unit Off and On, the screen is black.? I can connect the Programmer to the SA and read the files.? Did I miss something?? Hoping for some help.

Did you use the correct file format (bin) and the specific file for the tinySA Ultra (not the tinySA)?

Did you follow the steps in Erik's guide?
?

Roger

开云体育

Hi, Eric,
I've also noticed that when I change the brightness of the display, this setting only applies until TinySA is turned off. It would be good if the brightness setting was part of STORE AS STARTUP.

Today I was using TinySA (with RF probe) to repair a home made UHF transceiver and it was very pleasant to work with. Beautiful instrument!

Mirek

R & L Electronics
Clyde KC7BJE?

开云体育

--
Walt, WD0GOF, WD0GOF.COM

I received mine from R&L yesterday and immediately noticed the screen was mis-aligned with a tilt that cut off the upper left text.? What a relief it was to have this groups.io where I could learn that a) I was not the only one to have the issue and b) it is easily corrected.? And even better, after using the TinySA Ultra for a few minutes the display "fixed" itself, shifting into a straightened view.? I am assuming it must have just shifted a bit during shipping.

I already had the original TinySA, but this upgrade to the Ultra is worth every cent, and Erik deserves the equivalent of an academy award for bringing these powerful tools to the "radio table" for such a low cost.? I came very close to spending 20X the cost for an additional spectrum analyzer with a higher frequency range, had I not learned of the new Ultra version.

开云体育

Okay, Eric, I understand.
I'm gonna describe another little problem. Example:
I set the frequency to 50 to 100 MHz.
I click on the marker, the marker becomes active.
Then I execute: MARKER... MARKER OPS...CENTER
The action executes correctly, but after the action, a triangle appears in front of SPAN on the bottom right of the display, indicating that SPAN is active. However, Jog does not change the value of SPAN where the triangle is, but changes the value of CENTER.
But I think after the OPS CENTER action the marker should remain active, Jog should still move the marker.

Mirek

On Fri, Dec 2, 2022 at 11:55 PM, MirekD wrote:

(TinySA reports it as 511)

Should be ok now.

The generator and the SA use the same backup locations for frequency and span so when switching between the modes the frequency will always be reset.
?
--