¿ªÔÆÌåÓý

  1. Tinysa
  2. Messages
Expanded Topics Messages Polls
Date
Re: Question: Settings vs Config vs Profile

 

On Thu, May 1, 2025 at 06:32 AM, Vladimir Kiesner wrote:
LO OUTPUT?enables the output of the first LO through the high connector
Should be? CAL connector
--
Designer of the tinySA
For more info go to

Re: Question: Settings vs Config vs Profile

 

LOW and HIGH connectors are TinySA BASIC only and should not be confused with the RF and CAL connectors of the TinySA Ultra.?

The Ultra has a switch IC to steer the various internal inputs and outputs to the RF connector.?

On Thu, May 1, 2025 at 8:51?AM Vladimir Kiesner via <vladimir.kiesner=[email protected]> wrote:
But where is high connector in Ultra model? Is it just leftover from TinySA firmware?
Re: Question: Settings vs Config vs Profile

 

But where is high connector in Ultra model? Is it just leftover from TinySA firmware?
Re: Question: Settings vs Config vs Profile

 

LO =local oscillator?
Re: Question: Settings vs Config vs Profile

 

For TinySA Ultra+?
CONFIG:
  • LO OUTPUT?enables the output of the first LO through the high connector
?
Can you explain what is this, because I think about LO as TinySA lower output port and this does not compute :)
?
Re: Question: Settings vs Config vs Profile

 

So, I see LEVEL CAL is under CONFIG.
Does this mean CONFIG->MORE->CLEAR CONFIG, Unit must be recalibrated?
?
Re: Verification by serial number?

 

I can say that if you buy from R&L Electronics, you can absolutely be guaranteed of getting a legitimate unit. I have purchased a TinySA, a TinySA Ultra and a NanoVNA H4 from them. All are excellent. I have purchased many other things from this company, too, and I am very happy with them.

Zack W9SZ

Virus-free.


On Thu, May 1, 2025 at 8:03?AM Dave King via <kingdws=[email protected]> wrote:

Thanks Erik. I didn't expect you to answer but it is nice to see the designer active !
I did buy from Zeenko so that much is ok. The unit is the base Ultra model. It accepted the update code from the wiki and it happily made squiggly things after ;-)? I did see the production date as Feb 24. It connected to my windows workstation no problem but I wasn't familiar enough with it to make bigger squiggly things...

I haven't tried a update and complete self test yet.? Hopefully can do that today.

I am curious about the rampant clones, did that happen after getting a company to do boards or units? I have heard quite a few stories of designs walking out the back door and getting built in the shed and sold as originals (not mentioning country but you know where).

Looking forwards to working with this.

Dave


On Wed, Apr 30, 2025, 9:49 p.m. Erik Kaashoek via <erik=[email protected]> wrote:
The only way to know for sure is to buy from an approved seller, see wiki
--
Designer of the tinySA
For more info go to

Re: Verification by serial number?

 

Hi Clyde

It was from one of the listed companies "Zeenko".

Dave


On Wed, Apr 30, 2025, 9:56 p.m. Clyde Lambert via <clyde.lambert=[email protected]> wrote:
Where did you purchase it?

On Wed, Apr 30, 2025, 9:49?PM Dave King via <kingdws=[email protected]> wrote:
Hi
?
I just purchased my TinySA Ultra after running across it but after reading a bit I am now paranoid as to its authenticity. I saw and understand the designer posting that he didn't want to give away how to tell the difference. Mine came in a nice TinySA black box and the unit itself looked like nice quality along with all the components that were included. Being new to this I wonder if the authenticity can be done by the serial number thru a PM so not to deseminate the information?.
?
I did look to see if this had been asked and answered....
?
Thanks!
?
Dave
Re: Verification by serial number?

 

Thanks Erik. I didn't expect you to answer but it is nice to see the designer active !
I did buy from Zeenko so that much is ok. The unit is the base Ultra model. It accepted the update code from the wiki and it happily made squiggly things after ;-)? I did see the production date as Feb 24. It connected to my windows workstation no problem but I wasn't familiar enough with it to make bigger squiggly things...

I haven't tried a update and complete self test yet.? Hopefully can do that today.

I am curious about the rampant clones, did that happen after getting a company to do boards or units? I have heard quite a few stories of designs walking out the back door and getting built in the shed and sold as originals (not mentioning country but you know where).

Looking forwards to working with this.

Dave


On Wed, Apr 30, 2025, 9:49 p.m. Erik Kaashoek via <erik=[email protected]> wrote:
The only way to know for sure is to buy from an approved seller, see wiki
--
Designer of the tinySA
For more info go to

Re: Question: Settings vs Config vs Profile

 

Everything you set in the CONFIG menu is in the Config.
Everything else is in Settings which can be stored and recalled from preset
--
Designer of the tinySA
For more info go to

Question: Settings vs Config vs Profile

 

Hello. Please clarify, what parameters are stored in:
- Settings
- Config
- Profile
Or, what is difference between them.?
Unit: TinySA Ultra+
Re: Verification by serial number?

 

Where did you purchase it?


On Wed, Apr 30, 2025, 9:49?PM Dave King via <kingdws=[email protected]> wrote:
Hi
?
I just purchased my TinySA Ultra after running across it but after reading a bit I am now paranoid as to its authenticity. I saw and understand the designer posting that he didn't want to give away how to tell the difference. Mine came in a nice TinySA black box and the unit itself looked like nice quality along with all the components that were included. Being new to this I wonder if the authenticity can be done by the serial number thru a PM so not to deseminate the information?.
?
I did look to see if this had been asked and answered....
?
Thanks!
?
Dave
Re: Verification by serial number?

 

The only way to know for sure is to buy from an approved seller, see wiki
--
Designer of the tinySA
For more info go to

Verification by serial number?

 

Hi
?
I just purchased my TinySA Ultra after running across it but after reading a bit I am now paranoid as to its authenticity. I saw and understand the designer posting that he didn't want to give away how to tell the difference. Mine came in a nice TinySA black box and the unit itself looked like nice quality along with all the components that were included. Being new to this I wonder if the authenticity can be done by the serial number thru a PM so not to deseminate the information?.
?
I did look to see if this had been asked and answered....
?
Thanks!
?
Dave
Re: Bug report: Multiband name does not stored in bnd file.

 

I second this. Presets do store names, which is a workaround meanwhile.
Re: Bug report: Multiband name does not stored in bnd file.

 

P.S. Another issue with same feature: when disabling band element, name in menu replaced with frequencies, and name on screen became start frequency.
Bug report: Multiband name does not stored in bnd file.

 

¿ªÔÆÌåÓý

Hello. I've opened issue#136 on
Not sure if github is in use.
Here is a copy:?
I created multiband config for all 8 slots and named each slot. after saving BANDS->SD, i have found, what xxx.bnd file does not have any names inside. Of course, loading bnd file back confirm this issue. All slots named as tx1,rx1,tx2,rx2, etc.
Please fix this issue and store band name in "bnd" file. Thanks!
P.S. Model TinySA Ultra+ ZS-406, firmware tinySA4_v1.4-199-gde12ba2
?
Vladimir Kiesner
Re: Typed 0000 in the 'internals' menu and now the tinySA ultra freezes immediately after boot

 

Are you running the latest FW?
The only thing left is to load a very old FW (maybe the oldest Ultra FW you can find) and then load the latest FW. THis will force a reset of any preset and config data saved.
--
Designer of the tinySA
For more info go to

Re: Typed 0000 in the 'internals' menu and now the tinySA ultra freezes immediately after boot

 

Level indicators did not turn red. I have tried this maneuver many times over the last couple of days and the behavior is as stated above in every case
Re: #tinysa #ultra Leveling TinySA Ultra with damaged LNA #tinysa #ultra

 

Yes
--
Designer of the tinySA
For more info go to

201 - 220 of 19818