开云体育

The photos on this page
aren't enough? You'd
have to extrapolate dimensions from IC inter-pin spacing, but they all
appear to be the same and there appear to be no other dimension-critical
parts of the board.

- Roland 9V1RT

------------------------------------------------------------------------

On 5/12/24 05:22, Christopher Prioli AD2CS via groups.io wrote:

Does anyone have any of the following that they would be willing to

share? These are all in reference to a SoftRock Lite v6.2 (NOT the Lite II
-- the square board with two mounting holes is what I need) -- in reality,
my kit is marked as a v6 kit, but I cannot seem to find anything directly
related to that rev level.

I could use:
-- a set of Gerber files for the board, or
-- a Kicad or Express PCB drawing of the board, or
-- a good clear photo of the bare board with dimensions, or
-- a bare board that I could clone and return.

I will pay any postage fees involved, of course...

On Dec 4, 2024, at 11:47?PM, Chuck Nolin via groups.io <wa6ltv@...> wrote:
?Hello Christopher,
Did you check this page??

WB5RVZ Softrock Software Defined Radio Homepage (www.wb5rvz.com) ( )
wb5rvz.com ( )
( )

( )

This is the home page ok the link you got?

Chuck

On Dec 4, 2024, at 6:14?PM, Christopher Prioli AD2CS via groups.io
<cpprioli@...> wrote:

? Thanks -- I have another set of board photos, and that is exactly what I

figured that I would have to do, but I was just hoping that there was an
easier way.. LOL

73 de

-- Chris AD2CS
*GCARC Education Committee Chair*
*GCARC Membership Committee Chair*
*Member, GCARC Board of Directors*
------------------------------------------------------------
Christopher P Prioli
648 W Holly Ave
Pitman, NJ 08071
1-856-689-6783
www.ad2cs.com


On Wed, Dec 4, 2024 at 6:06?PM Roland Turner via groups.io <roland=
[email protected]> wrote:

The photos on this page

<> aren't enough? You'd

have to extrapolate dimensions from IC inter-pin spacing, but they all

appear to be the same and there appear to be no other dimension-critical

parts of the board.

- Roland 9V1RT

------------------------------------------------------------------------

On 5/12/24 05:22, Christopher Prioli AD2CS via groups.io wrote:

Does anyone have any of the following that they would be willing to

share? These are all in reference to a SoftRock Lite v6.2 (NOT the Lite
II

-- the square board with two mounting holes is what I need) -- in reality,

my kit is marked as a v6 kit, but I cannot seem to find anything directly

related to that rev level.

I could use:

-- a set of Gerber files for the board, or

-- a Kicad or Express PCB drawing of the board, or

-- a good clear photo of the bare board with dimensions, or

-- a bare board that I could clone and return.

I will pay any postage fees involved, of course...

On Dec 4, 2024, at 6:14?PM, Christopher Prioli AD2CS via groups.io
<cpprioli@...> wrote:

? Thanks -- I have another set of board photos, and that is exactly what I

figured that I would have to do, but I was just hoping that there was an
easier way.. ?LOL

73 de

-- Chris ??AD2CS
*GCARC Education Committee Chair*
*GCARC Membership Committee Chair*
*Member, GCARC Board of Directors*
------------------------------------------------------------
Christopher P Prioli
648 W Holly Ave
Pitman, NJ ?08071
1-856-689-6783
www.ad2cs.com


On Wed, Dec 4, 2024 at 6:06?PM Roland Turner via groups.io <roland=
[email protected]> wrote:

The photos on this page

<> aren't enough? You'd

have to extrapolate dimensions from IC inter-pin spacing, but they all

appear to be the same and there appear to be no other dimension-critical

parts of the board.

- Roland 9V1RT

------------------------------------------------------------------------

On 5/12/24 05:22, Christopher Prioli AD2CS via groups.io wrote:

Does anyone have any of the following that they would be willing to

share? ?These are all in reference to a SoftRock Lite v6.2 (NOT the Lite
II

-- the square board with two mounting holes is what I need) -- in reality,

my kit is marked as a v6 kit, but I cannot seem to find anything directly

related to that rev level.

I could use:

-- a set of Gerber files for the board, or

-- a Kicad or Express PCB drawing of the board, or

-- a good clear photo of the bare board with dimensions, or

-- a bare board that I could clone and return.

I will pay any postage fees involved, of course...

Does anyone have any of the following that they would be willing to share? These are all in reference to a SoftRock Lite v6.2 (NOT the Lite II -- the square board with two mounting holes is what I need) -- in reality, my kit is marked as a v6 kit, but I cannot seem to find anything directly related to that rev level.

I could use:
-- a set of Gerber files for the board, or
-- a Kicad or Express PCB drawing of the board, or
-- a good clear photo of the bare board with dimensions, or
-- a bare board that I could clone and return.

I will pay any postage fees involved, of course...