开云体育

Christopher, I used the picture off the back of the board from stage 3 of the assembly instructions( divider) Scaling from the chip pad spacing with 8 pads I get board width 2.99 inch in the

Hello Christopher, Sorry, check the link at the end. That goes to the original home page that has the complete build notes. I kind of botched that post. Sorry Chuck

Hello Christopher, Did you check this page?? WB5RVZ Softrock Software Defined Radio Homepage (www.wb5rvz.com) ( http://www.wb5rvz.com/sdr/ ) wb5rvz.com ( http://www.wb5rvz.com/sdr/ ) (

Thanks -- I have another set of board photos, and that is exactly what I figured that I would have to do, but I was just hoping that there was an easier way.. LOL 73 de -- Chris AD2CS *GCARC

The photos on this page <https://www.wb5rvz.com/sdr/New_SR_Lite/02_lo.htm> aren't enough? You'd have to extrapolate dimensions from IC inter-pin spacing, but they all appear to be the same and there

Does anyone have any of the following that they would be willing to share? These are all in reference to a SoftRock Lite v6.2 (NOT the Lite II -- the square board with two mounting holes is what I

Hi all. Looking for the skins for psdr they appear to not available any where or not able to be downloaded Just want get my MOBO board back in use. Tried PowerSDR v2.4.4 which thought was what I use

You might check PCBshopper for competitive prices. Just put in your board size and qty of 3 (OSHpark sends 3 bds, and the others will default to 5) Bump the shipping time to longest time for

Christopher, I cloned the Lite board in the Diptrace PCB layout system. Diptrace is free for small boards. If you send me an email address, I can send either the Diptrace file or a Gerber file. (

TRY: https://www.softrock40.com/product-page/bare-board <cpprioli@...> wrote:

I was recently given three different SoftRock kits - the RXTX v6.2 40m, the RXTX v6.2 80m, and the SoftRock Lite v6 40m. I have successfully assembled both of the larger kits. However, the Lite kit

Thanks everyone, it has found a new home. Dennis KK5DB

Hi Dennis, I would love to get the RxTx up and running. I built one for 17m when I was first licensed - before I knew anything about which bands to operate. My local club holds QRP Saturday when the

Hi Dennis. I gave the last one a home ( its owner). I can fix this. And send it back to you if you like. I don’t have any more cases though. I will send this note to you. I will pay the shipping.

I also have an Ensemble RXTX 40,30,20 which has been completely assembled and tested good up to RX-mix or RX_OpAmps. I can't remember what the issue was but I gave up and haven't touched this for

Good morning Joe; I will give it that good home and more! I sent you an email. 73 de N1GMM Guy -- guy (at) eastroad (dot) org -.-. --.- -.-. --.- -.. . \|%|/// | ~ ~ | ^( @ @

I had started this kit pre-pandemic and got to stage 5 RFI 10 when my voltage checks failed. In spite of much help from this group and others, I could not correct the problem and the partially built

Steve, Are you following Robby's pages https://www.wb5rvz.org/ensemble_rxtx/03_lo ? If so I am assuming that is as far as you have got. At that stage the Si570 signal will not be very strong unless

Are you running the pa test ? Did you watch the HamNation 82 test that was done, its in the latter half of the episode. ? They had a similar problem it was incorrectly installed T3 , the orientation

I purchased this kit in 2012 and and had a stroke .I.ve finally recovered enough motor skills to build the kit. Now on to my question I'm in the local osc. stage and ever thing seems to be 'almost ok"