开云体育

I have available free for pickup three vhf Micor base stations. One of them has a 136-150mHz PA deck, that was working when last in service about ten years ago. There have been various parts robbed, but believe there is enough here that one complete repeater could be assembled. I believe there is a native 142-150mHz receiver as well. The collection comes with a set of NOS 8560 finals. Free for pickup in West Terre Haute, IN. You must take the entire lot. Contact me direct at k9hxATyahoo if interested. I do gave a few pictures, but the cabinets are against a wall, and are a little dirticult to move to get better shots. There are three loose HP power supplies, status unknown. Thanks and 73, Kevin, K9HX

Hello All. I am having issues programming a VHF DeskTrac Repeater and wanted some insights I've built close to 8 Different Cables all listed as "DeskTrac"or"MaxTrac" and I have not been able to get it to program I am using a RIB Box and switching the Blue 1, 2, and 3 switch on the DeskTrac the PC is running Windows XP With DosBox with the serial port Forwarded to Serial 1 (an actual Serial Port on the Laptop) sometimes the Data light will blink then start rapidly blinking but after like 1/2 a Second it just sits there with nothing and blinks every 1/2 - 1/4 of a second then the software goes Cannot read Data

Looking for Yaesu scu 20 for fusion if anyone has one for sale thanks n4jem

All, Have a nice UHF MTR-2000 40w we are looking to use for 44 ham usage. Starting from a clean default profile, it programs up perfectly and will operate perfectly. But if powered down, TX audio & CW ID are way down, etc. It's like it's losing settings. Reload the codeplug and it's back in business. Test menu every thing works perfectly, including deviation. I'm wondering if it's go an issue like the quantars with worn out non-volatile memory (EEPROM, E2PROM, or similar). Anyone dealt with this before? Any suggestions appreciated. This repeater is otherwise very nice and hears extremely well. Thanks in advance, Alan Barrow KM4BA

Looking for a Secure Capable Station Control Board for a UHF 100w MSF 5000, had an SCR smoke. Was also dealing with some occasional noise on the TX. TLN 3043B0818K. Any options would be welcome, and if you have the entire MSF5000 of similar model we might be interested in some other parts. Thanks, Alan Barrow KM4BA

I had a TKR 750 working on a RLC 3 Controller. I bought a New TKR D710 and hooked it up to the same cable and configured the D710 just about Identical to the TKR 750. If I let the Repeaters internal controller control the Repeater I get normal Audio out of the repeater but when I turn off the Repeat enable and let the RLC control it I get PTT on the D710 but no Audio just Carrier I also have TKR 850 on another Port it will key up but no Audio and if I talk into the TKR 850 it repeats fine out of it but the D710 Transmits but no Audio out. I have Aux In/Out 4 Set to Encode Signaling Enable, Aux Out 5 COR Active Low and Aux In/Out 6 TOR Active Low. Ted McArthur kb7pab@... 435-770-9169 Callsigns AC7II _ Amateur D-451_Cache County Ecomm 59-A-40_State of Utah DEM WRJH-604_General Mobile Radio Service

I am building a Duplexer for a GMRS repeater. I have a Wacom WP-678 that is missing the interconnect cables. I did a little search hoping I could find some documentation on the lengths for cutting new ones. 462/467 split. Anyone know these off the top of their head, or have a chart somewhere? TNX Jim Sent from Outlook Virus-free.www.norton.com

Looking to swap a brand new ics control quantar 1x for the northcomm quantar ecm and program cable. I'm looking for a more simple plug and play solution than something I need to jump through all sorts of gyration to get up and running. And I don't need all the capabilities of the ics I just need remote disable, and courtesy beep. So the northcomm might be better for me and the ics might be suited to someone who has more patience than i do to set it up properly and needs the advanced functionality of the ics. I'm only using this on a gmrs repeater so I don't need a bunch of advanced features or digital linking. My understanding is the northcomm is just set wildcards in quantar and then 1 adjustment on the board that requires no test gear to set it up. Suffice to say I can't get courtesy beep or remote disable to function on my quantar with the ics and the ics is brand new. I got voice id'er to work fine so I'm sure it's a setting on the ics board. I'm just out of patience to screw with it. I want an overall plug and play unit. I will also sell the ics outright for what i paid for it in leu of a swap. Let me be clear it's not ics fault it's l something I'm not doing correctly and I don't have the eyesight or dexterity in my hands anymore to work with small stuff like this board. Thanks Robert Chrysafis Kc8gpd Wrcm325 Scottsbluff NE

Hi to All, I just bought a nice Motorola CDM-1250 Low-Band modified for 6 Meter Ham Band. But I am looking for the Service manual and I can only find the manual for VHF and UHF. The radio does work and turn on by the ignition accessories plug pin but I have some problem with the control head. No ON-Off button function, no Lights for the display, no RX-TX light, no Lightening of the DTMF Mike. And I have some question on the output power specs of this radio, it is set to 65 Watts in CPS put putting out 90 W on my Bird Bench Wattmeter? My Model is : AAM25DKD9AA2AN I am hoping that a member as seen this control heads problem before and somebody as the proper manual for this radio. Or at least the model number info to know what is the normal output power of this radio? Thanks’ to all for looking in their electronic document file. Best 73 Carl VA2CMB

hello everyone, well i am thinking of doing an Hard reset,,,or Factory rest for my VHF Low Split repeater.It was used on a commercial site so it must have some "special setup" so i am looking for the 2 files,The RX and the TX file of a working repeater,i would need only to change for my frequency! maybe someone could share it with me! i will appreciate the help, Tait are not known very much here ,we are in Motorola and Kenwook land!!! thanks a lot. 73/s Gervais,ve2ckn

Hi, I own a MTR2000 UHF Low Band High Power. Apparently there is a way to get this low band within the ham band (430-440). I once saw a description on the repeater-builder website but can't find anything about it anymore. Is there anyone who can help me on my way? Thanks in advance, Manu - ON7FQ

Hello everyone, i am trying to programm my TB7100 Vhf to worked with Scott RB-USB RIM "Lite". Anyone has done it and if so maybe he could share the file of this repeater or just a picture where i should go to set it up! i am almost ok,my AllStar 2.0 is transmetting but it does not hear me but first i need to be sure the Tait is ok! thanks in adavance for your help, it will replace a simplex node here. 73/s Gervais,ve2ckn

Motorola VHF Quantar SN 509CLR1418 stolen from site last Thursday... Along with DB4060B ...missing mounting brackets. Both tuned to 146.36/96 pair they cut the tie wraps holding the 4 cans together..the brackets had been misplaced but found and were to be reinstalled when repeater was discovered missing Also cables from rptr to duplexer and duplexer to Heliax gone....Sinclair Duplexer in cabinet that the rptr was sitting on not touched nor a UHF MII repeater...so this was personal....and I have 4 suspects in the list. Sheriff's office has been contacted. Contacting Boone Co Iowa (ironic) where the duplexer was bought from to get the SN on both units bought..lost the paperwork Chris WB5ITT

After further organizing my storage facility, I have found the following items: ICOM UX-59A 6M band unit for IC-900/901 - New and unused. ICOM UX-39A 220 band unit for IC-900/901 - New and unused. ICOM UX-129A 1200MHz band unit for IC-900/901 - New and unused Asking $200 each plus shipping from 95762 RLC-ICM ICOM IC-900/901 Band Module Controller. Includes 4 interface boards, ribbon cables and metal case - New and unused Asking $200 plus shipping from 95762 CommSpec TS-32P CTCSS Encoder/Decoder - New and unused - ( I have 5 ) CommSpec TS-64 CTCSS Encoder/Decoder - New and unused - ( I have 2 ) CommSpec DCS23 DTS Encoder/Decoder - New and unused ( I have 3, one without the manual ) Asking $50 each - Free Shipping I accept Venmo or Zelle. If interested, please PM me. Thanks and 73, Craig (AA6CG)

Has anyone successfully interfaced an external MMDVM board to the RS-232 accessory connector on the Kenwood NXR repeater? I know the pinouts between the TKR-850/1 and the NXR appear identical in terms of what's required to tie to a MMDVM (the RB board for e.g), however I'm wondering if the NXR may be prone to audio phase distortion should it use a DSP based discriminator similar to a Quantar or XPR etc. Anyone using one of these on DMR or P25 that can confirm it does or does not work with the external digital modem? Regards Kirb. VE6IV

Have two Kintronic isocouplers VHF FMC-0, large style. Came out of service working when tower was converted. Those folks on an AM "hot" tower know what these are. Free for shipping costs, estimate $60 each to ship inside the US. Contact me directly if interested. Chris - KC4CMR